Question about Samsung HLR5067WX 50" Rear Projection HDTV

1 Answer

How to change ballast in zenith rear projection tv model D52WLCD

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

WRONG TV -SORRY

Posted on Feb 19, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I got a 52" zenith


No,the tv message said replace lamp wright?Yes,mean the tv projection lamp is the causes and the problems.The tv projection lamp life span have ended that why the tv it is not holding a stable tv projection lamp picture.All throught these causes,does the tv make alot of clicking noises too,when the tv projection lamp is it on for 30 sec.and shut it self off?Yes,than the board that call the Ballast board it is also dead too.This Ballast board only job are to ignite the tv projection lamp only.Tries websites like Partstore.com,Ebay.com to buy a new tv projection lamp and a new Ballast board too for the replament too,if this tv causes have alot of clicking noises,when the tv is trying to ignite the tv projection lamp.

Aug 09, 2011 | Zenith D52WLCD 52" Rear Projection...

1 Answer

I need buy one lamp tv zenith d52wlcd. where can i buy this lamp? please !!!! thanks


Try this. Type in the model number on Amazon. That is where o ordered mine

Jul 23, 2011 | Zenith D52WLCD 52" Rear Projection...

1 Answer

TV turned off, red and green lights flash for 60. Changed lamp STILL NOT WORKING. Question: Should you still hear the TV if the lamp was out?


Yes,u still can hear sound,if the projection bulb is dead.The Ballast board might also dead dead too.The Balllast board help to ignite the projection bulb.

Jul 14, 2010 | Zenith D52WLCD 52" Rear Projection...

1 Answer

I have a Zenith d52wlcd and the screen is dark or excessively blue.


Go to the Zenith repair site. This has been resolved in a lawsuit. Zenith will fix it free of charge through 7/1/2010. The shop just picked my up to replace the light engine free of charge. Call 1-800-228-1757, have your model number and serial number, and where you purchased it. Here's the neat thing-the question I asked is "have they fixed the problem with the light engine, or is it going to keep going bad?" If happens again (blue lines/spots) before 7/1/2010, they'll replace the TV with a new and different TV of equal value!

Jun 27, 2009 | Zenith D52WLCD 52" Rear Projection...

1 Answer

Rear Projection TV shuts down after a few minutes.


My science teacher had the same problem.
After, he replaced the lamp it stoped over heating.
witch is most likelywhy the tv is over heating

Jan 21, 2009 | Zenith D52WLCD 52" Rear Projection...

1 Answer

Rest lamp timer zenith


Hold mute on the remote and enter on the front panel of the tv simultaneously for 5 seconds. Make sure the remote is getting signal to the TV. This works on newer model zenith and lg digital projections.

Dec 07, 2008 | Zenith D52WLCD 52" Rear Projection...

1 Answer

Where Is the Ballast.


The ballast is on the other side of the lamp compartment. the lamp plugs into the two short leads that are attached to the ballast. Its a small circuit board.

Jun 13, 2008 | Zenith D52WLCD 52" Rear Projection...

1 Answer

ZENITH D52WLCD


I just found the solution on another model of Zenith TV. Hold the enter button down on the TV and the MUTE button on the remote. In approx. 5-7 seconds a screen will pop up asking if you want to reset the lamp timer. Hit the bullseye button in the middle of the arrows and it will reset. Worked perfectly.

Apr 15, 2008 | Zenith D52WLCD 52" Rear Projection...

1 Answer

Changed Lamp, But not as bright as before!!


Just had that problem wrong lamp used orignal lamp fixed problem

Feb 21, 2008 | Zenith D52WLCD 52" Rear Projection...

1 Answer

D52wlcd


I was watching a movie and the screen went black i do have sound. what it can be?

Sep 11, 2007 | Zenith D52WLCD 52" Rear Projection...

Not finding what you are looking for?
Samsung HLR5067WX 50" Rear Projection HDTV Logo

Related Topics:

30 people viewed this question

Ask a Question

Usually answered in minutes!

Top Samsung Televison & Video Experts

The Knight
The Knight

Level 3 Expert

72601 Answers

Henry  Thomas
Henry Thomas

Level 3 Expert

1074 Answers

Jerry Greenberg
Jerry Greenberg

Level 3 Expert

1667 Answers

Are you a Samsung Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...