Question about Hoover AAA160 Front Load Washer

Open Question

Users Manual/ Hoover Performa AC121 washing Machine

Hi..do you have a Users Handbook for a Hoover Performa AC121 Washing Machine....?

Posted by on

6 Suggested Answers

  • 209 Answers

SOURCE: how to use hoover ac121

normally the numbers are the same for all uk machines, if the previous washer you used had numbers on it, just remember them and use them as you would, so if a number 2 was a 90 degree boil wash them it would be the same number for all uk machines, that is my experience, or older machines had letters example letter D = non fast coloureds

Posted on Sep 02, 2007

murdozzz2
  • 75 Answers

SOURCE: washing machine wont empty

hi there this is a common fault empty the water into a bucket and remove the water pump to check for blockages, the pump is located at the rerar lefthand side of the w/m.
also check your drain hose where it connects under your sink.

hope this helps

Posted on Dec 11, 2007

jmeredith
  • 417 Answers

SOURCE: hoover performa 1100 ac110

hi,
unplug it
try and take the drain hose out of the wall drain and get it as near to the floor as possible into a bucket, maybe let it hang out the door on the ground, gravity should let the water drain out, If its a new type it may not work though but you can try that.

good luck

J

Posted on Jul 16, 2008

  • 1 Answer

SOURCE: I need to download hoover washing machine manual HNWL7146-80

You can try going to http://www.managemyhome.com/ and looking up the model # there.

Posted on Mar 15, 2009

  • 12 Answers

SOURCE: Can you please help me, i need a users manual for Washing machine

download from whirlpool.com

Posted on Mar 27, 2009

blueextc3221
  • 15935 Answers

SOURCE: Hoover Performa 1100 WA110-001 washing machine

1. Find out where the leak is coming from. Does it leak constantly or during one part of the cycle?
A constant leak means the leak is in the valve where the hoses hook to the washer, the supply valves, or the lines to the washer from the water supply.
The other two options are when the washer is agitating or pumping the water out between cycles.


2. See if it leaks during both cycles and the test there would be to lift the lid just as it starts to drain and wait to see if the water stops leaking.
If it doesn't, then run the drain cycle to see if it gets worse or better.
Results may not be immediate as it would take a few minutes for whatever water there to finish dripping.


3. Wait until the water has been pumped out, lift the lid and check the drip again.
When the location of the leak has been determined, unless the washer has been frozen, most leaks can be fixed without parts and just using hand tools.
If you have an older, top load washer, the back or front will come off so you can observe where the leak is coming from.

WARNING. You are working with a moving, electrically hot machine that could flood.
You must take your time and not put your hand or hair in somewhere that can catch you.
You should not have to get into the upper control center, thus reducing the shock hazard.

4. Before turning the machine on, remove a cover. On some washers, there are two screws on the bottom L & R front corners that take the front panel loose.
Once the screws are removed, the front cover is hinged at the top and you simply pull the bottom away from the machine until it comes un-hooked, and set the cover aside.

There shouldn't be many exposed wires or ends, but a few. Don't touch the terminals or lay something metal in the machine that could fall on the terminals.


5. Take a flashlight, look for obvious leaks or better, water stains around nuts, hose clamps, etc.
Most likely you'll see some water residue here and there and that would be normal as a washer is wet. Look for puddles, long white streaks, calcium deposits.
Most likely, you won't find standing water, but some clues of where you should look when the machine is running.
Unless this leak is so obivous you can see what's wrong, you don't need to start it and you should repair the problem.
Once possible areas have been identified, you should start the machine as if you had a load in it and start to watch for the leak.

WARNING- Make sure you have no tools laying in the machine and you are out of the way. There are spinning parts and live wires once you turn the machine on.
Stay clear, and watch your hair and hands.

Once the machine is full and starts its cycle, look for leaks.
Let the machine do its cycle and as it goes into each part of the cycle, look for the leak.
Once you find a drip, stop the machine by lifting the lid or pulling out on the control knob, and now observe more closely.
Remember, water runs down; where it drips is not necessarily the place of origin.

6 Find the leak and make the needed adjustment (which will be all that is necessary most of the time).
If it is a part you need, get the make, model number and serial number of the washer and call an appliance parts dealer or repair service if you don't think you can repair the problem.



If the washing machine leaks water while it is filling, pull it away from the wall and see if the water drips from the inlet hoses or valves as the unit fills.
If it does, tighten the faucet packing nuts. Then, inspect the hoses and replace them if they have become cracked.
Also look for cracks in the casing of the inlet valves. Unplug the unit and lift the top to better inspect the valves.

Replace any valves that are cracked.

Valves usually crack when the hot water in the house water supply is heated to greater than 170 degrees.
They also crack if the house is left cold during the water and water is not drained from the unit. A cracked inlet nozzle can leak during fill.
The leaking water will drip down the outside of the tub and collect under the unit. Be sure that the hose connected to the inlet nozzle is tightly clamped.
Replace the nozzle if you find cracks in it.

If the leaking occurs at some time during the wash sequence other than when the machine is filling with water, unplug the unit, remove the back panel and examine the parts under the machine.
You can make a closer inspection by tipping the unit over onto it's front or side.

Tighten hose clamps that have become loose. If water is leaking from the pump, replace the pump.

The gasket between the tub and the splash guard may wear out and leak. To check the gasket, lift the top and remove the snubber and splash guard.
Replace a worn gasket. A hole in the bottom of the tub can develop.
If the hole is less than 1/4 inch in diameter, remove the agitator and basket and seal the hole.
If the hole is larger, replace the washing machine or tub.




Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question

Posted on Sep 14, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hoover performa 900 model number washing machine user guide


Check out this site and see if you can find your model number of your machine.....http://www.whitegoodshelp.co.uk/washing-machine-instruction-books-and-user-manuals/

Aug 25, 2014 | Washing Machines

2 Answers

When I switch on the On/Off button the machine trips the mains electricity. It is a Hoover Performa 1100 Washing Machine


Hi from retired Englishman in SW France,

Sorry but with such a major fault it is virtually impossible for anybody on this forum to remotely guess what is wrong with your washer.

It could be internal wiring/plugs sockets, control panel switches, control PCB, water inlet control valves, door solenoid as primary suspects. Secondary suspects could be main motor, drain motor.
I fear that you only real option is a service call as the engineer will have the right equipment to safely diagnose what is wrong.

Sorry again and good luck,
John C

Mar 09, 2011 | Hoover Washing Machines

1 Answer

User manuual


go here they will give it to you free http://service.hoover.co.uk/manuals/
hope this helps please remember to rank how this helped you and if i can answer any further questions please write back otherwise have a great day

Aug 01, 2010 | Hoover AAA140 Front Load Washer

1 Answer

I have a hoover performa ac 121 washing machine and i dont know what numbers on the machine are for which wash, can you help?


here is an information about your washing machine
http://www.partmaster.co.uk/cgi-bin/m-catalogue.pl?brand_ref=76&mtype_ref=287&model_ref=18517

Sep 23, 2009 | Washing Machines

1 Answer

Hoover performa 1200 bangs when spinning.


it sounds like you spider as broke you will need a new drum as they are not bolted on

Jun 21, 2009 | Kenmore 24872 Top Load Washer

1 Answer

User guide for hoover performa eco 1200


http://service.hoover.co.uk/manuals/Manuals.aspx?Section=10

go to that website to get an online manual for any hoover machine. the performa eco is a WB120.

Mar 26, 2009 | Washing Machines

1 Answer

I am looking for the instruction manual for the hoover performa eco wb120 washer dryer as i cant seem to spin my washing which is stuck in the machine


My partner fixed this problem by taking the machine back out and found that the connection to the water outlet pipe under the sink had a buung left in so after it was removed my machine drained

Mar 22, 2009 | Hoover Washing Machines

1 Answer

Washing machine problem


I have a performa 1100. No 4 is the 40 degree is the normal cottons cycle which is the one I use. Tip- only fill the drum 3/4 full otherwise it struggles to drain and spin- I know!

Jan 21, 2008 | Hoover PE235 Front Load Washer

1 Answer

Washing machine wont empty


hi there this is a common fault empty the water into a bucket and remove the water pump to check for blockages, the pump is located at the rerar lefthand side of the w/m.
also check your drain hose where it connects under your sink.

hope this helps

Dec 11, 2007 | Washing Machines

2 Answers

How to use hoover ac121


normally the numbers are the same for all uk machines, if the previous washer you used had numbers on it, just remember them and use them as you would, so if a number 2 was a 90 degree boil wash them it would be the same number for all uk machines, that is my experience, or older machines had letters example letter D = non fast coloureds

Aug 30, 2007 | Hoover Nextra HNWL 3136 Front Load Washer...

Not finding what you are looking for?
Hoover AAA160 Front Load Washer Logo

Related Topics:

609 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hoover Washing Machines Experts

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Gerry Harvey
Gerry Harvey

Level 3 Expert

1456 Answers

Chris Hall
Chris Hall

Level 3 Expert

842 Answers

Are you a Hoover Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...