Question about GE Ovens

1 Answer

F2 code on GE selfcleaning oven

Half way through cycle F2 code comes on an beeps

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

  • Expert
  • 117 Answers

The F2 fault code generally means the Oven temp exceeds 590 w/ unlocked door High resistance or interference in oven temperature sensor Might want to check the oven sensor for high resistance. Get a ohm reading of the oven sensor at room temperature and tell me what this reading is.

Waiting to hear from you,
Eric Campion

Posted on Feb 14, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What does the code f2 and f3 mean?


my ove is in selfcleaning mode and is beeping f2

Feb 16, 2012 | Kenmore 47712 / 47714 / 47719 Electric...

2 Answers

Tried to do self cleaning on oven, about 10 minutes in got "f2 locked door" and it won't clean. what is that all about?


Error code F2 on clean cycle is indicating that the maximum permissable cleaning temperature has been exceeded. (or it's got too hot!)

However it seems unlikely that that would happen in just 10 mins. more likely it is a problem with the oven temperature sensor which should be checked over as should the lock switches..

Dec 14, 2010 | GE JRP24 Electric Double Oven

1 Answer

F2 Failure Code after cleaning cycle on GE Double


f-2 is usually a runaway oven temp which most of the time means a bad oven sensor.try replacing this first.

Jan 16, 2010 | GE Ovens

1 Answer

F2 code


Hi, this will occur if the oven control senses the oven temperature above 915F-930F



If actual over temperature condition occurred: Look for welded relay contacts. If this happens, replace oven control (also called clock or ERC).

If no over temperature condition occurred: Look for a high resistance connection or any other cause of high resistance in the oven temperature sensor circuit. Check sensor, sensor harness and sensor harness connection at sensor and oven control. Replace sensor if found defective. Check door lock switches.

Remember: Oven control (ERC) measures resistance of sensor circuit , not actual oven temperature.

Jul 19, 2009 | GE Profile JTP18 Electric Single Oven

1 Answer

F2 error


F2 is a bad temp sensor, needs to be replaced.

Jun 23, 2009 | GE JKS06BFBB Electric Single Oven

1 Answer

Error code F2 keeps beeping! Will not reset. Any


thats the oven sensor , replace the sensor and your good to go

Jun 17, 2009 | GE JKP27 Electric Double Oven

1 Answer

Dacor single oven flashes an F2 error code and won't stop beeping!!!


This is from manufacture service manual:

-F2- Alarm Heating Mode High Temperature
Is activated when the ERC senses a runaway heat condition or when the temperature exceeds
“runaway limits”. The ERC will beep until the cancel or another function is selected. If the alarm
repeats the F2 alarm check the oven sensor and wiring after fi rst checking for a stuck relay. If alarm
goes away verify the oven will complete a clean cycle without any type of failure.
Another words the problem with oven sensor or relay board.

Oct 26, 2008 | Dacor MCS130 Millennia Electric Single...

1 Answer

Oven


I used the self cleaning mode for 2 hours and the error f2 keeps flashing and beeping, I did try to power off with the breaker and left it off for about a half hour and it still continues to beep and flash f2, what should I do?

Aug 07, 2008 | Ovens

2 Answers

F2 error


what is solution

Dec 08, 2007 | Ovens

2 Answers

F2 error code


Similar problem. When baking over 400 degrees we get the F2 code that can only be reset by cycling the power at the breaker. Replaced the electonics to no avail. I'm thinking its the cooling fan located between the oven and microwave (upper unit) it never comes on which may cause a separate temp switch to generate the F2... but I'm not a pro. :)

Nov 18, 2006 | GE JGRP17 Gas Single Oven

Not finding what you are looking for?
Ovens Logo

Related Topics:

717 people viewed this question

Ask a Question

Usually answered in minutes!

Top GE Ovens Experts

William Miller
William Miller

Level 3 Expert

8820 Answers

Michael Thomas
Michael Thomas

Level 3 Expert

3051 Answers

Dan Webster
Dan Webster

Level 3 Expert

8147 Answers

Are you a GE Oven Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...