Question about RCA P52812BL 52" Rear Projection Television

1 Answer

Rca p5270lv wont turn on just hear faint click when plugged in

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 1 Answer

Rca p5270lv TO MUCH RED ON SCREEN

Posted on Jun 04, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Will not turn on hear faint click but no lights


replace the deflection board. You can get the ITC222A deflection board from www.tvrepairworld.com

Apr 15, 2010 | RCA R52WH73 Projection Television

2 Answers

My rca p52960 tv will not turn on at all. What can


I would disconect the front control panel you can do it by opening the back of the unit on top of the light box there is a couple plugs just unplug the one going to the front panel then try to turn it on with the remote

Jan 25, 2010 | RCA P52960 52" Rear Projection Television

2 Answers

Wont turn on hear a faint click sound


The faint click sound is the protection circuit that keeps turning off the TV. This happens when an internal fault is detected. Try first leaving the TV power cord unplugged for some times, let say one hour or so. Also ensure that the fault is not coming from a faulty receiver box sending bad signal, check if you get same problem with no receiver box or dvd connected. If that does not work, and you keep having a flashing led on front of the TV, and tv turning off by itself after a while, that indicates a fault condition. The flashing light indicates a diagnostic state called protection. When the TV goes on protection there are only two possible reasons. 1The internal circuits are jammed because of electrostatic charges accumulating on capacitors, or because of a wrong voltage read by the main chip on your monitor controller board. this started the protection circuit. 2 The protection circuit detected a wrong voltage or abroken contact, identified an internal fault and kicked in , startingthe flashing light. If you are in situation one, then theTV will reset just unplugging power cord for one or two hours,sometimes even minutes. If you are in situation 2 , then there is an internal fault. Common faults that can occur are a blown capacitor on power board, a convergence IC has blown, or a fault on Digital board. Check also the video cable or any external connection cable, if the cable is shorting, or the connector is bad, you can get same flashing state because of the video cable. If under warranty contact the manufacturer ringing the number on the user manual If you want to repair at your own expenses, just locate any good qualified repairer.

Jun 05, 2009 | RCA P52812BL 52" Rear Projection...

2 Answers

RCA D52W20 HDTV TRIES TO TURN ON 3 TIMES BUT WONT POWER UP


remove all the electrical wire connections from the back of the tv .remove the power plug from the electrical outlet and wait for two minutes and replug the wire and then ckeck.it should work.
reply.

Oct 29, 2008 | RCA D52W20 52" Rear Projection HDTV-Ready...

1 Answer

Tv repair


Does the power indicator blink? If so let me know how many blinks it blinks. Respond to this post so I have a way of keeping your symptoms and model number available for furture responses.

Jun 23, 2008 | RCA D61W20 61" Rear Projection Television

2 Answers

Problem with rca big screen


possible balast problem it fires the lamp assy.you should hear a high voltage hiss when firing up from a dead stop,unplug and listen when you fire it up again.

Apr 14, 2008 | RCA D52W20 52" Rear Projection HDTV-Ready...

1 Answer

RCA Projection TV will not turn on


hey,
I just fix my RCA p46770ck with that faint click sound when you try to power on. It was the HV splitter for $74.and change. after a long hunt to find the source of the problem I did what my local appliance store said to do replace the hole board for $275 luckily I was able to return that because it did nothing different than my board/module click.... click.... clickclickclickclickclick turn on you peace of @#%! any way if you unscrew the back cover off you'll see a black box at the top left corner with 4 red wires going to it groped 3 and 1. The 1 is your HV (High Voltage) supply and then gets split to each tube. Oh you should of unplug the tv before you touch any thing HV is 30,000 volts after you unplug you should push the power button to get ride of all voltage. please feel free to contact me at Heicheltechservice@hotmail.com for any Q: I can get part numbers or help in any whey i can

Nov 06, 2007 | Projection Televisions

1 Answer

Wont turn on


Hi ,your trouble could be a 2200 35v cap on the high voltage power supply,its in the middle of the board behind a little u shaped heat sink,the cap is green and if its bad the top will be pushed up,hope this helps

Oct 14, 2007 | RCA D52W19 52" Rear Projection Television

1 Answer

My tv wont turn on


I am having the same issue. I think it's the bulb.

Aug 04, 2007 | RCA D52W20 52" Rear Projection HDTV-Ready...

Not finding what you are looking for?
Projection Televisions Logo

Related Topics:

95 people viewed this question

Ask a Question

Usually answered in minutes!

Top RCA Projection Televisions Experts

The Wyzzyrd

Level 2 Expert

83 Answers

D. E. Hev

Level 3 Expert

1059 Answers

Ron Dufek
Ron Dufek

Level 3 Expert

398 Answers

Are you a RCA Projection Television Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...