Question about Riccar 8650/8625 s Vacuum

3 Answers

Changing Belt on Riccar 8650

I need to find instructions on how to change a belt on a Riccar 8650. I can't find my manual and can't find any info on line.

Posted by on

3 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 438 Answers

Greetings from GoVacuum,

I will attempt to walk you through the belt change on your Riccar 8955 upright vacuum cleaner. I have taken pictures for you for each step to ensure that it's done properly. What you'll need to have handy for this repair;

- Phillips Head Screw Driver
- Riccar 4000 / 8000 Series Belt
- Riccar 8000 Series Roller Brush With Clutch Assembly (only if the brushes have worn down, not necessary if brushes are still long)

Step 1: Make sure the vacuum cleaner is unplugged, and turn the vacuum cleaner upside down so the bottom plate is upwards. It's easiest to do on a work bench or counter top.


Changing Belt on Riccar 8650 - bbed7f9.jpg

Step 2: Unscrew the two metal screws on the metal bottom plate with your Phillips head screw driver, and remove the bottom plate from the vacuum cleaner so the belt is completely exposed with the roller brush


Step 3: Remove the belt guard that sits to the left of the roller brush, and is a metal part that protects any dirt & debris from going over to the belt. Here's a picture of that part being removed;
011205a.jpg

Step 4: Remove the Rug / Floor actuator arm from the clutch on the right hand side of the roller brush. Simply pull the metal actuator arm to the left of the brush and out of the circle that it sits in. Here's a picture of that;

Changing Belt on Riccar 8650 - 0a5aafc.jpgttp://i.fixya.net/uploads/images/0a5aafc.jpg" alt="0a5aafc.jpg" class="h_mi" />

Step 5: Once you have removed the actuator arm for the clutch, as well as the belt guard, lift straight up on the roller brush and remove the roller brush from the vaChanging Belt on Riccar 8650 - d6b6384.jpgr:


d6b6384.jpg
Step 6: Once you have removed the roller brush, and the old belt from the vacuum cleaner, take one new belt and wrap it around the metal pin in the back of vacuum cleaners agitator housing. Here's a picture of where that pinChanging Belt on Riccar 8650 - c0bc5cf.jpg with the belt wrapped around it;


c0bc5cf.jpg
Step 7: Once you have the belt wrapped around the metal pin (this is the shaft to the motor that actually spChanging Belt on Riccar 8650 - 1e0386b.jpgt), but the other end of the belt through your new roller brush;


1e0386b.jpg
Step 8: There is a specific way that the roller brush has to be inserted. If the roller brush is not put in properly, this can cause all sorts of problems including the brush not spinning, and continuously having to replace belts. You can see on the end cap of the roller brush (the right side where the belt rides)Changing Belt on Riccar 8650 - 04e3743.jpg is two little teeth that protrude out of the end cap as well as an indentation on the opposite side;

04e3743.jpg
Step 9: With the roller brush inserted through the belt, position the two teeth facing downwards. You can see in the vacuum cleaner where the roller brush sits, a little groove down inside of the housing. These two teeth need to straddle that groove. Also make sure that the little ring, or circle that the clutch actuator arm sits into, is facing upwards completely. It should be directly on top of the two teeth. Stretch the belt using the roller brush as leverage down into the agitator housing of the vacuum cleaner, making sure that the two teeth are facing downwards straddling the little groove. After the brush is back inChanging Belt on Riccar 8650 - 88581e1.jpgum cleaner, take the metal actuator arm from the rug / floor switch, and insert it back into the metal ring (or hole) on the roller brush;
88581e1.jpg
Step 10: Replace the metal belt guard that rests to the left of the belt. You'll notice on the belt guard that thChanging Belt on Riccar 8650 - dfaabe8.jpg little 90 degree notches on both sides. These notches need to face towards the belt or to the right. Here's a picture of the belt guard being put back into place;

dfaabe8.jpg

Step 11: After inserting the belt guard back into the vacuum, turn the vacuum cleaner oChanging Belt on Riccar 8650 - 8cd34ee.jpgtop of the agitator housing is facing you. Change the the rug / floor switch from bare floors to the carpet setting, and the turn the vacuum upside again so the brush and belt are exposed:


8cd34ee.jpg
Step 12: With the vacuum set to the carpet setting, pull the belt forwards to ensure that the brush is spinning freely. If the belts do not spin freely, repeat steps 2-10.

d433465.jpg
Step 12: There is a flap that can be opened after the metal bottom plate has been removed, that will give you more access to the motor shaft. Make sure that this flap is closed;

e6dde78.jpg
Step 13: The last tricky part can be reinstalling the metal bottom plate. There is a little lip on the front of the vacuum cleaner that the edge of the bottom plate hasChanging Belt on Riccar 8650 - a34ed7a.jpgnder for it to be installed properly. A lot of people just install the bottom plate over top of this lip, and this prevents the brushes from hitting the carpet as low as if the bottom plate is correctly installed. Here's a picture of the lip with the bottom plate in the backgroud;


a34ed7a.jpg
Step 14: Slide the metal bottom platChanging Belt on Riccar 8650 - fc1c13a.jpglip on the vacuum cleaner, and fasten the screws back into the bottom plate to secure it. The lip is a little tricky, but after doing it Changing Belt on Riccar 8650 - 570c909.jpgyou'll have no problems in the future changing your belt.

Here's a picture of the bottom plate installed INCORRECTLY with the bottom plate over top of the lip;

fc1c13a.jpg
Here's a picture of the CORRECT way to install the bottom plate:


570c909.jpg
I hope that this repair solution is helpful to you in installing the belt properly. If you found this helpful, please be sure to click the 4 Thumbs Up Icons in the top right hand corner of the solution. Feel free to request a clarification of the repair if you have any questions about this repair, or other repairs. I'm always happy to answer any questions.

Thank you very much,

Chris J.

Posted on Mar 21, 2010

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Don't know where to tell you this but you were a great help putting the belt back on right so it worked. I thank you very much. dorothy tretter

Posted on Dec 08, 2011

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Expert
  • 76 Answers

Go on their website, type in the model, and see if you can download the manual.

Posted on Jul 30, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Riccar 8625 doesn't seem to beat carpet but the brush is turning


Your 8625 is well over 20 years old. If it's been over a year since you've replaced the belt start with a new belt. Belts lose elasticity and should be replaced at least once or twice per year. The brush roll will still spin and appear to be working fine but when you put the brush roll onto the carpet it will stop spinning fast enough to clean the carpets.

Jan 25, 2014 | Riccar 8650/8625 s Vacuum

1 Answer

How to install belt on Riccar 8750 commerical vacume cleaner?


No. There is only one belt. Remove the bottom plate to gain access to the belt.

Jan 18, 2014 | Riccar 8650/8625 s Vacuum

1 Answer

Troubleshooting


There is a clutch on one side of the carpet head of the vac, which needs to be moved to one direction or the other. Your instruction manual should be able to tell you which way is which. This lever in turn activates a cam to tighten a clutch plate to the end of the brush roll. Try that and get back to me.

Nov 11, 2013 | Riccar 8650/8625 s Vacuum

1 Answer

I need to replace the belt on my Riccar supralite vacuum and need instructions


Lay the vacuum upside down, remove the bottom plate, remove the brush roll and belt, install new belt around motor shaft and brush roll, pull on brush roll to stretch belt far enough to drop brush roll back into place.

Aug 14, 2013 | Riccar 8955 Upright Vacuum

1 Answer

How do I replace the belt on my ricaar model 8750 vacuum?


Remove the bottom plate to access the brush roll. Remove the brush roll to install a new belt. Your
model is over 20 years old. If it has never been Professionally serviced it may be wise to take it to a Riccar dealer for service. It could add many more years of life to your vacuum.

Jul 23, 2011 | Riccar 8650/8625 s Vacuum

1 Answer

NEED ASSISTANCE ON INSTALLING BELT FOR MODEL 8625


HI There,

Here's a link that will walk you through step by step on how to replace the belt on your Riccar 8625 upright. This is an almost identical model, and the belt change is identical to yours.

If you have any questions please feel free to add a comment on the repair, and I"ll be happy to follow up and answer any of your questions.

Please rate my repair or send me feedback if this helped you,

http://www.fixya.com/support/t4184186-replace_belt_riccar

Thanks,

Apr 20, 2010 | Riccar 8650/8625 s Vacuum

1 Answer

Won't pick up dirt and hard to push


Hello,

This sounds like it is most likely a belt issue with your Riccar. In order to verify this, turn the vacuum on and turn it over on it's side after making sure that the carpet / floor switch on the top of the roller brush housing is turned to Carpets.

When you turn the vacuum on after changing the switch to carpet mode, does the roller brush spin? The belt controls the the roller brush and makes it spin. When the belt is broken or stretched out, and the brush is not spinning, or stops as soon once it hit carpeting, the brush roller will no longer help pull the vacuum forward. This would explain why the vacuum is very hard to push.

In order to help you the best, I went ahead and took some pictures for you on how to change the belt. The only really tricky part is the clutch actuator arm. If you don't already have a new belt, here's a link for you to a 2 pack of belts for your 8955 on our website:
Riccar 4000 / 8000 Series Upright Belts (2pk)

The model that I took pictures of is actually a model 8650, but this is identical in every way to your 8955 in terms of changing the belt.

What you'll need to have handy for this repair;

- Phillips Head Screw Driver
- Riccar 4000 / 8000 Series Belt
- Riccar 8000 Series Roller Brush With Clutch Assembly (only if the brushes have worn down, not necessary if brushes are still long)

Step 1: Make sure the vacuum2_bing.gif cleaner is unplugged, and turn the vacuum cleaner upside down so the bottom plate is upwards. It's easiest to do on a work bench or counter top.


485aeb8.jpg
Step 2: Unscrew the two metal screws on the metal bottom plate with your Phillips head screw driver, and remove the bottom plate from the vacuum cleaner so the belt is completely exposed with the roller brush.

Step 3: Remove the belt guard that sits to the left of the roller brush, this is a metal part that protects any dirt & debris from going over to the belt. Here's a picture of that part being removed;



Step 4: Remove the Rug / Floor actuator arm from the clutch on the right hand side of the roller brush. Simply pull the metal actuator arm to the left of the brush and out of the circle that it sits in. Here's a picture of that;

fa36553.jpg

Step 5: Once you have removed the actuator arm from the clutch, as well as the belt guard, lift straight up on the roller brush and remove the roller brush from the vacuum cleaner:




Step 6: Once you have removed the roller brush, and the old belt from the vacuum cleaner, take a new belt and wrap it around the metal pin in the back of the vacuums agitator housing. Here's a picture of where that pin is located with the belt wrapped around it;

f76bd31.jpg


Step 7: Once you have the belt wrapped around the metal pin (this is the shaft to the motor that actually spins the belt), put the other end of the belt through your roller brush;

68efbd6.jpg


Step 8: There is a specific way that the roller brush has to be inserted. If the roller brush is not put in properly, this can cause all sorts of problems including the brush not spinning, as well as continuously having to replace belts. You can see on the end cap of the roller brush (the right side where the belt rides) that there are two little teeth that protrude out of the end cap. Here's a picture of how it looks:

96719f8.jpg

Step 9: With the roller brush inserted through the belt, position the two teeth facing downwards. You can see in the vacuum cleaner where the roller brush sits, a little groove inside of the roller brush housing. These two teeth need to straddle that groove. Also make sure that the little ring, or circle that the clutch actuator arm sits into, is facing upwards completely. It should be directly on top of the two teeth. Stretch the belt using the roller brush as leverage down into the agitator housing of the vacuum cleaner, making sure that the two teeth are facing downwards straddling the little groove. After the brush is back into the vacuum cleaner, take the metal actuator arm from the rug / floor switch, and insert it back into the metal ring (or hole) on the roller brush;

837f4a1.jpg

Step 10: Replace the metal belt guard that rests to the left of the belt. You'll notice on the belt guard that there are two little 90 degree notches on both sides. These notches need to face towards the belt or to the right.

Step 11: After inserting the belt guard back into the vacuum, turn the vacuum cleaner over so the top of the agitator housing is facing you. Make sure that the rug / floor switch set to the carpet setting again, and then turn the vacuum upside down again so the brush and belt are exposed again.

Step 12: With the vacuum set to the carpet setting, pull the belt forwards to ensure that the brush is spinning freely. If the belts do not spin freely, repeat steps 2-10.

f8f8407.jpg

tep 13: The last tricky part can be reinstalling the metal bottom plate. There is a little lip on the front of the vacuum cleaner that the edge of the bottom plate has to slide under for it to be installed properly. A lot of people just install the bottom plate over top of this lip, and this prevents the brushes from hitting the carpet as close as if the bottom plate is correctly installed. It will take away the vacuums cleaning cleaning ability dramatically. Here's a picture of the lip with the bottom plate in the backgroud;

Step 14: Slide the metal bottom plate into the lip on the vacuum cleaner, and fasten the screws back into the bottom plate to secure it. This is the way it will look if the bottom plate is installed the WRONG way.

381c631.jpg

Here's a picture of the RIGHT way to install the bottom plate:

0b3129c.jpg

The Riccar 8955 is great vacuum, and cleans better then most other upright s when it has a new belt on. I hope that this repair solution is helpful to you in fixing your vacuum. If you did, please be sure to click the Thumbs Up Icons in the top right hand corner of the solution. Feel free to request a clarification on the repair if you have any questions. I'm always happy to answer any questions. I hope will consider GoVacuum.com storefront for any Riccar supplies that you may need. We carry all Riccar Vacuum Bags, Filters, Belts, and Parts.

Thank you very much,

Chris J.
GoVacuum

Apr 03, 2010 | Riccar 8955 Upright Vacuum

Not finding what you are looking for?
Vacuums Logo

511 people viewed this question

Ask a Question

Usually answered in minutes!

Top Riccar Vacuums Experts

Roger Potts

Level 3 Expert

694 Answers

Les Dickinson
Les Dickinson

Level 3 Expert

18330 Answers

Jim Parker
Jim Parker

Level 3 Expert

1040 Answers

Are you a Riccar Vacuum Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...