Question about LG 50PX2DC 50 in. Plasma Television

1 Answer

Remote will no longer control the tv

Powers on and off at tv, but remote no longer controls it.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Make sure the "TV" button is selected on the remote

Posted on Feb 11, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Remote control issues


If you whsh to get all functions operated with your TV, you must have its original remote control, and it is no doubt. No universal remote control will operate with all functions, that are supposed to be, especially to Sony Brands. You can buy the original remote control from the authorized service center for Sony, or from any authorized dealer for Sony. Then why do you go for an experiment

May 14, 2013 | Sony Bravia KDL-32V4000 32 in. LCD TV

1 Answer

"I have LG 37LC2D TV,when I turn the power on remote controlled or manually it immediately powers off. Is this an issue with the on/off switch inside the tv and how can remedy the problem?"


I have an LG as well.
My troublshooing says:
"Check the power control setting.The power supply may be interupted.
Check if the Auto sleep feature is actiated in the Time settings.
Refer to the " Sleep timer".
If there is no signal while the TV is on, the TV will turn off automatically after 15 miutes or so"

Feb 24, 2012 | LG 37LC2D Television

1 Answer

Vizio TV remote is in conflict with Shaw TV remote. When the TV is on, the Shaw bow and the shaw remote control would not work. I turn both systems off, then turn the box on with the remote, select a...


You need to "program" your Shaw remote to control your TV, including the volume up/down on the remote.
Take your Shaw remote control, and follow the instructions on the back. If that does not work, telephone Shaw, and ask for technical support for TV.

Mar 09, 2011 | Vizio M420VT 42 in. LCD HDTV

1 Answer

Can set up th remote control for this tv with the direct tv cable remote


Here's how to scan for TV codes on your DIRECTV remote

1.Make sure your TV is turned on.

2.Slide the mode switch at top of remote to "TV".

3.Press and hold the MUTE button. This is located above the number 1 button.

4.While still holding down MUTE, press and hold the SELECT button until green light at the top of the remote flashes twice.

5.Then enter 991, the green light on remote should flash twice.

5b. Press 1 again (it will flash twice again), then you press the power on button at the very top right.

6.Point remote at TV and press CHANNEL UP button. Tap the CHANNEL UP button repeatedly until the TV powers off.

*If you hit channel up very fast, you risk going past the code. Pressing channel down will back it up. I alway hit channel up very fast till the tv turns off, then back it up slowly till it comes back on.

7.When the TV powers off, press and release the SELECT button.

*Note: If the green light flashes three times before TV responds, then all codes have been cycled through. Our remote controls are guaranteed to program to your DIRECTV receiver, however your TV may not be compatible with our remote control.

Mar 05, 2011 | Curtis LCD2425A TV

1 Answer

I need the universal codes for my verizon fios remote, otherwise another recommendation of a universal remote that will operate my tv.


Setting up the Philips RC 144 remote if the remote codes are invalid or unknown If you do not know the remote codes for a device, or if you've tried all the listed remote codes for your device and none of them work, you can search for the correct remote code by following the steps below.

Note: These steps only apply to the Philips RC 144 Remote Control. If this is not the make and model of your remote, go to the supported remote control models page and find the instructions for your specific remote control.

Searching for a Device Code
  1. Turn on the device you want to program into your remote, for example if you are programming your remote to control your TV, then turn on the TV.


  2. Press and hold the device button for the device you turned on in step 1 (DVD, AUX, TV, STB) and press OK. Release both buttons.

    The mode buttons blink twice.


  3. Press 922.


  4. Point the remote control toward the device you are setting up and press the upper part of the Play button.


  5. Press the Fast Forward button. If the device you are setting up does not turn off, keep pressing the Fast Forward button until the device powers off. (You can use the Rewind button to go back, if necessary.)


  6. When the device powers off then you've found the correct code for that device. Press OK to assign the code in your remote control.


  7. Note:
    There are over 200 possible combinations for TV and DVD codes. The most common codes are tried first but you may still need to press the Fast Forward or Rewind buttons over 200 times to find the correct code for your device.

    If you reach the end of the list of codes, the entire remote flashes twice and returns to normal operation. You can exit programming at any time by pressing the Exit button.

Feb 28, 2011 | Apex Digital LD4088 LCD TV

1 Answer

Remotes no longer work


I had this exact same problem. After a week or so it started responding to the remote control again. Then after a couple of days it stopped responding. This problem came and went for about a month, then one day the entire TV went dead. When I powered it on, the green light appeared for 2 seconds followed by a sequence of 6 flashing red lights that repeated. I brought my set in to a repair shop and they replaced the power supply board. That fixed the problem and now the TV powers up and responds to the remote control again. Total charge was $250. That was very disappointing for a $1,500 TV that was only 18 months old. I'm going to let Philips know how disappointed I am in their product!

May 28, 2008 | Philips 37PF7320A 37 in. HD-Ready LCD...

1 Answer

My Sharp Aquos TV has stopped responding to remote control(s)


Unplugging my TV for 15 seconds (longer actually - at least a minute) made the remote and the satellite TV remote both work again with the TV.  Thanks for the tip!

May 14, 2008 | Flat Panel Televisions

Not finding what you are looking for?
Flat Panel Televisions Logo

Related Topics:

65 people viewed this question

Ask a Question

Usually answered in minutes!

Top LG Flat Panel Televisions Experts

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Les Dickinson
Les Dickinson

Level 3 Expert

18298 Answers

The Knight
The Knight

Level 3 Expert

68229 Answers

Are you a LG Flat Panel Television Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...