Question about Dual Electronics CECT P168 Cellular Phone

1 Answer

My i9 is always in emergency mode

I have at&t service and everytime i lose service it goes in to emergency mmode and the stay there until i take my sim card out and put it back in what do i do???

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 44 Answers

The i9 is a knock off iphone which is produced over seas.

They are poorly constructed but do "as some ads say" pack in the features for cheap.

Well the i9 online says is quad band which supports
850 / 900 / 1800 / 1900MHz

Thats just the type of connection it conects too.

in rural areas your most likely on the 850MHz Band, and the early models of this device didnt support 850Mhz.

I used to have one and i lived in a rural area = No Service.

Just from my opinion, i dont think that its actually quad band. Remember it is a knock off and it is false advertising but the earlier models did not support 850MHz..

I really doubt they do now.

Depending on what service your using, ATT, T-Mobile... Etc Etc.. you can go to there website and look at the coverage map and see what Band you lie under.

if you are in 850MHz than we could be on to something about false advertising :p but if your above that, lets say 900Mhz.. than most likely its a problem with the phone. and i wouldnt be shocked as it is a knock off.

and as for it being stuck in emergency mode, just doesnt have signal and when you take out you sim and restart it will try to connect and will till it looses signal and go sit back in emergency mode until you restart again..

could be signal, could be the phone.
i would search your coverage map and let me know.

Posted on Feb 17, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My razor maxx is stuck in emergency call screen. how do i fix it


Either the phone is broken (not likely), or the sim card is bad (more likely). Stuck on ''emergency calls only'' can also happen due to running out of minutes on your plan. And/or failure to pay the bill and losing service because of that. // Basically, whenever a phone does not have a service provider (for whatever reason), by law it must be able to dial emergency 911. So, if you are out of minutes and/or don't have a phone plan, your phone would do exactly what it is doing. Same thing if the Sim card is bad. The phone doesn't detect a ''service provider'' and so it goes into ''emergency mode.'' Ask your service provider to check your sim card for you.

Jan 01, 2015 | Cell Phones

1 Answer

My Razr v3xx keeps losing service and it keeps going in to like emergency call mode to


If it shows Emergency Mode means it locked To Network ,you need to Unlock it,get the Unlock code at here
http://www.mobile-unlocker.com/supported-phones/rs2wp7/ and Unlock it..

Apr 22, 2011 | Cell Phones

1 Answer

I turn on my phone it goes to a screen saying Emergency Download


Wait does it say emergency mode only? If so this has happened to me many times on this phone.

Turn off the phone and remove the battery. In there will be you should see the SIM card. Pull out the SIM and put it back in. Put back the battery and turn on your phone.

For some reason on these phones the SIM card gets dislodged. When it does the phone won't work because the SIM card is what makes the phone your number etc. All cell phones, that have no service otherwise will be able to call 911. Apparently it is a law, so that is why your phone is on emergency mode. Without the SIM card the phone is a phone without service and will therefore only work in emergency mode.

I hope this is what you meant.

Aug 13, 2009 | LG Vu CU920 Cellular Phone

1 Answer

Bad signal i9 3g


maybe your phone signal probleam so better u add your phone signal boost up strip u can buy it and if u put it inside your mobile signal will be ok
good luck

Jul 14, 2009 | Dual Electronics CECT P168 Cellular Phone

1 Answer

CECT I9 does not let me make calls!


the band is 850 (you can switch this manual or let it switch automatically)...on cell go to call center / call settings and switch end call to off....

Jun 21, 2009 | Dual Electronics CECT P168 Cellular Phone

1 Answer

Can't receive/make calls and text on i68/i9


First remark: This phone is not 3G compatible !!! the name is i9+ 3G but it's only the name !!! Second: Go to settings , Dual SIM settings , and check that you're not in 'flight mode' (that's when the 2 X appear top left) and change it to either one of the 3 other options (Dual sim open, only sim1 open, only sim2 open). Third: The name will appear when the person is in your address book.

Feb 22, 2009 | Dual Electronics CECT P168 Cellular Phone

1 Answer

How to verify sms/mms


  1. Press the Menu Key.
  2. Scroll to and select WebAccess.
  3. Scroll to and select Web Sessions.
  4. Scroll to "mMode", then press the Menu Key.
  5. Scroll to and select Edit.
  6. Validate the following:

    Note,Settings for multi media service will stop if the port 1 is blank
  • Name: mMode
  • Homepage: http://home
  • Service Type 1: WAP
  • Gateway IP:10.250.250.250
  • Port 1: 9201
  • Domain 1: Blank
  • Gateway IP 2: 000.000.000.000
  • Port 2: 8080
  • Domain2: blank
  • Service Type 2: WAP
  • DNS 1: 000.000.000.000
  • DNS 2: 000.000.000.000
  • Timeout: 5 minutes.
  • CSD no 1: Blank
  • Username: Blank
  • Password: Blank
  • Speed (Bps) 1: 9600
  • Linetype 1: ISDN
  • CSD 2: Blank
  • Username 2: Blank
  • Password 2: Blank
  • Speed (Bps): 9600
  • Line Type 2: ISDN
  • GPRS APN: Enter the your Apn
  • Username: Enter your user name
  • Password: Enter your password
  1. Click Done.
Once the browser settings are configured, please select it as the active web session:
  1. Press the Menu Key.

  2. Scroll to and select WebAccess.

  3. Scroll to and select Web Sessions.

  4. Scroll to "mMode", then press the Menu Key.

  5. Select Set Default.

NOTE: APN: Access Point Name.

Please rate this a fixya

Feb 13, 2009 | Motorola Mobility RAZR V3

1 Answer

Personalization screen


BDEATH HERE. First turn on your motorola by pressing *# and red key at the same time to get in the boot loader mode. Then try download flashbackup 6.22 version for motorola. Visit motox site to find the best flash monster pack for your motorola. Also write down your s/w version, flex version and what boot loader your cell phone has. and get the usb cable. Up then tell me what happened!!

Sep 03, 2007 | Motorola Mobility V220

Not finding what you are looking for?
Dual Electronics CECT P168 Cellular Phone Logo

438 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dual Cell Phones Experts

William Alequin

Level 3 Expert

853 Answers

Michael Terence...
Michael Terence...

Level 2 Expert

102 Answers

venugopal durairajan

Level 3 Expert

464 Answers

Are you a Dual Cell Phone Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...