Question about Whirlpool Ultimate Care II LSQ9564J Top Load Washer

2 Answers

Washing machine starts by itself

My Whirlpool Gold Ultimate Care II works fine going thru the normal wash, rinse and spin cycle. After it stops for me to remove the clothes to the dryer it starts on the next cycle all by itself. ( I have to be there when the machine stops or it rotates around the knob to the next wash.)

Posted by on

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 640 Answers

Replace timer..onthejob

Posted on Feb 16, 2009

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Whirlpool Master
  • 2,651 Answers

Going through to the next wash not na normal function, perhaps the machine is advancing to an extra rinse cycle?? this EXTRA RINSE will start after the normal wash is complete, i would check your dial settings perhaps some one has mistaknely switched extra rinse "ON". if htis os not tyhe case the n i would jave to blame a faulty timer mechanism and you would need to replace the timer

Posted on Feb 16, 2009

1 Suggested Answer

mikedurland
  • 481 Answers

SOURCE: Ultimate Care II - Rinse Cycle does not start

sounds like a lid switch problem. is there a clicking noise when you open and close the lid?
if not then the lid switch may need to be replaced; inexpensive.
this could also be caused by a bad timer.
also try a different speed for the rinse cycle, it may be a bad motor and it is not going into a certain speed. instead of gentle or slow speed try fast or normal, something like that.

Posted on Jun 28, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

On the Whirlpool Gold Ultimate Care II should the "Extra Rinse" control dial control the existence of the extra rinse cycle at the end of the Normal Gentle Wash System(cycle)? The only manual I found was...



I will find my answer by testing the behavior myself. It would have been nice if you could have confirmed what I was asking. It is a complex machine, but all its behavior should be known by someone, and that is you.

Nov 15, 2009 | Whirlpool Ultimate Care II LSQ9549L Top...

2 Answers

Won't switch from wash to spin...


You have a bad motor. Your motor turns in one direction to wash and the other to spin. One directions windings are bad. This is why it is drawing currant so bad. Sorry, seems I'm always the bearer of bad news.
Please rate solution

Aug 23, 2009 | Whirlpool Ultimate Care II LSQ9549L Top...

1 Answer

Will not spin on any rinse cycle


Hi, This washer does not have a belt. While the washer is agitating, if you lift the lid will it stop? Some models will agitate but not spin if the lid is up. It sounds to me like the lid switch might be going bad.
If you will get me a model #, I can look this up for you and give you a better idea.

Vic

Jul 05, 2009 | Whirlpool Ultimate Care II LSQ9549L Top...

1 Answer

Washing machine won't rinse or spin


sounds as if you have a faulty lid switch, for safety reasons if the machine doesnt think the lid is closed it willnot spin/drain the waer out.

Feb 23, 2009 | Whirlpool Ultimate Care II LSQ9549L Top...

1 Answer

Whirlpool Ultimate Care II


sounds like a broken coupling.
it probably don't agitate either.

Oct 28, 2008 | Whirlpool Ultimate Care II LSQ9564J Top...

1 Answer

Ultimate Care II - Rinse Cycle does not start


sounds like a lid switch problem. is there a clicking noise when you open and close the lid?
if not then the lid switch may need to be replaced; inexpensive.
this could also be caused by a bad timer.
also try a different speed for the rinse cycle, it may be a bad motor and it is not going into a certain speed. instead of gentle or slow speed try fast or normal, something like that.

Jun 28, 2008 | Whirlpool Ultimate Care II LSQ9564J Top...

Not finding what you are looking for?
Whirlpool Ultimate Care II LSQ9564J Top Load Washer Logo

329 people viewed this question

Ask a Question

Usually answered in minutes!

Top Whirlpool Washing Machines Experts

Dan Webster
Dan Webster

Level 3 Expert

8147 Answers

Richard Roth
Richard Roth

Level 3 Expert

9472 Answers

Mike Cairns
Mike Cairns

Level 3 Expert

3053 Answers

Are you a Whirlpool Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...