Question about Palm Zire 71 Handheld

1 Answer

Zire won't come on

Every time i turn my zire on screen readsuse stylus to tap center of target could it need to b charged

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

  • Expert
  • 164 Answers

You need to follow the procedure to calibrate the digitizer.

If the screen does not respond to the stylus, then the digitizer is defective and needs to be replaced.

Best regards,

Posted on Jul 25, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Palm zire stylus not working


Try doing a soft reset on the pda, this will usually resolve the issue. Then reperform the aliginment task.

Jun 10, 2012 | Palm Zire Mono M150 Handheld

1 Answer

I dont have the owners manual for zire m150 and cant get past the touch the target . it asking me to used stylus to tap center of target.. i did and it just goes from upper left corner to lower right...


You could try

operatingguides.com

if you need a user manual
or

servicemanuals.co.uk

if you want the schematics etc

We've used them in the past and found them very good.

Also if it is not listed then ask via the link and they
will probably be able to get it for you.

Jul 17, 2011 | Palm Zire Mono M150 Handheld

1 Answer

My Palm Zire M150 touch screen is badly misaligned. How do I reset the alignment?


the screen says use stylus to tap center of target ...i do that and it goes to upper left corner i tap and it goes lower right corner and back and forth between the to corners?

Mar 01, 2011 | Palm Zire Mono M150 Handheld

1 Answer

My palm pilot keeps telling me to , use stylus to top center of target,then it goes to top left and then to bottom right,over and over ,what do i do to get into the programs?


Either you have a protective cover that is too thick or your digitizer is or has failed.

You can try a differant stylus to touch the targets. On my 31 it was stubborn the odd time and would do this from time to time. With a sharper stylus point and being very careful about touching the exact center of the target it would get out of this.

Apr 05, 2010 | Palm Zire 31 Handheld

1 Answer

My palm Vx asks me to tap center of target but doesn't respond


If there is no response anywhere at any time then you probably have to replace the digitizer. Also if you have a plastic protector sheet take that off and try it.

Mar 01, 2010 | Palm Vx Handheld

1 Answer

Zire 71 screen does not sense stylus input -- even after performing a reset.


HI,
Try doing a hard reset. This will erase everything on your zire and restore it to brand new settings. To do a hard reset make sure you have everything backup on your palm desktop. Here are the steps for the hard reset:


1. Hold down the power button and then depress the small hole in the back with the tip of your stylus2.gif.

2. Continue to hold them both in until you see the Palm2.gif logo.

3. Let go of both of them and then follow the onscreen directions. You will want to answer yes and use the 5 way navigation button on the bottom of your pda and hit up so that is completes the reset. After that you will have to set up your touch screen and go through the tapping the target. After you have gone through all this then do a hotsync. It should clear up your problem. Best wishes.

Oct 10, 2009 | Palm Zire 71 Handheld

1 Answer

Tapping target problem


My friends Tungsten E2 does that, he has to just keep tapping the target over and over until it procceds, thats all he can do, and it generly does go to the next screen, after a loooong while.

Aug 19, 2008 | Palm Zire 31 Handheld

1 Answer

Palm Zire 71


The top plastic digitizer is defective.

It needs to be replaced.

There are several sources on-line to buy such digitizer part.

Best regards,

Jul 14, 2008 | Palm Zire 71 Handheld

1 Answer

Zire 71 digitizer


I have the same problem and discovered that the right side of the screen had "spread". When I draw a line from the left to the right using Note Pad, the line ends up about 1/4 inch above the stylus. What I had to do is touch the stylus about 1/8th of an inch above the center of the digitizer target on the right side.

Sep 20, 2007 | Palm Zire 71 Handheld

Not finding what you are looking for?
Palm Zire 71 Handheld Logo

Related Topics:

172 people viewed this question

Ask a Question

Usually answered in minutes!

Top Palm PDAs Experts

MUSTAFA BULENT...
MUSTAFA BULENT...

Level 2 Expert

166 Answers

David Payne
David Payne

Level 3 Expert

13437 Answers

Nataly Roberts
Nataly Roberts

Level 2 Expert

30 Answers

Are you a Palm PDA Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...