Question about Pioneer TS-W3004SPL Car Subwoofer

1 Answer

Wiring diagram for Pioneer TS-W3004SPL subwoofers.Drawing too much power at 1 ohm. Trying to wire to higher ohm just not positive how to.Wanting a second opinion.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 77 Answers

A good resource for wiring and information on the web can be found at 12volt.com

Posted on Feb 18, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hot to wire a pioneer premier TS-W3004SPL dual


Check crutch fields website for sub wiring.

Sep 03, 2014 | Car Speakers & Subwoofers

1 Answer

Wire 2ohm or 4 ohm


wiring depends on what amplifier you're using..

Dec 28, 2013 | Pioneer TS-W3004SPL Car Subwoofer

1 Answer

How do I wire my 12inch mtx ts 55 subwoofer two outlets red with red and black with black or red and black and red and black


The TS55 is a DVC subwoofer that can be wired for either 4 ohms (voice coils in series) or 1 ohm (voice coils in parallel). The appropriate wiring depends on the amp.

If the amp is stable at 1 ohm, wire both positives and both negatives to the matching amp output terminal (parallel) as shown in Wiring Option #1.

If the amp isn't stable at 1 ohm, connect a jumper between the positive on one voice coil and the negative on the other voice coil. Then connect the remaining positive and negative to the matching amp output terminal (series) as shown in Wiring Option #2.

http://www.rockfordfosgate.com/rftech/woofer_wizard.asp?submitted=true&woofer_qty=1&woofer_imp=3

Jun 17, 2011 | MTX TS551022 Car Speaker

1 Answer

I cannot find the right way to hook my TS-W304C Subwolfers up to a mono channel amp.


what amp? the speaker wiring depends on the ohmage rating of the amp. if the amp is 2 ohm stable, then you can hook 2 TS-W304C's up to it, both positive leads from the speakers attached to the amp positive, and both negative speaker leads connected to amp negative. this is called parallel wiring, and it reduces the ohmage (resistance) down to 2 ohms. your speakers are 4 ohms, and 2x4 ohm speakers in parallel makes it equal 2 ohms. if your amp is only 4 ohm stable, then you will only be able to hook up one of your speakers to it.

Mar 13, 2011 | Pioneer TS-W304C Car Subwoofer

1 Answer

Pioneer ts-w3001d4 burning smell


Any burning smell, is a sure sign of a short circuit, if you are unable to physically dismantle the unit, my STRONG suggestion is to replace it ASAP.

I have heard of (not experienced) short circuits causing localised wiring damage, and too the extreme fires,

I hope this helps

Please vote if you liked this response

Jun 18, 2010 | Pioneer TS-W3004SPL Car Subwoofer

1 Answer

I have the Pioneer Champion series 10" sub I believe its the TS-W3004SPL I have to look at the box. But I was driving friday morning and my sub started to go in and out and then i started smelling a...


Yes - your voicecoil is damaged.
The smell you experienced was the protective rosin around the voicecoil melting.
Fading in and out is likely the amplifier's protection when the subwoofer's coil grounds out to the polepiece.

Check the impedance of each coil using a multimeter. this will give you a definite answer if the coil is in fact blown.

Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question.

May 17, 2010 | Pioneer TS-W3004SPL Car Subwoofer

1 Answer

How to wire the Pioneer Premier 12in. dual 2 ohm voice coil. 1000 watt rms 3500 watt peak, and I have a 1000watt JL audio 2 channell amp, they are both stable at 1 ohm. I wired them parrallel, and it blew...


If you have two subs to connect, place the speakers next to each other face down, you will notice that the connection points run in sequence +- and +-. Now connect the - (negative) from the one speaker, to the + (positive) of the other speaker. Now connect the open + from the one speaker and the open - from the other speaker to your amp.
If you have only one speaker it should be bridgeson your amp.
Your amp should have a bridging indication. On the connection points of each channel on the the amp, you should see a mark pointing to the first - and the last +. That will be your bridge

May 09, 2010 | Pioneer TS-W3004SPL Premier 12" SPL...

1 Answer

Connection Pioneer TS-W65A


you are probably looking at a dual voice coil subwoofer. This means you have many options of wiring in series/parralel/or bridged parralel. Go to either www.the12volt.com or crutchfield's learning center in order to figure out what your options are. Then you need to find out what ohm your subwoofers and what ohm your amp is stable at.

May 05, 2009 | Pioneer TS-WX65A Car Speaker

2 Answers

Subwoofer wiring diagram


parallel wiring. hook all 4 positives together and run to the positive output from the amp, hook all 4 negatives together and run to the negative output from the amp.

hope this helps,
trin

Nov 19, 2007 | Car Speakers & Subwoofers

Not finding what you are looking for?
Pioneer TS-W3004SPL Car Subwoofer Logo

Related Topics:

688 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pioneer Car Speakers & Subwoofers Experts

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

yadayada
yadayada

Level 3 Expert

60867 Answers

Pablo Gonzalez

Level 3 Expert

733 Answers

Are you a Pioneer Car Speaker and Subwoofer Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...