Question about Mitsubishi VS-50605 50" Rear Projection Television

1 Answer

Cost to replace signal board

Tv jumps like crazy... after several hours.. it stops..

Was told the Signal board needs to be replace.. does anyone know how much this usually cost to replace or rebuild?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 4,234 Answers

The signal board is not likely to be the cause of this. I'll research this a bit and update this with some sugestions. Can you solder?

Dan

Posted on Feb 11, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

On my Mitsubishi WD-82840 DLP TV for the first hour of operation I'm seeing green pixelations in the darkest sections of the image displaying on the TV.


May mean the DLP chip is either not getting the proper level of black signal until the controller board has warmed up, or the DLP chip itself is not completely responding to the controller signals. After thoroughly warming up the problem goes away. This is a sign of aging of the parts. Diagnosing and correcting that type of problem is a challenge. Regards.

Dec 07, 2015 | Mitsubishi WD Projection Televisions

1 Answer

Have rca hd52w59 that has mind of its own. Turns volume down but not up. Turns TV on but not off. Flashes menu screen on and off. Screen formats changes, etc etc. Is the TV shot or is there a relative easy...


Thats a very common problem with that model which is caused by the small signal board needing replacement. Several version of small signal boards were used in that chassis but the people at www.tvrepairworld.com have replacement signal boards and will help you determine which version you require for your specific version if your not sure.

Jan 04, 2012 | RCA HD52W59 HDTV Projection Television

1 Answer

Picture looks like a rainbow with an arc in the middle


Thats the small signal board. You can get a new replacement small signal board at the following link for several hundred dollars cheaper. Leave them a emai with what you need they respond quickly. www.tvrepairworld.com

Aug 12, 2009 | RCA HD52W59 HDTV Projection Television

1 Answer

RCA D52W23 convergence chip


THERE is no convergence ICs on these sets it does have convergence board it has serveral ALuminnin heat sinks on it If comcast was at fault it would have fried your SSB board which will shut TV down Cost of Board is 352.00

Feb 13, 2009 | RCA D52W23 52" HDTV CRT TV

2 Answers

RCA D52W119 Projection tv


You have 3 capacitors on deflection board ,ck them cp150,cp111 cp114.cp150 2200uf 15v green/gold writing.

Oct 13, 2008 | RCA D52W19 52" Rear Projection Television

1 Answer

Part Number


the part number is 259307 for the ITC222 chassis its over 300.00 for the board although you can get one at the following link for about half that price. They dont list them, But they have them you just have to leave a email this is what the small signal board looks like. http://servicemanuals.vstore.ca/444d206.jpg

Jul 31, 2008 | RCA D52W19 52" Rear Projection Television

1 Answer

Signal board questions


replacing the board requires no set up so it should run after replacement. as for the other problems that is unknown until you replace the parts you know are bad. it tough to say if any other boards were affected.

Feb 14, 2008 | Hitachi 51F510 51" Rear Projection...

1 Answer

TV shuts off automatically


I Can Assure You That This Problem Is Associated With 2 Capicators On The Power Supply Board.
 

Aug 24, 2007 | Mitsubishi WD-52725 52". Rear Projection...

1 Answer

Bouncing Picture on WS48511 MITSUBISHI PROJECTION TV


I have seen this symptom a lot recently. There is a 9 volt regulator on the small signal board, and the output voltage on this IC has dropped down to about 8 volts, which causes that symptom. Replacing that regulator should cure your problem, and when I make a housecall for a set like that I charge $150, although I hear that the average service center charges a lot more than that. I also believe that it is never a good idea to leave a projection TV on all the time, so whoever told you that has no idea what they are talking about.

Jul 05, 2007 | Mitsubishi WS48511 48" Rear Projection...

2 Answers

Bad signal board or something else?


You weren't very specific about your problem, but assuming you've tried different inputs and tried messing with the convergence setting, it may indeed be the signal board, and you may need to have it replaced. BTW these sets also have an issue with the dynamic focus circuit and with crt fluid leakage. Make sure that you do not have a fluid on one of the crt boards. And as always with repairmen, a second opinion couldn't hurt.

Apr 04, 2006 | Samsung HCN653W 65" Rear Projection...

Not finding what you are looking for?
Mitsubishi VS-50605 50" Rear Projection Television Logo

Related Topics:

301 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Projection Televisions Experts

matt martin
matt martin

Level 3 Expert

1191 Answers

Jaime Hernandez

Level 3 Expert

2267 Answers

The Knight
The Knight

Level 3 Expert

68368 Answers

Are you a Mitsubishi Projection Television Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...