Question about Amana NAV5805A Top Load Washer

1 Answer

Lwd27aw belt replacing

Replace belt

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 130 Answers

PULL THE FRONT LOWER PANEL, BELT SHOULD BE IN FRONT OF YOU. YOU MAY NEED TO DROP THE MOTOR TO GET THE BELT ON

Posted on Feb 10, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Belt replacement


belt goes on the bottom of dryer. look up your model on internet on replacing belt . its pretty easy. if old belt is still on make a diagram of how belt goes on, also take a pic.

Jan 30, 2014 | Amana DLW330RA Top Load Washer

1 Answer

How do a replace the belt on the drum of my indesit washer dryer


REMOVE THE SOCKET FROM THE WALL OUTLET.
To replace a belt that passes over the drum on a dryer you need to be able to pass the new belt over either the back or the front of the drum. This entails removing the front panel to clear the whole drum or loosening off the rear bearing support to pass the belt under it so that the belt can be passed over the drum. From there it is just a case of passing the belt over the motor pulley and replacing all the parts. Select which will be easier on your machine. After replacing everything but the top panel, make sure that the belt is correctly installed by turning the drum several revolutions by hand and ensuring that the belt is running true and still on the motor pulley. Replace the top cover and you are set to go.

Feb 19, 2011 | Indesit Washing Machines

1 Answer

Toro 521 snowblower instruction to replace belts


Remove bottom cover(4bolts) 3/8"Remove plastic housing cover (mine had 2 bolts)3/8"Loosen belt guide bolt.1/2" rotate guide away from belt.I used a pipe wrench to hold main shaft and removed drive pulley.Replace drive belt as you return pulley onto shaft.Replace auger belt.Align belt guidesSet handle adjustmentsReplace coversTest and hope for warm weather, I live in BuffaloHope this helps

Jan 01, 2011 | Washing Machines

1 Answer

How do i replace the belt


FIRST MAKE SURE THE POWER IS OFF THEN REMOVE ALL THE SKREWS IN THE PANEL AND REMOVE IT , LOCATE THE DRIVE BELT TENSOINER AND LOOSEN REMOVE THE BELT AND TAKE IT TO A PLUMMERS SUPLY STORE FOR REPLACEMENT WHEN FITTING THE NEW BELT MAKE SURE THE TENSION IS TIGHT BUT GIVES A LITTLE .

Nov 16, 2009 | Washing Machines

1 Answer

My whirlpoolultimate care 11 will not spin , look under bottom and their is a belt like item hanging. could this be the problem?


YES THAT IS THE DRIVE BELT DRUM YOU CAN SEE, IT SOUNDS LIKE THE BELT HAS BROKE DU TO WARE AND TEAR AND YOU NEED TO REPLACE THIS BELT TO FIX THE PROBLEM , TO REPLACE THE BELT IS STRAIT FORWARD , REMOVE THE PANEL AND LOCATE THE BELT TAKE THIS BELT WITH YOU TO A PLUMMERS SUPPLY STORE TO GET THE RIGHT SIZE BELT REPLACEMENT, WHEN REFITTING NEW BELT MAKE SURE YOU GET THE TENSION CORRECT.

Nov 11, 2009 | Whirlpool Ultimate Care II LSQ9549L Top...

1 Answer

Belts need replacing how do i do it?


Pull washer out a couple of feet and tilt it back, lifting the front. Rest against the wall. The belts are on the bottom. Remove the drain pump belt, and you'll get to the drive belt. The motor is installed on a plate and held by a spring. To install the belts easier, push motor towards the transmission pulley when installing new belts. Part numbers: 211124 for the pump belt, and 211125 for the drive belt. Set of both belts: 12112425.
The set of both belts includes an instruction sheet also.
Coupon "New10" takes 10% off.
Good luck

Oct 31, 2009 | Maytag Dependable Care LAT9416

1 Answer

The washer is making a terrible racquet. The belt seems to be rubbing; black stuff all over the place. Can I adjust the belt?


The belt will have to be replaced. There is no adjustment, per se. There is a belt tensioner that keeps the appropriate tension on the belt. It can be checked when the belt is replaced to see if it's failure caused the belt problem, but it may just be a belt that has failed and needs replaced because of age or structural breakdown.. Hope this helped and best wishes.

Aug 14, 2009 | Whirlpool Duet GHW9150P Front Load Washer

1 Answer

I need to replace the belt


You shouldn't have to remove the pump to replace the belt. The motor mount can be loosened and the motor moved so the belt will fit over all pulleys without removing the components.

Loosen motor, move it in, install belt, move motor out to correct belt tension, tighten motor mounts.

May 28, 2009 | Amana 3.2 cu. ft. Top-Load Washer

1 Answer

Replacing belt


Put The Belt On The Motor First Then Put What You Can Get Of The Belt On The Other Pulley And Turn It. It Will Give You The Anchorage Needed To Put The Belt Back In Position. If This Doesn't Help Let Me Know And I Will Further Assist You.
Sincerely,
Michael Scott

Feb 10, 2009 | Amana 3.2 cu. ft. Top-Load Washer

1 Answer

Amana Washer model number LWD27AW


Try pulling the knob out & rotating counter-clockwise to unscrew it.

Nov 28, 2006 | Amana NAV5805A Top Load Washer

Not finding what you are looking for?
Amana NAV5805A Top Load Washer Logo

Related Topics:

149 people viewed this question

Ask a Question

Usually answered in minutes!

Top Amana Washing Machines Experts

Dan Webster
Dan Webster

Level 3 Expert

8147 Answers

Richard Roth
Richard Roth

Level 3 Expert

9472 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Are you an Amana Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...