Question about Dremel Variable - Speed Multipro Rotary Tool 395

1 Answer



Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Master
  • 10,865 Answers

This homelite saw requires homelite chain oil as there is no adjustment.

Posted on Feb 26, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

How to fix the choke on homlite 38 cc 16 inch gas chain saw

More than likely, your choke became disconnected. I have attached a link from YouTube of a video on this.
There are many useful video's on fixing chainsaws, from simple fixes such as reattaching a choke lever, to complete tear down and rebuilds.
I hope this helps you get back up and running.
Short video on fixing chain saw choke

Nov 10, 2014 | Garden

1 Answer

Yesterday around five i was chopping some logs out of a small tree i felled. i was doing a under cut to the top tru a small bout three inch tree. next thing i know my blade isnt spinning. so i stoped for...

I don't have any poulan saws mine are all stihl and homelite but they all have a chain lock on them .It is located on the front of the motor on top of the saw and if they are hit fairly hard they will lock down on the chain to prevent injury. Try to push the bar forward then pull it back towards the rear of the saw. You should hear it click when it resets.Hope this helps you. Thank you

Jan 06, 2011 | Poulan P3314 14" Gas Chain Saw 2.0 Cuin...

1 Answer

What is the mix for my Homelite 16" 33cc chainsaw?

50:1 is the fuel to oil ratio. Never use petroleum oil (engine or boat motor oil). Always use a synthetic saw oil available from home centers, hardware stores and saw dealers. The bottles are usually graduated to various ratios for a gallon of fresh gas. Always premix in it's own container and shake the container thoroughly each time just before filling the tank to prevent oil starvation. Be sure to use bar/chain oil for the chain as well, and keep the chain sharp and well adjusted. Hope this helps!

Nov 14, 2010 | Poulan Pro 14" Gas Chainsaw 33CC P3314

2 Answers

I have a poulan 14 inch woodshark chainsaw and it ran fine when i got it but now i have to keep gunning the gas to keep it running and i have cleaned the air filter and cleaned the carb.

Turn up your low speed jet about 1/4 turn. You have 2 holes in the side, one says slow or low and the other says high,, or fast, turn the slow jet in 1/4 or out if that doesn't work, then try it, you will find the right spot. Hope this helps.

Mar 13, 2010 | Poulan P3314 14" Gas Chain Saw 2.0 Cuin...

2 Answers

Ryobi 540A need manual runs slow/ chain too tight?

Actually, I own one of these battery operated Ryobi chain saws too. It is normal for the saw to run slow. Remember it is battery powered, not gas, so its not going to be a high rpm saw. Be patient whit it, and you'll get about 4-6 cuts per battery. I take mine camping. It sure is nice not having to listen to a two-stroke while relaxing in the woods! Dont plan on cutting lots of stuff, either, or you'll burn up the motor. This thing works great for very mild workloads.

Aug 14, 2009 | Ryobi Factory Reconditioned 10-Inch 18...

1 Answer

Have a 455 rancher saw that is spitting chain oil out, is there a way to regulate how much oil is automatically dispersed to chain?

If it is spitting oil out, then your chainsaw is working properly. When it stops spitting oil out, then you have a problem. However, on the bottom of that particular saw you will find a little hole with a picture of an oil can next to it. You can adjust the lubricant output via the screw located at the bottom of that hole but, keep one thing in mind; the harder the wood or working conditions your saw is being exposed to the more oil will be necesary to keep your saw running smoothly and your chain from prematurely dulling.

Aug 09, 2009 | Husqvarna , No.455 Rancher, 20" Gas -...

1 Answer

Need chain saw fix

I would try and look at their user manuals for the adjustment. They are different on most saws. Hope this helps

Mar 11, 2009 | Poulan P3314 14" Gas Chain Saw 2.0 Cuin...

3 Answers

Need to adjust carburetor jets of homelite chain saw

what is the adjustment for high and low settings on a homlite 330 ?

Jan 11, 2009 | Garden

Not finding what you are looking for?
Dremel Variable - Speed Multipro Rotary Tool 395 Logo

Related Topics:

278 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dremel Tools & Hardware - Others Experts

Doctor PC
Doctor PC

Level 3 Expert

7733 Answers


Level 3 Expert

4345 Answers


Level 1 Expert

6 Answers

Are you a Dremel Tool and Hardware - Other Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides