Question about Nortel Meridian M7208 Corded Phone

1 Answer

My phone, a meridian M7208, does not ring incoming calls

The only phone in the system that rings is at the reception. How do I make incoming calls ring at my desk as well?

Posted by on

  • corrsol Feb 18, 2009

    following a power failure, the only phone that rings is the one in reception. light still flashes but no ringing from any other phones.

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Following a power failure, the only phone that rings is the one in reception. light still flashes but no ringing from any other phones

Posted on Jul 19, 2013

6 Suggested Answers

  • 201 Answers

SOURCE: Meridian M7208 phone

You can unplug the phone system to reset it, plug it back in and then turn off that forward rule.

Posted on Nov 25, 2007

SOURCE: MERIDIAN M7324

Do you know how to program the system?

You will need to log into system programming. Got to lines/trunks and enter your extension. You will see the line appearances to appear only. You need to change those to appear and ring.

If you do not know how to get into programming. Call a professional.

Posted on Jan 08, 2008

cnavarro
  • 2460 Answers

SOURCE: Night switching for KX-T7630

You have 4 different modes of calling available to be programmed: DAY NIGHT BREAK and LUNCH. Your installer has to set up the ICD groups, but you can create a LUNCH group which looks like the day mode but rings all phones. The codes are accessed by dialing on the intercom *780x where 0 is day 1 is night 2 is lunch and 3 is break.

You may use the NIGHT mode in the daytime, but if you have voice mail, it will play the night greeting instead of a day greeting.

Carl


Posted on Sep 09, 2008

  • 1 Answer

SOURCE: Phone will not ring

It's RINGING now! I followed the Set Programming instruction in our manual. It's in Configuration 3-21. It's a very old old Operator guide.
I am trying to find it online. In the mean time you can use the M7208 Phone Adminitration Overlay over the keys and program your phone by pressing Feature **266344
Here is a link to the overlay
Good Luck.

Posted on Feb 24, 2009

consultel1
  • 856 Answers

SOURCE: Incoming calls sound only on reception desk.

Programming2.gif is done on M7310, M7324 and T7316 sets.
To set up ringing you need to enter programming by pressing the feature key followed by **266344.When prompted to enter the password enter 266344.
The screen should say TERMINALS&SETS. The 4 top line/feature keys are now used for programming.
At the terminals&sets prompt, press the show key (top right arrow). The display should now ask for an extension number. Enter extension number you wish to program ringing on. Press the show key (top right arrow)
The display should sat LINE ACCESS
Press the show key (top right arrow) .
The display should say LINE ASSIGNMENT.
Press the show key (top right arrow) .
The display ask for a line number. press list
The display should say line 001: appear only
press the Chng key till it says appear & ring
press next key (lower right arrow)
The display should say line 002: appear only
repeat the procedure the same as line 001 for the remaining ringing lines

press the release key when finished

Posted on Nov 02, 2009

Testimonial: "Great! Very specific and easy to follow instructions. Thanks for your fast response. RO"

consultel1
  • 856 Answers

SOURCE: Norstar Meridian M7100 incoming calls - no ringing tone

Programming is done on M7310, M7324 and T7316 sets.
To set up ringing you need to enter programming by pressing the feature key followed by **266344.When prompted to enter the password enter 266344.
The screen should say TERMINALS&SETS. The 4 top line/feature keys are now used for programming.
At the terminals&sets prompt, press the show key (top right arrow). The display should now ask for an extension number. Enter extension number you wish to program ringing on. Press the show key (top right arrow)
The display should sat LINE ACCESS
Press the show key (top right arrow) .
The display should say LINE ASSIGNMENT.
Press the show key (top right arrow) .
The display ask for a line number. press list
The display should say line 001: appear & ring
press the Chng key till it says appear only press next key (lower right arrow)
The display should say line 002: appear & ring
repeat the procedure the same as line 001 for the remaining ringing lines

press the release key when finished

Posted on Jan 12, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to stop / edit all incoming calls ringing to other 2 extensions at the same time?


What phone system are you using?
I will gladly show you how

KX-TEA/TES/TA series or KX-TDA/TDE/NCP series

Oct 25, 2015 | Panasonic KX-T7633 Corded Phone

2 Answers

Remove the ringing from incoming calls on a norstar. I have multiple extensions in the building but want the incoming calls only to ring to a few extensions


You need administrative rights to get into the PBX. Once in there, you can assign which phones receive incoming calls. It has been years since I worked on the meridian system, so I can't tell you the way to do it, but it is in the manual. It's not complicated. You can also set it up for DAY/NIGHT mode so that in the evening, if required, all phones could ring on incoming calls so that anyone in the building can answer them.

Feb 04, 2015 | NorStar Meridian M7310 Phone

1 Answer

Ringer troubleshoot


Is it programmed to ring in configuration programming

Jun 05, 2014 | Nortel Meridian M7208 Corded Phone

1 Answer

My M7310 won't forward a call to the next open line but gives a busy signal


Hard to answer because your problem description does not match the part.
Nortel Meridian M7208 Corded Phone is a digital phone which works off a phone system.Also note that the carrier controls the rollover, not the phone or its system.

Once you have more/proper details maybe you can be helped.

Dec 14, 2012 | Nortel Meridian M7208 Corded Phone

1 Answer

I have a Nortel Telecom Meridian phone at work. I often get unsolicited calls on my work phone and I just want to ignore them instead of answering them. How do I mute the ringer on my Meridian phone. It...


You can use the do not disturb function on your set. When used it will stop all ringing on your set(both line ring and intercom ring). To turn on DND, press feature 85, to turn the DND back off press feature #85.

Sep 10, 2010 | Nortel Meridian M7208 Corded Phone

1 Answer

M7208n phone - mute ringer for external calls


Incoming line ring settings are in the config menu under:
2nd option - Line access
enter extension number
2nd option - Ringing
Ringing then can be toggled on or off for each line assigned to that extension.
Mark

Jul 15, 2009 | Nortel Meridian M7208 Corded Phone

1 Answer

Incoming calls briefly ring once then automatically kick over to answering machine. I cannot get any incoming calls


Are you using norstar voicemail system?

If you are and know how to get into the admin programming of it, then you go to the line programming and select the number of rings before the vmail system answers.

set the rings to "3", then the lines should ring 3 times on your phone, then on the 4th ring the vmail system will answer

Jun 26, 2009 | NorStar M7208 Corded Phone

1 Answer

I have the Nortel BCM system and the problem is with a Norstar Meridian M7208 phone. This phone randomly rings (constant rings no pause between rings) and the only way to stop it is to unplug the phone...


I had that same issue before...

I turned the:
-> Autoset Relocate to On
-> then punched the set down on another port on the BCM system

I think it's just a bad port on the system...
The swap fixed my issue at my site. It was not a set problem, just something funny from the BCM.

Not too sure if you have the means to do that swap on the system yourself. But, it can be fixed.

Mar 17, 2009 | Nortel Meridian M7208 Corded Phone

1 Answer

Doesnt ring


My BT Meridian compact does not ring after it powered down in a thunder storm. The lines flash and can be answered as normal just no ringing sound

Mar 14, 2009 | NorStar M7208 Corded Phone

1 Answer

Phone will not ring


It's RINGING now! I followed the Set Programming instruction in our manual. It's in Configuration 3-21. It's a very old old Operator guide.
I am trying to find it online. In the mean time you can use the M7208 Phone Adminitration Overlay over the keys and program your phone by pressing Feature **266344
Here is a link to the overlay
Good Luck.

Nov 19, 2008 | NorStar M7208 Corded Phone

Not finding what you are looking for?
Nortel Meridian M7208 Corded Phone Logo

Related Topics:

1,602 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nortel Phones Experts

kakima

Level 3 Expert

96372 Answers

Cindy Wells

Level 3 Expert

4753 Answers

David Burbee
David Burbee

Level 2 Expert

1868 Answers

Are you a Nortel Phone Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...