Question about Sony Handycam CCD-TRV87 Camcorder

Open Question

My Sony TVR-87 menu,display,date,and time does not work

Sometimes it works but most times it doesn't. The display, menu, date, time, and all buttons do not work. Also when this happens the zoom goes very slow.Any ideas what may be causing this problem.

Posted by on

6 Suggested Answers

  • 1153 Answers

SOURCE: Sony Handycam CCD-TRV37 8mm Analog... 2 Problems, maybe more unknown at this time:

I noticed on mine, I had to use small amounts of compressed air to stop it from focusing slow. Dust will do this, It has a small motor and it could be dirt slowing it down. Sounds like display problems also.

Posted on Sep 08, 2007

welcomejee
  • 10594 Answers

SOURCE: CCD-TRV228E Hi8 - how do I remove LCD date or time

You can't remove date and time stamp on recorded movie now. Go to Menu and disable date-time stamp function for future recording.
User manaul of CCD-TRV228E is availabe here...
http://support.sony-europe.com/dime/camcorders/v8c/v8c.aspx?site=&m=CCD-TRV228E&site=odw_en_GB&odw_model=CCD-TRV228E
Have nice day.

Posted on Aug 06, 2008

  • 26 Answers

SOURCE: How is the time/date stamp displayed on a copy

The time/date is 'stamped' onto the video during recording. The time/date stamp function can be turned on or off in the setup menu. If it was 'on' during recording, it will be displayed when played back. If it was turned off, it will not be seen on the recording.

Posted on Jul 24, 2009

  • 67 Answers

SOURCE: Set time and date of Handycam

hi,
its a ruttin problem you just change the LCD FLAP its easily available ,just change it and find the magic,

Posted on Aug 31, 2009

Davidivory1
  • 338 Answers

SOURCE: Sony Handycam CCD-TRV58 Hi-8 won't display picture.

This sounds like the LCD and CCT in the Lens is dead, not a cheap repair if this is the case, pop it to a camera shop like Jessops.

Posted on Jun 23, 2010

welcomejee
  • 10594 Answers

SOURCE: what would cause a sony dcr trv120 zoom button not

There is control switch block that has zoom/wide switch along with play, rewind, forward, stop, pause buttons and this switch block flip up and down while ejecting/ load tape in camcorder, this will be replaced as zoom/wide switch got defective and sending continues command of zoom to system control chip.
Let me know if you need part number of switch block control for DCR-TRV120

Posted on Jul 27, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Camcorder sony hdr-ax2000e turns itself off


hello, does it show any error code before is shuting down?

May 28, 2013 | Sony HDR Video Cameras

1 Answer

M using sony pd150, 1st problem = menu button is not working 2nd problem = sometimes viewfinder geting off 3rd problem = video in viewfinder 180 degree rotate please help me


Wow you simply have got a few snags, this camera needs a reset, press reset button, yes I know you will lose time/date but at least it will sort things.
David

Jun 24, 2010 | Sony Dvcam DSR-PD150 DV Digital Camcorder

2 Answers

How do you put the date on recording


Page 25 of user manual - see link below - explains how to super impose the date and time on the image

Apr 07, 2010 | Sony Handycam DCR-TRV265E Digital...

1 Answer

How is the time/date stamp displayed on a copy


The time/date is 'stamped' onto the video during recording. The time/date stamp function can be turned on or off in the setup menu. If it was 'on' during recording, it will be displayed when played back. If it was turned off, it will not be seen on the recording.

Jul 23, 2009 | Sony Handycam DCR-VX2100 Mini DV Digital...

1 Answer

How do you set the date & time


Somewhere there should be a menu button on the camera that will let you into a menu. if you find this, scrool through and there should be a date/time setting. Hope this Helps!

Feb 03, 2009 | Sony Handycam CCD-TRV318 Camcorder

1 Answer

Lost my manual


DatelTime Settings
1) Set the Power Switch 4D to "1M!" while pressing
down the Lock Button (I) located on the switch.
2) Press the MENU Wheel 0 in. The Menu Screen
appears.
3) Rotate the MENU Wheel 0 to select
"~TO SYSTEM MENU" and press it to display SYSTEM MENU. Rotate the MENU Wheel 0 to select "~NEXT" and press it to display the next page.
4) Rotate the MENU Wheel 0 to select "DATE/ TIME" and press it. The DATEITIME Menu appears.
5) To set "YEAR", "MONTH", "DAY" or "TIME" (hour/minute), rotate the MENU Wheel 0 to select the desired item, and press it. When the setting begins blinking, rotate the MENU Wheel o until the correct setting appears and then press it. The setting stops blinking.
6) When none of these settings ("YEAR", "MONTH", "DAY", "TIME") blinks, rotate the MENU Wheel 0 to select "~EXIT", and press it. The Menu Screen reappears with the highlight bar on "~RETURN".
7) Press the MENU Wheel 0 in to close the Menu
Screen.
. To display the date and time in the camcorder's display and on a connected TV, see DATEITIME
DISP. (U pg. 21) in SYSTEM MENU.
. The date/time cannot be stored in memory if the built-in clock battery runs out. Consult an authorized JVC dealer for replacement, or set the date/time as necessary before you start shooting.

Dec 17, 2008 | JVC GR-SXM260U Camcorder

1 Answer

CCD-TRV228E Hi8 - how do I remove LCD date or time


You can't remove date and time stamp on recorded movie now. Go to Menu and disable date-time stamp function for future recording.
User manaul of CCD-TRV228E is availabe here...
http://support.sony-europe.com/dime/camcorders/v8c/v8c.aspx?site=&m=CCD-TRV228E&site=odw_en_GB&odw_model=CCD-TRV228E
Have nice day.

Aug 06, 2008 | Sony Handycam CCD-TRV107E Camcorder

1 Answer

Sony Handycam DCR-TRV18E


Hi there,

Firstly you need the remote control that came with your camera (RMT-814).

Switch on your camera to VCR mode. Then on the remote, press the Data Code button (and of course, point the remote towards your camera). This should display the date and time in the bottom left of the screen.

It should display the appropriate date and time for each bit of recorded video.

Hope this helps!


Ron.

Jul 06, 2008 | Sony Handycam DCR-TRV18E Mini DV Digital...

1 Answer

Turning off recordng message.


You can turn the display off during playback mode, however, if the display was on during recording, that cannot be turned off. . 1. Press the DISPLAY button on the left side panel. 2. Each press of the button toggles the OSD function on and off. When you turn the OSD off : * In CAM mode: The STBY, REC, EASY.Q modes are always displayed on the OSD, even when the OSD is turned OFF and the key input is displayed for 3 seconds then turned off. * In PLAYER mode: When you press any Function button, the function is displayed on the OSD for 3 seconds before it turns off. Turning the DATE/TIME on/off * The DATE/TIME is not affected when the OSD function is switched ON or OFF. * To turn the DATE/TIME on or off, access the menu and change the DATE/TIME mode.

Sep 06, 2005 | Samsung DouCam VP-D5000i Mini DV Digital...

Not finding what you are looking for?

Open Questions:

See all Sony Handycam CCD-TRV87 Camcorder Questions

Sony Handycam CCD-TRV87 Camcorder Logo

Related Topics:

88 people viewed this question

Ask a Question

Usually answered in minutes!

Top Sony Video Cameras Experts

Larry Stiles
Larry Stiles

Level 2 Expert

286 Answers

kakima

Level 3 Expert

96683 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Are you a Sony Video Camera Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...