Question about Hobart 41 in. AM14-255 Free-standing Dishwasher

1 Answer

Reset swish my hobart doesn't go up to temp on the rinse cycle.I have to push the reset swish every time!

Posted by on

  • yvanmac1 Feb 14, 2009

    the red button that keep on reseting.yes

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 640 Answers

What reset switch?The red button on the booster (it sits underneath to the left)?

Posted on Feb 14, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My Hobart runs continues cycles and will only stop when I open the door...what is causing it to not stop after the rinse cycle?


When I did commerical Hobart repair, this usually was a timer issue..on this model is it a digital timer or a manual dial timer that you turn to select cycles? Another thing is..some dishwashers water temp has to be a certian temp before timer will advance.

Jan 07, 2015 | Hobart Dishwashers

1 Answer

I have a am-14 hobart washer. having problem with rinse temp indicator. it is fine for the wash then the temp gauge is jumping around, could it be the thermostat?


Your rinse temperature sensor that is a tiny probe in the water piping (top rear of machine) needs replaced. Hobart part # 00-294692. It costs about $84.

Oct 19, 2012 | Hobart Dishwasher Am-14 Commercial Dish...

1 Answer

My sr24h hobart undercounter dishwasher is stuck in a mode where all it does is drain water out. Will not do anything else...???


Hello There; If your unit stuck on the wash cycle and not advance to rinse cycle because the rinse water is not up to 180 degree . You've to check out the booster element and the rinse temp. I hope this will help.

Sep 19, 2010 | Hobart SR24-H Built-in Dishwasher

1 Answer

Hobart WM-ID dishwasher doesn't heat water enough to clean dishes


The WM-1D does not have any internal heating devices. You have to supply the machine with the proper water temp. It has two fill valves, one for wash and one for rinse. It should have 150F supplied to the wash fill valve and 180F to the rinse fill valve.

Feb 04, 2010 | Hobart AM14C-155 Dishwasher

3 Answers

After pressing On - the dishwasher just sits are about 80 degrees and doesn't get any hotter when normally it goes up to about 118. Can we still use it to wash or is something wrong?


A hobart LXIH-3 uses a chemical to sanitize however a 120 degree wash temp is required as well.

Turn up your hot water tank that supplies the dishmachine, make sure your sanitizer is pumping into the rinse cycle using micro-clorine test papers and all is well.

Dec 22, 2009 | Hobart 24 in. LXIH-3 Built-in Dishwasher

1 Answer

Temp. too hot


First off, the temp adjustment can only be made by a trained service tech, since the dishwasher will need to be reprogrammed to allow for a lower temperature in the rinse cycle but still have the higher temp needed in the wash cycle. Also, since any change in the water temp settings will require a longer wash and rinse cycle to be programmed into the unit.

Of course, you could simply lower the water temp on the water heater that supplies water to this unit, but you'd have lower temp water elsewhere and likely get cited at the next heatlh department inspection on that issue.

Since this is a commercial dishwasher, you might want to reconsider lowering the temp, since health codes and standards for commercial establishments require a MINIMUM water temperarture of 185 degrees F (85 degrees C) for proper operation and to get all the crud off the dishes, etc.

Note, the manufacturer sets these units to the higher temp, 203 degree F (95 degree C) knowing that the water will cool down quickly once the wash cycle starts and the water contacts the dishes, etc. That is also why these units have a added heater element, to help keep the water at the correct temperature needed to both clean AND sanitize the dishes, according to established health standards.

If you really want to change the water temp settings, contact your Hobart service rep and explain the reason you want it lower and see what they say.

Hope you found this very helpful and best regards!

Aug 19, 2009 | Hobart SR24-H Built-in Dishwasher

1 Answer

Tank temp


check to see if your element is scaled up or your element may be damaged

Nov 21, 2008 | Hobart AM15T Dishwasher

1 Answer

Rinse not hot enough


145 degree is just your hot water temp and that your dishwasher hot water booster is not working assuming that this machine has worked in the past to produce final rinse water above 180 degrees. Remove the bottom panel and to the right you will see the booster tank, look for a nickel size component with a small red button on it. Try pushing on it to reset it. If that does not work, check for voltage at your heating element on your booster tank. (the thicker wires) If voltage is present then your heating elements need replacing.

Nov 13, 2008 | Hobart 24 in. LXIH-3 Built-in Dishwasher

1 Answer

Hobart LXIH displays P2


The rinse thermistor is bad,look on the back of the machine to the right and you will see 2 black wires with a plug that screws into the vac breaker this is the probe.I bet when the dishwasher goes into the rinse cycle the temp jumps all over,let me know.

Jul 27, 2008 | Hobart 24 in. LXIH-3 Built-in Dishwasher

Not finding what you are looking for?
Hobart 41 in. AM14-255 Free-standing Dishwasher Logo

Related Topics:

308 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hobart Dishwashers Experts

Ricardo311

Level 1 Expert

36 Answers

yadayada
yadayada

Level 3 Expert

60792 Answers

handygirl911
handygirl911

Level 2 Expert

55 Answers

Are you a Hobart Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...