Question about Classic Electronics Measuring Tools

1 Answer

Used Dario grad-o-meter D400

Does anyone know where I can find a used Dario grad-o-meter D400 (for inches). I found them brand new online but are too expensive.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I just bought a used dario gradometer and it's by inches. 8056845136 I will sell it to you.

Posted on Nov 06, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1968 Ford Ranchero


Spark Plug Gap is .032 inch. Many have started using .035 as it is easier to set using most newer tools.

Point Gap is .016 inch. You may also set point gap by using a dwell meter if you have one. That setting would be 32 degrees.

Aug 01, 2014 | Lisle 67870 Spark Plug Gauge Gap

1 Answer

How to test aa battery with greenlee dm-20


se the meter to dc volts. if is not automatic, it should be set at the 3 volt scale. Take the red lead of the meter and touch it to the positive side. The black goes on the negative side or the 'bottom, of the battery. Brand new it ill be about1.6volts+-5%. its usefullness is comprimised at 1.4 or 1.3, depending the appplication. Be sure the leads to the meter are in the correct sockets,

Mar 27, 2013 | Greenlee Dm-20 Digital Multimeter

1 Answer

Electric pre payment meter problems


deary me , my first instinct would be to contact a lawyer or the CAB, failing that this a link to the energy ombudsman paste this into your browser address bar
http://www.energy-ombudsman.org.uk/links/9-0-faqs.php

some meters do have a built in log that can be read by specialist equipment , if this is possible it will show them how much electricty youve used since your entry date ( get copys of your rental agreements for dares etc ), usually a fee is payable if your found at fault ,

i hope this helps , if it does please vote

Nov 11, 2009 | Extech EX710 800A Clamp On Electric...

3 Answers

How to mesure in feet instead of inches


Hold the POWER button down for a few seconds. Thats how you get into the settings. Cycle through options with the measure button. Use the power button to go to the next option (eg, beep on or off). Press and HOLD the power button to exit this mode.

Sep 16, 2009 | Hilti 202415 PD 4 Laser Range Meter

1 Answer

Saw blade broke. motor won't run after changing blade. reset wasn't tripped. lite still works so its not in the power cord.help! this is a craftsman 16 in. variable speed scroll saw not used very much....


It would have cost more to have Sears fix the saw than I paid for it, so I got my meter out and by checking the voltage drops across all of the electrical connections in the saw , I determined that the on / off switch was defective. This switch is the same switch used to turn the lite on and off, so I took the switch out of the lite and used it in the saw. I ordered a new switch for the lite and will install it when the new one comes. Thanks for your interest and help. fletcher1

Jul 17, 2009 | Craftsman 16" Variable Speed Scroll Saw

1 Answer

MULTIMETER USAGE


Hello,

Is this an Auto-ranging multimeter or does it have several range settings such as 2V, 20V, 200V, 750V, etc.?

If it is an auto-ranging, you will have 2 voltage selections: AC (alternating current) which will have a sine wave similar to this: ~, or DC (direct current) which will have a symbol similar to this: =. AC is mainly used to measure the voltage in your home or voltage to appliances, either 110V/120V or 220V/240V. DC is used to measure voltages such as in electronic assemblies, computers, etc.

You need to know whether you are measuring AC or DC to get an accurate reading. You also need to make sure you have the meter on a high enough range if it is not an auto-ranging meter. The best thing to do is start on a high range and work down, although most meters have an overload protection.

To measure current you must "open the circuit" and place the meter leads in the circuit. This should only be done if you are very familiar using the meter. Current is measured in Amps (A), milliamps (mA), or microamps (uA). There is little use for the common person to measure current.

Not sure what you are going to use it for. Computer power supply, perhaps?

There are some tutorials on youtube that may be beneficial. Here's one:


Here is another: http://www.youtube.com/watch?v=rivoVzxwNtI

You can do a search once there for others. Just insert "multimeter" in the Search box.

Not sure if I have answered your request sufficiently, but if you have more questions, just use the Comment button.



Jun 13, 2009 | Electric Portable Multimeter 3½ Digital...

1 Answer

Need a manual for PC omni jig- original model


You will need your model #
Here is where to get your manual

http://www.dewaltservicenet.com/

Good luck and let me know if I helped

Jan 06, 2009 | Porter Cable 55160 16 Inch Omnijig...

1 Answer

Dario Grade O Meter Instruction manual needed


Hi Tracy,

I have the book, the address in the book is Dario Grad-O-Meter 12660 Lull St. North Hollywood, CA 91605 ph (818) 765-3635

Oct 25, 2008 | Measuring Tools

Not finding what you are looking for?
Measuring Tools Logo

Related Topics:

361 people viewed this question

Ask a Question

Usually answered in minutes!

Top Classic Electronics Measuring Tools Experts

Hasan Khan Amran
Hasan Khan Amran

Level 2 Expert

180 Answers

joecoolvette
joecoolvette

Level 3 Expert

5660 Answers

Joseph Mueller
Joseph Mueller

Level 2 Expert

335 Answers

Are you a Classic Electronics Measuring Tool Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...