Question about Whirlpool Duet GHW9150P Front Load Washer

1 Answer

Error codes keeps coming up F28

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 6,784 Answers

F02 Long Drain If the drain time exceeds 8 minutes, the water valves are turned off and F02 is flashed.

Press PAUSE/CANCEL twice to clear the display.

NOTE: After 4 minutes the “Sud” error will be displayed, then 4 minutes later the F02 error code will be displayed.

Potential Causes

• Check the drain hose and make sure it is not plugged or kinked
• Check the electrical connections at the pump and make sure the pump is running.
• Check the drain pump filter for foreign objects
• If the above does not correct the problem replace the pump

Posted on Apr 02, 2009

  • Michael Masters
    Michael Masters Apr 02, 2009

    There is no (F28) code. i think you are referring to this code.

×

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have an F28 error what is wrong


As far as I know F28 error code means - SERIAL COMMUNICATIONS ERROR/MOTOR CONTROL UNIT ERROR. Caused by either a communications problem between the Central Control Unit and Motor Control Unit, or Motor Control Unit internal failure.

Jan 12, 2015 | Whirlpool Duet GHW9150P Front Load Washer

1 Answer

Whirlpool f28 error code and door lock light


For the F28 error code:
First, check the wiring harness connections to the MCU, the Motor, and the CCU. Make sure all the connections are tight and there are no ground wires off. Then check the connections of the CCU board within the housing.

If the wiring connections are fine then It would be a good idea to order both, as both components have been problematic for the error code F28.
Here is a link to the CCU.
Here is a link to the MCU.

Oct 13, 2012 | Whirlpool WFW8300SW

1 Answer

Washing stops in cycle with an F28 code.


Hi

This code indicates an electronics communication problem with the washer.Please check this link to get a detailed idea related to the lists of codes and the resolutions to them:-

http://whirlpool.custhelp.com/app/answers/detail/a_id/2885/~/display-shows-an-error-code---front-load-washer

The error code F28 means one or both of these parts are bad.
Motor Control Unit ,Microcomputer Machine Control Unit .
It would be a good idea to order both, as both components have been problematic for error code F28.

Please get back to us if you have further query or else please accept the solution.

Thanks for contacting fixya.com


Sep 02, 2011 | Whirlpool Washing Machines

1 Answer

I have a whirlpool washer & dryer Duet and my washer keeps getting an error code F21 and recently got F28. I had some work done in the laundry area which caused the washer to be moved and then put...


https://www.whirlpool.com/webapp/wcs/stores/servlet/OCManualsLiteratureSearchView?catalogId=10561&langId=-1&storeId=10211&krypto=5QgxQhneFliXuEuX564wSQ%3D%3D&ddkey=http:AjaxMiniWishListView

Above find a link to your Manual and below find a link to a Video which can assist you in fixing the F21 Error Code

The F28 Error Code could Just be a Fluke But it is supposed to mean that there is no water entering so to be sure before running another load be sure hoses are connected and turned on.

Thumbs up if Helpful and Feedback is Appreciated!!!

Jun 17, 2011 | Whirlpool Duet GHW9150P Front Load Washer

2 Answers

F 28 error code comes on


Greetings,

The f28 is a communication error...they usually happen at the right side of the drain pump where the wires go in there is a flip top cover..if its up, just push it back down and that should do it...also, if the service panel at the bottom is off..there is a panel switch that trips until the panel is put back on..this can cause an f28 as well...

If neither of these do it..just make sure all the connections are tight, again the is a communication error between boards and even the main control could be defective.

Bruce Denton

Dec 12, 2010 | Whirlpool Duet GHW9150P Front Load Washer

1 Answer

Code f28


Hi, the error code F28 means one or both of these parts are bad.
  • Motor Control Unit (8540135)
  • Microcomputer Machine Control Unit (8540788)
It would be a good idea to order both, as both components have been problematic for error code F28. If you find either the MCU or the CCU(Microcomputer Machine Control Unit) fixed it.

Oct 02, 2010 | Whirlpool Duet GHW9150P Front Load Washer

1 Answer

I washed a large load in our Whirlpood Duet Washing Machine and it stopped with a flashing F28 code. I unplugged it for 5 minutes and it still will not run a cycle without stopping with a flashing F28...


The error code F28 means one or both of these parts are bad.
Motor Control Unit (8540135)
Microcomputer Machine Control Unit (8540788)
It would be a good idea to order both, as both components have been problematic for error code F28

If you find either the MCU or the CCU(Microcomputer Machine Control Unit) fixed it.

You can download the online repair manual in the below link

https://secured.whirlpool.com/Service/SrvTechAdm.nsf/2cd44500d572193285256a45004fd9d6/6545d78b3f479480852571650061b1ba/$FILE/8178558.pdf

On page# 4-20 it shows how to access your MCU.

Jun 27, 2010 | Whirlpool Duet GHW9150P Front Load Washer

2 Answers

It was putting out a error code of f28 I changed the main board on the inside of the washer no it wont run the last spin cycle but it will do every thing else was there anything else I was supposed to do...


F28 error means the CCU(central control unit) lost communication the the MCU(Motor control Unit) for an HE2 washer.
I would look inside the lower front panel and get the tech sheet and run a diagnostic test per the instructions... See what comes up. Review troubleshooting for the F28 make sure you did not miss anything.
I hope this helps

Mar 20, 2010 | Kenmore HE2 Plus Front Load Washer

1 Answer

Whirlpool front loading washer and dryer F28 keeps coming up


F28 is a serial bus error from the CCU (Central Control Unit) to the MCU (Motor Control Unit).

All you need is some Electronics contact cleaner spray and a 1/4 inch socket to remove the top of the machine and the back of the machine.
The CCU is the computer looking box at the top front right hand corner.
Find connector M13, (has red marking on it and only 3 wires) disconnect it by pushing the retainer tab back and pulling gently on the connector.
Spray the contacts of the connector and computer with connector cleaner.
Then re-assemble connector.
The MCU is in the back lower left corner.
Find the connector with 3 wires and red mark, and remove this connector in the same way you did the other, spray it and re-install.
Put the back and top back on.

Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question!!!!

Jan 18, 2009 | Whirlpool Duet GHW9150P Front Load Washer

1 Answer

Whirlpoo; wfw9200 F22, F28, A17 A27 error codes


f22 is a door lock error and f28 is a commication error you still have warranty thorugh whirpool. you're going to need pro. help

Dec 13, 2008 | Whirlpool Duet GHW9150P Front Load Washer

Not finding what you are looking for?
Whirlpool Duet GHW9150P Front Load Washer Logo

1,217 people viewed this question

Ask a Question

Usually answered in minutes!

Top Whirlpool Washing Machines Experts

Dan Webster
Dan Webster

Level 3 Expert

8147 Answers

Richard Roth
Richard Roth

Level 3 Expert

9472 Answers

Mike Cairns
Mike Cairns

Level 3 Expert

3053 Answers

Are you a Whirlpool Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...