Question about Zanussi TLE1116W Top Load Washer

Open Question

Zanussi TLE 1116W starts filling then jumps to drain

It was fine until yesterday but today it is filling for 30-60 seconds then jumps to drainin, empties water and ends the program.
Any help is appreciated.

Posted by on

5 Suggested Answers

  • 1462 Answers

SOURCE: Reluctant to start

problem is almost certainly the door interlock. to replace, remove the plastic clip holding the door boot onto the cabinet and peel it back adjacent to the door lock. the door lock is just held in by two screws accessible at the front of the cabinet. not an expensive part. easy job - takes about 10 min

Posted on Mar 26, 2007

  • 1462 Answers

SOURCE: the Washing Machine fills and then empties with not running a wash cycle

possible a pressure stat fault. some pressure stats have a too high water detector which turns on pump

Posted on Mar 27, 2007

  • 1 Answer

SOURCE: Zanussi zwf1631w jetwash front loading washing m/c

had to call an enginer out, the problem was down to a faulty motor rota, to identify if e30 is this fault, rotate the drum (so the motor rotates) and try to start the m/c. if it runs ok you know to change the rota. hope this may help someone

Posted on Sep 16, 2008

gittos73
  • 244 Answers

SOURCE: zanussi Turbodry 1200 spin problem

if this washer is used alot then it will more then likely be the carbon brushes which u will need to take the lid off undue 4screws out where it joins front to the back screws at the back to the bottom and 1screw either side of the bottom where the panels join together behind a little cap which will have an hole in the middle of it to get it out u will then be able to get to the motor to replace the carbon brushes

Posted on Nov 25, 2008

  • 17 Answers

SOURCE: our washing machine (Zanussi ZWF 1632 W) flashes 5 times

This is a motor problem the end light flashing 5 times indicates error E50. The motor has either got wet or has just failed i would suggest trying to dry it 1st but i would suspect the motor has gone down to earth usually having to replace it. The part no. DST1246179079 Motor aprox £195 but shop around you may find it cheeper.

Posted on Dec 17, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Battery fully charged but needs jump to start


Check cables,. SOund like you have a wire shortage, Somethng is drainin down battery. Have battery checked.

Jul 09, 2013 | Dodge Neon Cars & Trucks

1 Answer

Lid is not locking properly, washer sensor is overfilling, and the washer wont spin


Check door switch: If the lid switch is bad it will not drain or spin. Try this test: With lid open let it finish wash cycle. Press lid switch down with screwdriver. Washer should begin draining. Release switch. Motor should stop. Press switch a second time. Washer should start spinning as it continues to drain. If motor doesn't come on while lid switch is pressed, replace the switch. OR
http://www.youtube.com/watch?v=q942xn_2VXY
Pl click if helped.

Apr 28, 2013 | Whirlpool WTW4950XW Washer

1 Answer

My kenmore washer model#110.24422300 is not agitating, spinning or draining. Problem started today, it work fine yesterday. Tried selecting different settings to get to agitate or drain, did not work.


Hello & Welcome to FixYa

When the washer fills but does not agitate or spin then you can check if the lid switch is fine. You can jump start the lid switch by connecting both the wires with each other or use the third wire to act as jumper between the two. After this if the problem is solved then replacing lid switch is recommended repair. Please get back to me if you have any other questions.

Kevin

Aug 07, 2011 | Kenmore 22422 Top Load Washer

1 Answer

It does not drain water


check the drain hose remove for drain and drainin to a bucket... if it work you have a plugged drain... hope it helps

Sep 19, 2009 | Frigidaire Dishwashers

1 Answer

Drainin coolent


pull the pipe off, take and unhook the tube going to the water pump let it drain. but if you want to drain it out of the motor then you will have to do some tearing apart. to refill it take off radiator cap fill it start it with the cap OFF for a few seconds (this works the air out of the system) then turn bike off and top it up.

Apr 17, 2009 | 2004 kawasaki KDX 200

2 Answers

E85 fuel in a regular gas tank


drain the tank change the fuel filter motor will be fine
it'll run funky until the e85 is flushed out

Dec 12, 2008 | 2001 Ford Windstar

Not finding what you are looking for?
Zanussi TLE1116W Top Load Washer Logo

Related Topics:

37 people viewed this question

Ask a Question

Usually answered in minutes!

Top Zanussi Washing Machines Experts

Gerry Harvey
Gerry Harvey

Level 3 Expert

1456 Answers

shaun taylor

Level 3 Expert

1450 Answers

Chris Hall
Chris Hall

Level 3 Expert

842 Answers

Are you a Zanussi Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...