Question about Hotpoint First Edition WMA22 Front Load Washer

1 Answer

Hotpoint wma22 fills with water but won't wash or spin

Recently our machine stopped mid cycle.
When you turn the machine on it will fill with water, and the drum will rotate several times and it ends the program.
The same thing happens when you put it on a spin cycle.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Suspect motor brushes need replacing.
Simple task accessed by removing the top of the washer and releasing the clips holding the brushes into the motor - clip on back of brush - to remove the brush assembly.
Replace complete brush assembly.

Posted on Feb 16, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Forty cycle takes some water in then stops


Beko WM5100W Washing machine wash/spin problem ...

? 3:59
https://www.youtube.com/watch?v=rih6H1cpu9Q
Jun 12, 2012 - Uploaded by ilona ilona
problem in washing cycle. fast spin for few seconds and cut off .... I have same machine, it starts up fills half way with water then stops :'.

Washing machine stops mid cycle - White Goods Help

www.whitegoodshelp.co.uk > ... > DIY Washing Machine Repair Help

Jan 10, 2016 | Beko Wm & Wma Models Washing Machine Motor...

2 Answers

Our hotpoint wma22 does not fill as cloths come out dry. How can we fix this


check ur water hose line from the home, the water inlet valve itself , and the water pressure switch

Jul 10, 2014 | Hotpoint First Edition WMA22 Front Load...

2 Answers

My Hotpoint wf000 1000 spin model won't spin. It goes through a full wash cycle, agitates fine, but just won't spin at the end of the wash. Any help appreciated.


Sorry if it may be too obvious, but have you checked the philtre? generally they stop spinning when it's stuffed... when you open it, make sure you have a mop and bucket handy, some water will come out!

Nov 06, 2012 | Washing Machines

1 Answer

Fills when not being used


where the water pipes plugs into machine it has a water stop valve there. turn water off at mains and unscrew pipe. it may have a blockage of some sort keepng the valve open. hope this helps

Feb 14, 2012 | Hotpoint First Edition WMA22 Front Load...

1 Answer

Our hotpoint WMA22 washer will fill with water and wash but will not drain.i have lowered the drain hose to almost ground level and it will empty the water, and then will spin. In your opinion is it the...


Sounds like a blocked filter to me.
Remove lower rear panel of washer, remove large black hose fastened to bottom of drum, remove and clean filter inside hose, check pump for blockage at same time. You probably will not need to replace any parts
Please rate my solution.
Thanks.

Nov 06, 2009 | Hotpoint First Edition WMA22 Front Load...

1 Answer

Stops in the middle of wash cycle


Hi!

If the cycle doesn't advance, it's probably the timer or a cold-water supply problem:
It's the timer, if your washing machine fills with water and begins agitating, but the timer never advances--or if the washer is in a spin cycle and the timer won't advance. Then you need to replace the timer.
It may be a cold-water supply problem, if the washing machine fills with water, agitates, drains, and spins, but then doesn't fill with rinse water. See There's no cold water.
Please do rate this solution as FixYa and revert for further assistance.

Thanks
Rylee

May 29, 2009 | Whirlpool Ultimate Care II LSQ9549L Top...

1 Answer

Washing machine stops on spin cycle


You need a new drain pump.

May 04, 2009 | Washing Machines

2 Answers

Washer will fill fill with water but doesn't start wash cycle


it will fill but won,t spin, will throw out water as if it washed, then it take water to rinse but won,t spin ,then will throw out water as if it did , but clothes are soaked

Feb 21, 2009 | Roper RAS8445KQ Top Load Washer

1 Answer

Whirlpool AWO3761 stuck mid-cycle


The cycle doesn't advanceWhen the cycle doesn't advance, it's probably the timer or a cold-water supply problem:

  • It's the timer, if your washing machine fills with water and begins agitating, but the timer never advances--or if the washer is in a spin cycle and the timer won't advance. Then you need to replace the timer.


  • It may be a cold-water supply problem, if the washing machine fills with water, agitates, drains, and spins, but then doesn't fill with rinse water. See There's no cold water.

  • Jul 06, 2008 | Whirlpool AWM6100 Front Load Washer

    Not finding what you are looking for?
    Hotpoint First Edition WMA22 Front Load Washer Logo

    Related Topics:

    258 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Hotpoint Washing Machines Experts

    hungoverrr

    Level 1 Expert

    5 Answers

    puggy666

    Level 1 Expert

    47 Answers

    gbob59

    Level 3 Expert

    2963 Answers

    Are you a Hotpoint Washing Machine Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...