Question about D-Link RangeBooster G WBR-2310 Wireless Router (WBR2310)

1 Answer

Lost password lost security pass code to link up with main computer

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 2 Answers

Using a paper clip there is a port on the back reset the router back to the defaults the login will be admin there is no password then leave it blank

Posted on Feb 10, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Lost my pass code for dlink


If the default password on the D-Link has been changed then-
To reset the D-Link back to the default settings -
Press and hold the RESET button at the back of the router with the power ONuntil the LEDs flash at the time the release the RESET button. (firmware version was 3.00, and upgraded to3.05)Connect a LAN cable from the D-Link to your laptop/computer'sLAN port, open the browser on your laptop/computer and enter the D-Link's configurationURL..
http://192.168.0.1
The default login = admin
The default PW = blank (just press Enter)You can now change the default admin password.
You can now configure the wireless settings.
Now configure the wireless card in your computer/laptop withthe router's wireless settings.To secure your wireless network from unauthorized access,please click on this link and follow my instructions :-http://www.fixya.com/support/r3559128-wireless_router_security

Jul 14, 2012 | Linksys Wireless-G Broadband Router

1 Answer

Pass code is not working


Connect your router to computer with ethernet cable then you can access it with following default link. http://192.168.1.1 or http://192.168.0.1 or http://192.168.15.1 or http://192.168.2.1 If you are not able to access it with above ip then check your computers ip address gateway ip is your router ip try with it. Then it ask for user name and password. Type user as "admin" and password as "admin" or "password" or blank. Then you can see configuration page of router. If you are still not able to access router with above ip then you need to RESET it for that press RESET button for 10 seconds it is in back side of router then all settings defaults..Then you can access it with above method. . Then click on wireless->wireless security->WEP security there is code password note down it or enter new password then save setting s and restart router. then you can connect wireless with new password. Let me know if you need further assistance. Thanks for using FixYa.

Sep 06, 2011 | D-Link DIR-615 Wireless Router

1 Answer

Set security pass code


After connecting modem(1) to router (2) connect your computer (3).
(4) Power on your modem, wait for modem to cycle(approx 2 minutes)
(5) Power on your router.
(6) Insert your CD - Click Router Setup & follow steps to setup secure wireless network...
NO CD DRIVE INSTALLATION
IN YOUR BROWSER ADDRESS FIELD:
http://www.routerlogin.net & click ENTER

1. Enter the router User Name admin & default password password to open your router's main settings page.
2. Main settings page, you'll be asked if you want to "Check for Update". Click Cancel. ( you can always check for new firmware after you're connected to internet)
3 Choose first menu item on left; Setup Wizard & make sure YES is selected
click NEXT, follow prompts complete setup.
SET UP WIRELESS SECURITY
  • 1. From main page choose Wireless settings
  • 2. Name your network- something easy to remember (Hint* People see it when you are up & running, write it down as well!) {The default name is NETGEAR}
  • 3. Select your security method. NETGEAR recommends: WPA-PSK(TKIP +WPA2-PSK (AES).
  • THEN, enter a Pass-phrase {Write down also, you will get e-mail confirming registration etc... But, BSTS.
  • NOTE: Both your Network Name (SSID) & Pass phrase are case sensitive. Network name, Security method & Pass phrase must all be the same on all the wireless devices connected to your router.
  • 4. Click APPLY & close your browser.
Depending on your cable/internet provider- if these instructions don't do it,
one of their agents should be kind enough to assist?
I was lucky enough to have them do it with me over the phone, after I had surgery & got sick of looking of the thing in the box in my floor!
Good Luck!

Dec 02, 2010 | NetGear Routers

2 Answers

My husband bought a dlink router (it says dgl-4500 on it) and i cant figure out how to use it to get wireless internet for my new laptop....i have three "codes" he wrote down- a "router pass", a "network...


Router password is the password to access the router settings.
SSID is the network name. When you try to connect to the wireless network on your laptop, you will see this network name.
If your network is secured network then it will ask you for the network key or the password. You need to enter the ' security key '.

Click Here for step by step by instructions

Sep 11, 2010 | D-Link DGL-4500 Wireless Router

1 Answer

Lost security code and forgot pass word


If you forget your security code and password of the router, you can just reset it to factory settings by pressing and holding the reset button with a paper clip or any pointed objects.

Aug 05, 2010 | Routers

1 Answer

I have 3 comuters one has lost the wep code and i


Goto any one of the computers that are working

Open Router Setup by typing http://192.168.2.1 on the address bar of internet explorer

On the left under wireless click security

Leave the password blank and click submit

You can find your WEP password here


Jul 12, 2010 | Belkin Routers

2 Answers

Password trouble


I NEED THE SECURITY CODE FOR MY d-lINK dir-601

Jun 26, 2010 | D-Link Xtreme N DIR-655 Wireless Router

1 Answer

I think some one has got my pass key code and is using my router for free internet, how do i check this and change the pass key.


First connect your router to computer with ethernet cable.
Then you can access it with following link
http://192.168.1.1
or
http://192.168.0.1
type user as "admin" and password as "admin" or blank or "password"
then go to wi fi security check your WEP code it is your security key to connect wi fi network.
Change it and then save settings and restart router.
Let me know if you need more assistance.
Thanks

Oct 05, 2009 | U.S. Robotics MAXg USR5461 (738168036790)...

2 Answers

Lost security code for D link wireless router


usually your notebook should connect itself as the password would already be set up in the connections properties.

 

If you know how to get into the wireless routers settings, go to the security menu and turn off the security encryption (wep or WPA PSK) and then use a different password when you turn security back on again.

 

Or make sure you have the settings for your isp and press the reset button on the back to delete all the settings 

Oct 12, 2007 | Linksys Wireless-G Broadband Router

Not finding what you are looking for?
D-Link RangeBooster G  WBR-2310 Wireless Router (WBR2310) Logo

Related Topics:

114 people viewed this question

Ask a Question

Usually answered in minutes!

Top D-Link Routers Experts

Les Dickinson
Les Dickinson

Level 3 Expert

18299 Answers

Mike

Level 3 Expert

4331 Answers

Christopher Thrash

Level 3 Expert

425 Answers

Are you a D-Link Router Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...