Question about Fujitsu 18C1 Air Conditioner

1 Answer

CODE FLASH 2TIME

ASTA09LCC FAULTY CODES

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Fujitsu clear the code

Posted on Feb 14, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What does 3 green led flashes in sequence, operation led off mean on Fujitsu ASTA09LCC aircond


This means a "Serial reverse transfer error during the operation"
Diagnosis:
When the indoor unit does not receive the signal for 10 consecutive seconds during the operation
>Permanent stop after 30seconds.
[Diagnosis Point]
Check the indoor /outdoor cable connection (in order). If the cable wiring is not abnormal, measure the voltage of the outdoor
unit terminals and diagnose the defective location.
(Refer to the after mentioned [Serial Signal Diagnosis] for the voltage measuring method and diagnosis method.)

This is generally caused by a faulty controller board in the outdoor unit. Often they are shorted out by geckos or bugs but sometimes a power surge.

Jul 14, 2015 | Fujitsu Air Conditioners

1 Answer

My kelvinator split sys turns on for about 5 min the 4 lights flash blows warm air have no manual


If the 4 lights are the indoor unit indicator lights, it is a fault code. Do some lights stay on or do all flash? What model is it? Kelvinator ( In Australia) are sourced from various OEM suppliers, different models will have different fault codes.

Mar 16, 2015 | Air Conditioners

1 Answer

PANASONIC DMR BS850 SHOWING ERROR CODE F5 202 CAN IT BE FIXED


hi,
Fault Code At Remote = F5
Indoor Unit PCB
LED1 = Lit
LED2 = Lit
LED3 = Lit
LED4 = Lit
Outdoor Unit PCB
LED1 = Lit
LED2 =
LED3 =
LED4 =
Measuring Of Fault Code = Signal from RC to ID faulty.

Air Conditioning Fault Codes

Feb 28, 2014 | Air Conditioners

2 Answers

Error code e4 unit airconditioner


Not sure about E4 , but 4 blinks or flashes usually means the compressor isn't starting properly. It could be a faulty start capacitor or wiring or faulty indoor PCB (Board)

Oct 18, 2013 | Mitsubishi Mr. Slim MXZ30TN Air...

1 Answer

Timer light flashes twice on my asta09lcc but it wont work


If operation light is normal and timer light flashes twice, the error is:
Serial signal (reverse) error, at operation start up
Most likely a faulty outdoor controller PCB. Around $250 for new board plus labour.

Jul 09, 2012 | Fujitsu 18C1 Air Conditioner

1 Answer

Fujitsu Inverter ASTA09LCC Where is the drain tube located? The air con is leaking water and I believe drain may be blocked.


It is directly behind & thru the wall to outside next to the refer. piping.Everything goes outside thru a 3" hole. tube should b there.Blow it out.good luck

Mar 12, 2010 | Fujitsu 18C1 Air Conditioner

2 Answers

Remote doesn't work on air con


Should be current detect pcb faulty, or compressor drawing too much current.
I don't have your model a/c, but panasonic fault codes stay pretty much the same
Normally panasonics have this info on the inside of the access panel.
Plus fault codes from the indoor unit make it easier to look up.

if the compressor is running, check the amps and refrig pressures.

Sep 19, 2009 | Air Conditioners

3 Answers

Fujitsu Inverter ASTA09LCC - heating not working


Use a pen to hit the reset button on the remote. 

Feb 09, 2008 | Fujitsu 18C1 Air Conditioner

Not finding what you are looking for?
Fujitsu 18C1 Air Conditioner Logo

Related Topics:

380 people viewed this question

Ask a Question

Usually answered in minutes!

Top Fujitsu Air Conditioners Experts

yadayada
yadayada

Level 3 Expert

61168 Answers

BOB  BROWER
BOB BROWER

Level 3 Expert

267 Answers

Bill Long

Level 3 Expert

577 Answers

Are you a Fujitsu Air Conditioner Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...