Question about GE 1101P DVD Player

1 Answer

Can not activate GE 24921 remote control

By following the direct code entry procedure, at step 2, I pressed the device button (DVD) and the indicator light did blinks but then stopped. It does not stay lit. Therefore, I can not enter the code to make it work. Please advise what is wrong?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

  • Contributor
  • 6 Answers

This problem is possibly happening in Step 1. You must hold the Setup button untill the light stays on. If the light stays on until you press the DVD button, then you need to replace the batteries.

Posted on Feb 21, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I need the control remote code


irect Code Entry for GE remotes with 4 digit codes

The following is a short tutorial on entering the codes on GE 4 digit code universal remotes. See also this page for general GE remote code entering instructions!
Step 1: Press and hold the "SETUP" button until the red indicator stays on, then release.
Step 2: Press and release the desired Mode button (VCR, TV etc.). The red indicator will blink, then stays lit.
Step 3: Enter the 4 digit code for your device. After a valid code entry, the red indicator turns off. For an invalid code, the red indicator flashes!
Step 4: With your device on, press "CHANNEL UP" or "CHANNEL DOWN." If the device responds, no further programming is required. If some buttons do not operate your device, try one of the other codes for your brand. Note, when all codes have been searched the red indicator flashes rapidly for 3 seconds.

Code Search instructions

If your device does not respond to any of the codes listed with your equipment, or your brand is not listed, try the following steps:
Step 1: Manually turn on the device to be controlled.
Step 2: Press and hold the "SETUP" button until the red indicator stays on, then release.
Step 3: Press and release the desired Mode button (VCR, TV etc.). The red indicator will blink once, then stays on.
Step 4: Press the "CHANNEL UP" button repeatedly until the device to be controlled changes channel. The red indicator will blink, then stays lit.
Step 5: Press and release "MUTE" button to install the code. The indicator light goes off.
Generally it's best to store VCR codes under the VCR button, cable codes under CBL, and so on. If you want to store a VCR code under CBL, etc., first follow the procedure for Direct Code Entry and press CBL in step 2 of Direct Code Entry, then enter any VCR code in step 3 of Direct Code Entry. Then follow the steps above for Code Search.

Sep 13, 2013 | RCA DRC230N DVD Player

1 Answer

Region unlock method for this modek


Direct Code Entry
  1. Press and hold the SETUP button until the red indicator stays on, then release the SETUP button.
  2. Press and release the desired Mode button (TV, VCR, etc.). The red indicator blinks, then stays lit.
  3. Enter the 4 digit code from the code tables. Note: after a valid code entry, the red indicator turns off. For an invalid code, the red indicator flashes.
  4. With your device on, press CHANNEL UP. If the device responds, no further programming is required. Note: If some buttons do not operate your device, try one of the other codes for your brand.
    Code Search Method
    If after trying the direct code entry, you can't synchronise the device with remote control, try code search method as follows:
    1. Manually turn on the device (TV, VCR, etc.) to be controlled.
    2. Press and hold the SETUP button until the red indicator stays on, then release the SETUP button.
    3. Press and release the desired Mode button (TV, VCR, etc.). The red indicator blinks once, then stays on.
    4. Press the CHANNEL UP button repeatedly (up to 300 times) until the device to be controlled changes channel. The red indicator blinks, then stays lit.
    5. Press and release MUTE to install the code. The indicator light goes off.
    Most users will want to store VCR codes under the VCR button, Cable codes under CBL, etc. If you want to store a VCR code under CBL, etc., first follow the procedure for Direct Code Entry and press CBL in step 2 of Direct Code Entry, then enter ANY VCR code in step 3 of Direct Code Entry. Then follow the steps above for Code Search.

Apr 07, 2012 | Televison & Video

1 Answer

Gflight@yahoo.comdo you have the universal remote code for emerson dvd vcr combo ewd2202


Hello
Unversal remote setup codes for Emerson DVD/VCR combo are:
0456 [0458 0227]
Where the code is listed as [### ###] the first is for the DVD and the second is for the VCR. Otherwise just the one code operates both the DVD and the VCR.
Direct Code Entry
  1. Press and hold the SETUP button until the red indicator stays on, then release the SETUP button.
  2. Press and release the desired Mode button (TV, VCR, etc.). The red indicator blinks, then stays lit.
  3. Enter the 4 digit code from the code tables. Note: after a valid code entry, the red indicator turns off. For an invalid code, the red indicator flashes.
  4. With your device on, press CHANNEL UP. If the device responds, no further programming is required. Note: If some buttons do not operate your device, try one of the other codes for your brand.
Code Search If after trying "Direct Code Entry" your device does not respond, or if your brand is not listed, try doing a search of the code library for your code by following these steps.
  1. Manually turn on the device (TV, VCR, etc.) to be controlled.
  2. Press and hold the SETUP button until the red indicator stays on, then release the SETUP button.
  3. Press and release the desired Mode button (TV, VCR, etc.). The red indicator blinks once, then stays on.
  4. Press the CHANNEL UP button repeatedly (up to 300 times) until the device to be controlled changes channel. The red indicator blinks, then stays lit.
  5. Press and release MUTE to install the code. The indicator light goes off.
Most users will want to store VCR codes under the VCR button, Cable codes under CBL, etc. If you want to store a VCR code under CBL, etc., first follow the procedure for Direct Code Entry and press CBL in step 2 of Direct Code Entry, then enter ANY VCR code in step 3 of Direct Code Entry. Then follow the steps above for Code Search.
OK

Aug 13, 2011 | Emerson EWD2202 DVD Player/VCR

2 Answers

I need the code for a magnavox dvd vcr combo. its the quick set up code or codes. its for little leaps learning steps. i cant find the manual for it.


Hello
Setup codes for Magnavox DVD/VCR are:
0456
[0914 0286] [0969 0286]
Where the code is listed as [### ###] the first is for the DVD and the second is for the VCR. Otherwise just the one code operates both the DVD and the VCR.
Direct Code Entry
  1. Press and hold the SETUP button until the red indicator stays on, then release the SETUP button.
  2. Press and release the desired Mode button (TV, VCR, etc.). The red indicator blinks, then stays lit.
  3. Enter the 4 digit code from the code tables. Note: after a valid code entry, the red indicator turns off. For an invalid code, the red indicator flashes.
  4. With your device on, press CHANNEL UP. If the device responds, no further programming is required. Note: If some buttons do not operate your device, try one of the other codes for your brand.
Code Search If after trying "Direct Code Entry" your device does not respond, or if your brand is not listed, try doing a search of the code library for your code by following these steps.
  1. Manually turn on the device (TV, VCR, etc.) to be controlled.
  2. Press and hold the SETUP button until the red indicator stays on, then release the SETUP button.
  3. Press and release the desired Mode button (TV, VCR, etc.). The red indicator blinks once, then stays on.
  4. Press the CHANNEL UP button repeatedly (up to 300 times) until the device to be controlled changes channel. The red indicator blinks, then stays lit.
  5. Press and release MUTE to install the code. The indicator light goes off.
Most users will want to store VCR codes under the VCR button, Cable codes under CBL, etc. If you want to store a VCR code under CBL, etc., first follow the procedure for Direct Code Entry and press CBL in step 2 of Direct Code Entry, then enter ANY VCR code in step 3 of Direct Code Entry. Then follow the steps above for Code Search.
OK.

Jul 19, 2011 | Philips Magnavox DVD/VCR Dual Player

1 Answer

Have rcu310bb remote. Need how to use with rc5220p dvd player


Hi
RCA codes to check with RCA RC5220P are:
3150, 3356, 3363, 3372, 3412, 3423, 3424, 3426, 3443, 3470, 3480, HTIB: 3444, Portable: 3163

1* Manually turn on the component

you want the remote to control.

2* Locate the enclosed Code Lists.

Find the list for the component you

wish to program. Find your

component's brand. You will see a

listing of four-digit codes for each

brand. If your brand isn't listed, use

one of the Code Search methods to

program the remote control. (Refer

to pages 7 and 9 for Manual and

Auto Code Search methods.)

3* Press and hold the component key

(TV, VCR•DVD, SAT•CBL) you

wishto program. The illuminated

ON•OFF key turns on and

remains on. If you release the

component key at any time

during the Direct Code Entry

procedure, the illuminated

ON•OFF key blinks four times,

and the process is exited.

4* While holding down the

component key, consult the Code

Lists for the four-digit code that

corresponds to your component's

brand and use the number keys

(0-9) on the keypad to enter it.

While you are pressing the

numbers, the illuminated

ON•OFF key turns off.

5* After the fourth number is

entered, the illuminated ON•OFF

key turns on. At this time, release

the component key. If the

illuminated ON•OFF key turns

off, you have entered a valid code

and have followed the correct
procedure for Direct Code Entry.

If you enter a code number that is not

in the Code Lists or you do not follow

all of the steps for Direct Code Entry,

the illuminated ON•OFF key blinks

four times when the component key

is released. This is an indication that

a programming error has occurred.

In that case, repeat the Direct Code
Entry process from step 3.
OK.

Jul 10, 2011 | RCA RC5220P DVD Player

1 Answer

I need to program the SV2000 VCR/DVD combo to work with the WOW cable universal remote(ATLAS OCAO 5-Device Remote Control, M1056). Please give me the secret codes. :)


Hello
Check with these codes:
0456 [0458 0227]
Where the code is listed as [### ###] the first is for the DVD and the second is for the VCR. Otherwise just the one code operates both the DVD and the VCR

Direct Code Entry
  1. Press and hold the SETUP button until the red indicator stays on, then release the SETUP button.
  2. Press and release the desired Mode button (TV, VCR, etc.). The red indicator blinks, then stays lit.
  3. Enter the 4 digit code from the code tables. Note: after a valid code entry, the red indicator turns off. For an invalid code, the red indicator flashes.
  4. With your device on, press CHANNEL UP. If the device responds, no further programming is required. Note: If some buttons do not operate your device, try one of the other codes for your brand.
Code Search If after trying "Direct Code Entry" your device does not respond, or if your brand is not listed, try doing a search of the code library for your code by following these steps.
  1. Manually turn on the device (TV, VCR, etc.) to be controlled.
  2. Press and hold the SETUP button until the red indicator stays on, then release the SETUP button.
  3. Press and release the desired Mode button (TV, VCR, etc.). The red indicator blinks once, then stays on.
  4. Press the CHANNEL UP button repeatedly (up to 300 times) until the device to be controlled changes channel. The red indicator blinks, then stays lit.
  5. Press and release MUTE to install the code. The indicator light goes off.
Most users will want to store VCR codes under the VCR button, Cable codes under CBL, etc. If you want to store a VCR code under CBL, etc., first follow the procedure for Direct Code Entry and press CBL in step 2 of Direct Code Entry, then enter ANY VCR code in step 3 of Direct Code Entry. Then follow the steps above for Code Search
OK.

Jun 19, 2011 | Funai PY90VG DVD Player/VCR

1 Answer

Do you have to reprogram the remote after changing the batteries?


Hi,

It depends on the remote model.

After changing the battery please check weather the remote works or else you need to reprogramme it.

For programming please follow the below steps

1.Press the Setup button on your the universal remote and continue to hold it down until the indicator light stops flashing and remains solid. Release the Setup button.

2.Press the Mode button for the type of device you want to program on your Philips universal remote, such as the TV or DVD button.

3.Release it immediately and make sure the indicator light is illuminated.
4.Enter the first possible four-digit code on the universal remote, and then press another button on the remote to see if the device is now programmed, such as the volume control or power button.
5.If the device responds, you have successfully programmed your Philips universal remote.
6. If not, turn the device off and back on and follow the steps again using the next code on the list. Repeat until the device successfully responds


Thanx

Jul 25, 2010 | Philips Magnavox DVD/VCR Dual Player

1 Answer

Philips dvp3150v vcr/dvd combo "code" for universal remotes


Hi,
try following codes
RCA universal remote controller:
021, 022, 062, 096, 124(VCR)
162, 356, 357(DVD)
Philips Magnavox Universal Remote PM335
130 226 330 536 631 734 738(VCR)
441 442 943(DVD)
many direct codes doesn't work ,code searching method all ways work better but irritating
STEPS:
1. Press and hold CODE SEARCH
until the INDICATOR LIGHT
lights, then release CODE
SEARCH.
2. Press and release the device
button for the device’s code
you are retrieving (TV,VCR or
DBS•CABLE). The INDICATOR
LIGHT will blink once then
remain lit.
Note: For AUX, press DVD•AUX
then the device button for the
code you are retrieving.
3. Press and release CODE
SEARCH. The INDICATOR
LIGHT will turn off.
4. Starting with 0 on the keypad,
press the number buttons in
order (0-9) until the
INDICATOR LIGHT blinks.
5. The number which causes the
INDICATOR LIGHT to blink is
the first digit of your code.
6. Repeat step 4 until you have
retrieved all three numbers in code

NOTE
:
if any of the above works note down code used in small bit of paper and place it in the battery chamber(safe place)

May 09, 2010 | Philips DVDR3435V/37 DVD Recorder/VCR

1 Answer

I have a universal remote control device(G.E.) that i want to use for a Sanyo DWM395 DVD Player. i lost the instructions with the codes though. can you please help me with this issue? thanks!


Try this through your Remote, it should automatically search & detect devices automatically without the need to know the codes.


USING CODE SEARCH FUNCTION
If your TV, VCR, DVD, etc. does not respond after you have tried all the codes
for your brand or if your brand is not listed, try searching for your codes by
following the steps below.
1. Turn on the device you wish to program.
2. Press and hold CODE SEARCH/SETUP until the INDICATOR
LIGHT lights, then release.
3. Press and release the device button for the device you are
programming (TV, VCR, DVD, etc.). The INDICATOR LIGHT will
blink once then remain lit. For AUX, press AUX then the device
button you are assigning to AUX.
4. Press and release POWER until your device turns off. Wait at least
2 seconds between each time you press POWER. Important: You
may have to press POWER up to 250 times.
5. When your device turns off press the ENTER/SAVE button. The
INDICATOR LIGHT will go off.

Dec 03, 2008 | Sanyo DWM395 DVD Player

7 Answers

Code for apex tv through philips universal remote


Go to www.urc.philips.com/
Follow the steps..its easy. It will ask for the model of your remote which you will find where your batteries are located..The code I used for my APEX tv was 0023.. to load the code first hold the setup button until the red light stays on..then press tv or whatever mode you are setting up..then enter the code and if the red light goes off it is the right code and you should then press channel up to see if it works...If this code doesn't work the site above offers other codes.. Hope this helps!!

Aug 30, 2008 | Apex Digital ADV3800 DVD Player/VCR

Not finding what you are looking for?
GE 1101P DVD Player Logo

Related Topics:

168 people viewed this question

Ask a Question

Usually answered in minutes!

Top GE Televison & Video Experts

The Knight
The Knight

Level 3 Expert

69718 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

matt martin
matt martin

Level 3 Expert

1198 Answers

Are you a GE Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...