Question about Hotpoint Ariston WD440G Front Load All-in-One Washer / Dryer

1 Answer

HOTPOINT WASHER DRYER WD440G

THE WASHING MACHINE STARTS TO FILL WITH WATER THEN THE ALL THE DRYER, ANTI CREASE, LIGHTS FLASH. THE DOOR REMAINS LOCKED AND THE MACHINE WILL NOT WORK. I HAVE TO TURN OF THE POWER TO THE MACHINE TO STOP THIS
PLEASE HELP

Posted by on

  • adrian_h_jon Apr 23, 2009

    my machine sounds like its going to fill, then the reduce crease and on buttons begin to flash

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Hotpoint Master
  • 19,396 Answers

That means that the machine detected a problem at a certain point of the cycle and stopped.

If the machine stops when filling check the inlet valve and the water supply.

If it stops because ofervilling check the water level switch.

If it stops when the cycle is hot water only , then check the heating element.

If it stops when draining, then inspect drain filter, drain pump , and drain hose. You access the drain hose removing a panel at the front side of the machine.

If it stops when motor is supposed to spin faster (rinse) then it is motor control unit or motor coupler.

If it is none of the above, then it is a defective control board.


Posted on Feb 16, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hotpoint WD440 washer/dryer wont control.when plugged in 4 lights flash and it goes to pump out . no switch has any effect. the lights flashing are the on/off ,drying high heat.reduced creases and time...


The NTC for the dryer is situated on top of the dryer heater box, fault can often be caused by a simple broken wire, they are very weak at this point.

its the sensor on the dryer

if you take off the top, its mounted on top of the dryer box, usually has a white plug with 2 black wires attached

Dec 13, 2011 | Hotpoint Ariston WD440G Front Load...

1 Answer

Hi, I have a Hotpoint WD440 Wash / Dryer. When switched on at the mains electricity the "Rinse Hold, Reduce Creases, Drying Heat, time saver, dry and on/off buttons all flash for approx 5 mins, then...


The flashing lights are an error code (Which I can't quite figure, but I believe ARE associated with a blocked filter. Is it possible that the slime and mess extended beyond the filter?

Before you go throwing the machine away, Unplug it from the mains (NOT just turn it off) to allow the machine to reset and while it's unplugged, stuff your garden hose up the waste water pipe and turn it on full blast to blow any remaining debris out of the way. (Wrap a towel over the end of the pipe to soak up the spliiage as one will not fit neatly into the other).

As the Dr Pepper ad says - "What's the worst that could happen?"

Jul 07, 2011 | Hotpoint Ariston WD440G Front Load...

1 Answer

Hotpoint WD440 creases clothes badly & takes ages to dry


This sounds like excess steam in the drum. Check that the drain filter is clean as washer driers rely on cold water being taken in to cool the condenser tank during the drying cycle. If the filter is clear, the tank may be blocked with fluff. You have to open the machine a look for a big plastic tank, usually down the right hand side.

Dec 11, 2009 | Hotpoint Ariston WD440G Front Load...

1 Answer

On and off light and energy save and reduces creases lights flash


Hi Snarey, it sound like your door lock has passed away, you will need to make sure the appliance is unpluged, empty the water out of the drum, and check the vacuum switch which opperates the lock.

Mar 09, 2009 | Hotpoint Aquarius WF000 Front Load Washer

1 Answer

Hotpoint wd44d wash/dryer wont finish a wash nor wont pump out


there may be something stuck in the pump itself. hairgrips and brawires are a common find.

Jan 19, 2009 | Hotpoint Ariston WD440G Front Load...

2 Answers

Hotpoint wd440 aquarius


Not all programes fill with hot water.Try on 95 degree wash if it takes hot water ,you are dialing a prog,that does not take HOT.

Oct 31, 2008 | Hotpoint Aquarius WD63 Front Load...

1 Answer

Hotpoint aquarius wd440g washer/dryer


Hi claire your problem is the pump braking down check to make sure there is nothing in the pump if you still cant get the door open pull the mains plug out and turn off the water valves red and blue take off the top of the machine and get a basin take the drain hose out and put it in the basin and bring the two down to the floor empty all the water out you should now be able to get the door open remember to check the pump and the bearings

Jul 27, 2008 | Hotpoint Aquarius WD63 Front Load...

1 Answer

Hotpoint WD440G


I SWITH ON THE MACHINE AND F 01 APPEARS

Aug 27, 2007 | Hotpoint Aquarius WD63 Front Load...

Not finding what you are looking for?
Hotpoint Ariston WD440G Front Load All-in-One Washer / Dryer Logo

432 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hotpoint Washing Machines Experts

hungoverrr

Level 1 Expert

5 Answers

puggy666

Level 1 Expert

47 Answers

gbob59

Level 3 Expert

2963 Answers

Are you a Hotpoint Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...