Question about Hotpoint Ariston WD440G Front Load All-in-One Washer / Dryer

1 Answer

Waste hose connection hotpoint wd440g

My wd440g is not draining properly. I have taken the lower back panel off but cannot detach the outlet hose from the machine as it is has a strange interlocking, white plastic, key type connection. How do I undo this?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 135 Answers

Have you checked the filter? This can be found at the large end of the pipe. It is secured with a large jubilee clip.
Thankyou for using Fixya.

Posted on Feb 13, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Heater core 1991 corsica needs to be replaced. how do i get to it?


1991 VEHICLES
  1. Disconnect the negative battery cable.
  2. Drain the cooling system into a suitable container.
  3. Properly disable the SIR system, as outlined earlier in this section.
  4. Remove the instrument panel as outlined in this section.
  5. Remove the screws and floor outlet, turning clockwise and to the right to release from the rear floor air outlet.
  6. Raise the vehicle and support it safely.
  7. Detach the heater hoses from the heater core.
  8. Disconnect the drain tube elbow from the heater core cover.
  9. Carefully lower the vehicle.
  10. Unfasten the retaining screws, then remove the heater core cover.
  11. Remove the core screws, clamps and heater core from the vehicle.
e9c0b51.jpg

Fig. : Exploded view of the heater core and related components - 1991-92 vehicles without A/C


To install:
  1. Reposition the heater core and install the straps and screws.
  2. Install the heater core cover and attaching screws.
  3. Install the floor outlet and retaining screws.
  4. Install the instrument panel.
  5. Raise the vehicle and support it safely.
  6. Connect the heater hoses to the heater core.
  7. Carefully lower the vehicle.
  8. Fill the cooling system with the proper type and amount of coolant.
  9. Enable the SIR system, as outlined earlier in this section.
  10. Connect the negative battery cable, then start the engine and check for coolant leaks. Check the coolant level, and add if necessary.

Hope this help (remember rated this post). Good luck.

May 15, 2010 | 1991 Chevrolet Corsica

1 Answer

How does the wf430 hotpoint washing machine drain


Normal 0 false false false MicrosoftInternetExplorer4 /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-parent:""; mso-padding-alt:0cm 5.4pt 0cm 5.4pt; mso-para-margin:0cm; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:10.0pt; font-family:"Times New Roman"; mso-ansi-language:#0400; mso-fareast-language:#0400; mso-bidi-language:#0400;} Not too sure what you mean but will try to explain. The water in the tub is only kept there because one end of the outlet hose is higher than the tub and the job of the pump is to push the water up the hose and out. If the outlet hose is lower than the tub, all the water inside will just flow out, the pump does not hold the water in the machine it only assists in its removal. If you remove the pump from the machine altogether then the water will just flow onto the floor but if you disconnect the pump from the wiring circuit it will just mean you have no mechanical way of emptying the tub. However if you lower the hose to the ground then by the force of gravity the water will flow out. Just one other point, the hose should come out of the machine and rise up the back of the cabinet then loop down again where it fits into a stand pipe or is connected to a waste pipe, if however the end of the hose is lower than the tub you will get a siphoning effect happen after the first pump out in which case the water from the machine will just empty on its own without the aid of the pump. For more Hotpoint aid visit Selfix-uk

Mar 11, 2010 | Hotpoint WF430 Front Load Washer

1 Answer

Wheres the filter on the hotpoint wd440


Remove front kick plate at bottom of the machine and see if there is a filter behind it. If not you need to remove lower back panel from machine, then remove sump hose, (Large black hose situated under tub) To remove this you may need grips for removing the retaining clamp.Although on some machines it may be a large jubile clip

Feb 17, 2010 | Hotpoint Ariston WD440G Front Load...

1 Answer

How to replace a heater core


Removal & Installation
CAUTION When draining the coolant, keep in mind that cats and dogs are attracted by ethylene glycol antifreeze, and are quite likely to drink any that is left in an uncovered container or in puddles on the ground. This will prove fatal in sufficient quantity. Always drain the coolant into a sealable container. Coolant should be reused unless it is contaminated or several years old.

  1. Disconnect the negative battery cable and drain the cooling system.
  2. Raise and support the vehicle safely.
  3. If equipped, remove the rear lateral transaxle strut mount.
  4. Disconnect the drain tube from the heater case.
  5. Detach the heater hoses from the heater core.
  6. Carefully lower the vehicle.
  7. Remove the right and left sound insulators.
  8. Unfasten the steering column opening filler. Disconnect the heater outlet deflector (floor air outlet duct).
17a0e5f.gif
Disconnect the floor air outlet duct

Remove the heater core cover.

f5c7d32.gif
Unfasten the retaining bolts, then remove the heater core cover

Detach the heater core retaining straps (clamps), then remove the heater core.

cf9e872.gif
Detach the retaining clamps or straps, then remove the heater core


To install:
  1. Install the heater core and retaining straps (clamps).
  2. Install the heater core cover.
  3. Reconnect the heater outlet deflector (floor air outlet duct).
  4. Install the right and left sound insulators. Install the steering column opening filler.
  5. Raise and support the vehicle safely.
  6. Connect the heater hoses (use new heater hose clamps if necessary) to the heater core.
  7. Connect the drain tube to heater case.
  8. Connect the rear lateral transaxle strut mount, if equipped.
  9. Lower the vehicle.
  10. Fill the cooling system and check for leaks. Check heater system for proper operation.

Nov 13, 2009 | 1994 Chevrolet Cavalier

1 Answer

HOTPOINT WASHER DRYER WD440G


That means that the machine detected a problem at a certain point of the cycle and stopped.

If the machine stops when filling check the inlet valve and the water supply.

If it stops because ofervilling check the water level switch.

If it stops when the cycle is hot water only , then check the heating element.

If it stops when draining, then inspect drain filter, drain pump , and drain hose. You access the drain hose removing a panel at the front side of the machine.

If it stops when motor is supposed to spin faster (rinse) then it is motor control unit or motor coupler.

If it is none of the above, then it is a defective control board.


Feb 16, 2009 | Hotpoint Ariston WD440G Front Load...

1 Answer

Hotpoint WD440G In wash cycle and blows all household plugs


syphon out the water by getting the end of the drain hose into a basin and putting it lower than the water level. a few shakes usually gets it flowing. you probably have a short circuit. my guess would be the heater box/element to start.

Jan 30, 2009 | Hotpoint Ariston WD440G Front Load...

1 Answer

Wd440g Hotpoint - in wash cycle and is blowing all the household


you will have a short circuit somewhere. usually the dryer box, but to get the water out you need to put the end of the drain hose lower than the water level into a basin to syphon it out.
the heating element of the dryer sometimes come loose on these machines and can be the cause of a short.

Jan 30, 2009 | Hotpoint Ariston WD440G Front Load...

1 Answer

Hotpoint aquarius WMA58 spinning but not draining away all the water


Suggest you check pump filter.
you will find it located at the rear right side of the m/c.
Remove lower rear panel, there you will see a large black hose, remove securing clip, and detach hose, the filter is located inside, remove and clean, make sure you put everything back in the same order you took it off.
This should solve your prob. Make sure the drain hose is not clogged and the outlet is clear also.
Plz rate my solution.
Thanks.

Dec 21, 2008 | Washing Machines

2 Answers

Hotpoint ultima wma75


sounds like the filter is blocked you can take the filter out and clean it and check the hole for lint a sock or a coin etc. if this helps please rate me joe

Aug 06, 2008 | Hotpoint First Edition WMA12 Front Load...

1 Answer

Hotpoint dishwasher


Did you have a dishwasher before? If so, you must have had a sink tail piece with a dishwasher drain coming off the side. For the connection, you may have to get an adapter to fit the end of the dishwasher drain hose to the sink tail piece. Take all pieces to hardware store if necessary to get an adapter which fits. After you connect the drain hose, make sure that the drain hose has a "high loop", meaning that the hose curls up at least 6 inches above the connection point before it goes down again. This is important to keep sink waste from getting back into the diswasher hose if the sink drain backs up.

Feb 14, 2008 | Dishwashers

Not finding what you are looking for?
Hotpoint Ariston WD440G Front Load All-in-One Washer / Dryer Logo

138 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hotpoint Washing Machines Experts

hungoverrr

Level 1 Expert

5 Answers

puggy666

Level 1 Expert

47 Answers

freddyfox

Level 2 Expert

236 Answers

Are you a Hotpoint Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...