Question about Marantz SR-5200 Receiver

1 Answer

Marantz SR5200 receiver works only with remote not manually

My Marantz SR5200 works only when operated with the remote control. Except for the power button, volume control, none of the buttons work when pressed manually on the unit itself.

Posted by on

  • Anonymous Mar 18, 2014

    Hi,
    I have a problem with updating firmware in Marantz M-CR603. Although power and network cables are connected and working properly the device fails with message:
    Updating fail: 10
    17min 00%
    System

    I was trying to reset it by pressing few different combinations of buttons, when powering the device up, but none of them were working. Even the one from the manual (volume up and volume down simultaneously). All the device is doing, after powering it up,is entering the firmware update mode which it fails finally.
    Is there a way to make it alive?

×

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 336 Answers

Check for a stuck/jammed switch, press each switch if one doesn't make a normal click sound or it doesn't move at all that's your problem.
If that's not it check the owners manual for how to reset the receiver (not all manuals will tell you how to reset it) Another way to reset it is to short the memory cap, but that is better left to a tech.

Posted on Feb 13, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Marantz SR5200 Turns on and off by itself


Thermal cutoff is operating. There is excessive heat being generated on the heat sinks of the Amp. This happens when there is a shorted output transistor or a speaker load changing.

Nov 09, 2017 | Marantz Audio Players & Recorders

1 Answer

MARANTZ sr5200 Left Speaker larger sound right speaker


If you are saying that the left side is LOUDER than the right it could be DC offset on the recording or it could be phasing issues.

Feb 15, 2017 | Marantz Audio Players & Recorders

1 Answer

Hi my infrared remote control did not work from one day to the next. I tried each bugfixing from the operators manual. I changed batteries and the position to the receiver (receiver: sr4021). Are ther...


Read this procedure to possibly fix the remote:

http://remotes.com/remotes/servlet/rs?a=Display&contents=help_deadremote&uuid=A12963989782821

They also sell replacement remotes but I'd also look on eBay as they are always cheaper. I've seen whole systems WITH the remote that are cheaper than a replacement remote alone.

May 02, 2011 | Marantz SR4021

1 Answer

Can't turn on and off without manually going to unit. Have remote rc18sr. System still rocks, however went online to try for a new remote, i guess this is obsolete.


Marantz RC18SR Remote Control RC-18SR

Item condition: Used

Time left: 21h 0m 48s (Feb 17, 201111:51:43 PST)

http://cgi.ebay.com/Marantz-RC18SR-Remote-Control-RC-18SR-/180627142815?pt=LH_DefaultDomain_0&hash=item2a0e37789f

Marantz RC18SR Remote Control RC-18SR Item condition: Used Time left: 21h 0m 48s (Feb 17, 201111:51:43 PST)

Feb 16, 2011 | Marantz AV-560 Receiver

1 Answer

Remote control work very slowly and sometime do not work


Please follow the troubleshooting steps:
  1. Remove the batteries from the remote control.
  2. Press each button on the remote control twice.
  3. Make sure none of the buttons on the remote control are jammed.
  4. Install fresh batteries into the remote control.
  5. Make sure nothing is blocking the Infrared (IR) sensor on the TV.
  6. On the remote control, press the TV FUNCTION button.
  7. Press the POWER button and other buttons to test the operation.
  8. Try using the remote control at varying distances from the TV.
  9. Power reset the TV by follow the steps:
  • Unplug the television power cord from the electrical outlet.
  • Let the television remain without power for 60 seconds.
  • Plug the power cord back into the electrical outlet.

Jan 09, 2011 | Philips 32PF9964 32 in. Television

1 Answer

DWIN tv, Marantz receiver and Dish system. Three different remotes needed to control. One for On/Off of the tv, one for the volume and the third for the Dish network. What is the best way to get to one...


Youdo have the ability to program your current DISH Network remote to all of yourcomponents. If you decide you would like to do so, I have included instructionsto assist you in programming your remote. In order to program your remote toyour DWIN television without the remote code, (I'm sorry unfortunately I wasunable to locate a remote code for a DWIN Tv L) you can complete what we refer to asa "Power Scan," to do this you would complete the following steps. 1. Withthe desired equipment on, press and hold the correct Mode button until all modebutton backlights illuminate, then release. (In this case the mode button willbe "TV") 2. Pressand release the Power button. 3. Pressthe Up button once a second while pointing the remote at the desired equipment. Note: If the code for the equipment comes up, theequipment will power off. 4. Pressthe POUND (#) button. If the codeentered is valid for the remote, the mode light flashes three times.

-In addition, you can also program the remote to yourMarantz receiver this can be done by pressing and holding the AUX botton inupper left corner of remote next to the SAT button.
-Press & hold AUX until all the other mode buttonslight up, then release AUX button, all the other mode buttons should turn off,only AUX button should be blinking now,
-While AUX button is blinking enter in the remote code742 for the Marantz receiver and then press the # key (pound key.) Afterpressing the # key on your remote, the AUX mode button should blink 3 timesmeaning the programming has been completed successfully. While still in AUXmode try any function on the remote, such as turning the volume up or down onyour Marantz receiver. The DISH Network remote should now be programmed tocontrol the receiver.
-If the 742 code doesn't program the DISH Network remotesuccessfully you can also try each of the following using the same procedures, 743,651, or 740. After completing the power scan to program the DISHNetwork remote to your DWIN t.v, & completing the AUX mode buttonprogramming, the remote should now work for your TV to powere on and off, theMarantz amplifier- to control the volume, and the DISH Network receiver. Hopethis helps! -Kirstie DISH Network

Oct 04, 2010 | DISH Network IR Remote Control

2 Answers

My marantz sr5200 powered off and won't turn back on. What do I do? There is a light flashing red. this is not an overheating problem or fuse problem. It happened when I was trying to program the...


try to reset the memory circuits, the info on them may be corrupted, try this:
1 disconnect the plug from the AC line supply
2 wait 10 minutes then, reconnect the plug to the AC
outlet
3 try to operate the equipment.

now.. if above does not work you may have to contact the manufacturer as
the issue could be related with the internal circuitry.

good luck!

Apr 11, 2010 | Marantz SR-5000

1 Answer

Dish network code for a viore, volume/power not working


You can power scan for the code.
Turn ON the electronic device you want to program the remote to control.
Press the Mode button( sat,tv,dvd,aux) on the remote until the appropriate mode light is flashing.

Press the Power button. The mode light will stop flashing and stay lit.
Press the Up or Down arrow button to set the remote to the next code. The Down arrow button scans backward and the Up arrow button scans forward.
When the correct code is reached, the device (whether a TV, VCR, or other) will turn off.

Press the pound key button to store the code in the remote control memory. If the code is valid for your remote, the mode light will blink 3 times.
Turn the device back ON by pressing the Power button.
Press sat mode key once you power back on the tv to be able to operate the receiver box.
Try some other functions to make sure you have the correct code. Occasionally the Power button may work when others do not.
If the other buttons work you are finished.

.
If the other buttons do not work, repeat the previous steps. The scan will resume from the last code stored.
The mode light will flash rapidly when the scan has returned to the starting point and all codes have been tested for that mode. The remote control may not control some device models.

Apr 05, 2010 | Toymax Viore 42 in. Plasma TV

1 Answer

My marantz sr5200 dont reproduce dobly digital signals , maybe junt 2 channels.


I have the Marantz SR5200, unable to get the Set-up / t.tone button to work, don't have the instructions,

Mar 19, 2010 | Marantz SR-5200 Receiver

Not finding what you are looking for?
Marantz SR-5200 Receiver Logo

Related Topics:

608 people viewed this question

Ask a Question

Usually answered in minutes!

Top Marantz Audio Players & Recorders Experts

The Knight
The Knight

Level 3 Expert

74459 Answers

 Grubhead
Grubhead

Level 3 Expert

5190 Answers

Electro Med Services...
Electro Med Services...

Level 3 Expert

6694 Answers

Are you a Marantz Audio Player and Recorder Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...