Question about Nintendo Wii Console

2 Answers

2nd Wii remote not working

The 2nd wii remote does not seem to recognise new batteries.

I have tried putting different sets of new batteries into the remote, but the remote works for a few seconds only before the batteries apparently run out and switch the remote off.

In the Wii remote settings the battery gauge reading is low with the new batteries. When the same batteries are put into my other remote the reading is full.

Any ideas of how to resolve this issue. I've tried re-synching.

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 25 Answers

Sounds like you have a defective wii-mote to me...time to find out how that warranty / exchange program is

Posted on Feb 17, 2009

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 26 Answers

Wii Remote Syncing problem is one of the common problem of Nintendo Wii. You may check out the DIY Wii Fix Guide, that explains step by step to fix the problem without any Technical knowledge.. I hope this guide will solve your problem.. It also gives information on fixing many Wii Related Problems, so its a kind of Wii Problems Reference Fix Guide..

,

Posted on Feb 20, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2nd Wii remote not recognised when reconnecting to add player 2 on Donkey Kong. Player 2 LED comes on when resync completes but goes off when game starts.


You said when if the game starts the controller goes off.try holding the sync button on the wii console for 15-20 seconds then resync all controllers.If it doesn't work try this:Start the donkey kong game then press the home button then go to the wii remote settings it has an icon of a remote then after you enter it find the reconnect then press 1-2 simultaneously to select who is the first player.If it doesn't work try resynchronizing it as the first controller.Hope this helps.

Apr 15, 2011 | Video Game Consoles

2 Answers

2nd wii remote permanent low battery


the problem is the remote itself not the battary take it back and get a new one.

Aug 22, 2009 | Nintendo Wii Console

3 Answers

Wii remote will not work new batteries just blink all


Hey Jack, How many remotes are you able to connect at a time? If you have multiple remotes try turning the ones you know that work off, and putting them in another room(so you know they will not try to connect). Then try connecting with the bad one. If that doesn't work you might have to sync the remote: hold down the red sync button on the wii, located next to the sd card slot, while holding down the red button on the remote, located under the battery cover on the back. Now try connecting. If it still doesn't work, the LED lights in the sensor bar might have burned out, this happens a lot when you keep your sensor bar directly on your tv without the stand(the tv gets hot and burns out the lights), a lot of people do this because the stand looks bad. Go buy a new sensor bar, they sell them at wal-mart for $20, plus they're wireless, so you don't have to worry about that thin little wire popping. Test the new wii bar, if it's still not working, then you're remote is just worthy of getting returned.
hope this helps! -cj

Aug 21, 2009 | Nintendo Wii Console

1 Answer

Wii Remotes will not resync after using friends Fit Board


there is a flap in the wii open it up. open the spot where the batteries go on the controller. the controller and the wii should have a orange butten press them both at the same time.

Aug 20, 2009 | Nintendo Wii Console

2 Answers

2nd Wii remote not working this is the 2nd one


press the sync button on both the wii and the wii remote through the batt door on the remote and the button behind a door like thing next to the disk slot the blue lights flash then press wii red sync button again while pointing remote two at the sensor this should bring it on line !!!!!

Jan 01, 2009 | Nintendo Wii Console

1 Answer

New wii remote


Maybee you shou hold the red button?

Nov 08, 2008 | Nintendo Wii Console

2 Answers

Setting up 2nd wii remote


Greetings mlsaenz7,

You need to resynch the second remote to the Wii console. To accomplish this you need to hit the sync button under the battery cover on the remote, and then when the lights are flashing on the remote, you hit the sync button on the Wii. The synch button is located under the small cover to the left of the cd/dvd slot.
Thank you,

Dort
Go Ahead. Use Us.

Apr 19, 2008 | Nintendo Wii Console

Not finding what you are looking for?
Nintendo Wii Console Logo

269 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nintendo Video Game Consoles Experts

Troy Gorman
Troy Gorman

Level 3 Expert

508 Answers

phil

Level 2 Expert

567 Answers

Raj Patel

Level 3 Expert

845 Answers

Are you a Nintendo Video Game Console Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...