Question about GE WBSR3140DW Top Load Washer

1 Answer

Washer fills slow only in the rinse cycle

During the initial filling of the machine, both the hot and cold water fill at a full rate.When it gets to the rinse cycle it takes about 45 minutes to fill.The water barely trickles in.The machine also makes a buzzing sound when it gets to that cycle.Do you think this may be a controler problem?? If it where the valve or screens it wouldn't fill normal in the wash cycle, Would it??If it is a control problem what part would I need to replace the whole controller??Dial assembly?? GE slow rinse; barely pours and usually stops lights blink then I push to restart

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 12 Answers

Need a model # to get exact part you will need at rinse most washer go straight cold so I would say water inlet valve if humming sound is present

Posted on Apr 28, 2017

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
catriver
  • 878 Answers

SOURCE: Washer fills slow only in the rinse cycle

The first thing I would do is remove the hoses from the inlet valve and make sure the screens are not clogged in the valve. On some models the valve will compensate on fill opening both hot and cold. It will not do this on cold rinse. Before ordering any controls check this out first. If it's still the same I tend to believe it's a valve problem. The buzzing you are hearing is the valve. Catriver, post back.

Posted on Aug 06, 2006

watugot
  • 290 Answers

SOURCE: GE Washer-Doesn't Fill When it Supposed to.

It is most likely a pressure switch. This is the water level switch. As water fills the tub, air pressure builds up in the rubber hose going to the switch. When the pressure is high enough for the water level setting, it trips the switch and puts the unit in wash cycle. Remove the control and start the machine. While it is agitating, remove the hose from the switch and see if the washer starts filling. If so, blow through the hose and see if something has clogged it. If you have a volt/ohm meter you can check across the terminals while you blow into the switch to see if it is working. Let me know what you find out.

Posted on Oct 19, 2007

  • 1028 Answers

SOURCE: Washer fills slow only in the rinse cycle

ck and clean screens first both sides be sure hoses are not reversed timer has no affect on fill rate if screens are clean replace valve

Posted on Sep 20, 2008

  • 1 Answer

SOURCE: GE Front Load Washer

Removing the lower front panel (3 screws nearest floor), and opening the round, white water pump filter cap (be ready to catch about 2 gallons of water!) is the best place to start. All you need is a Phillips head screwdriver and a large, flat pan (deep turkey tray works well)!

YOU WILL NOT BELIEVE what I found in my filter housing this morning (see photo below)!

490ccb1.jpg

The washer is working fine now, although I may go back and remove the entire water pump so it can be dismantled, thoroughly cleaned, and reinstalled.

Posted on Sep 22, 2008

BNewberry
  • 93 Answers

SOURCE: water barely trickles out for rinse cycle

Hello,

It sounds like you have some buildup in the cold water valve screen. Where the hose connects to the washer there should be a screen inside the valve. Remove the cold water hose from the washer and clear any debri on the valve screen.

If this doesn't fix the slow cold water flow then you will have to replace the whole water valve assembly. The water valve is the piece that the hoses connect too and supply water to the washer.

If you have anymore questions about this please ask. I will be more than happy to help you out.

Thanks

Posted on Jan 12, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Kenmore 70 series washer


If you can see a constant water pressure from the hot and cold, chances are the water solenoid valves are ok.

I would look towards resetting to factory and checking the main control unit.

May 11, 2014 | Washing Machines

1 Answer

WDSR2120J washer will not fill in rinse cycle


possible 3 solutions for this problem 1 could be the cold fill solenoid 2 could be brushes in motor 3 could be main pcb

Feb 20, 2013 | Washing Machines

1 Answer

Not getting enough water during rinse cycle


In the rinse cycle it will use cold only to rinse with.
You need to see how fast the water is going into the machine on rinse
Things that can effect slow fill, low water pressure, Faulty cold valve
water hose & valve filters clogged, Kinked hose

Feb 21, 2012 | Fisher and Paykel IWL12 Top Load Washer

1 Answer

Kenmore front-load washer stops at rinse cycle


When the washer initially fills for the wash, is it only hot water entering the drum? Try switching the water temperature between hot and cold as it fills. If any of them show little or no water getting through, it sounds too easy but check to make sure water supply taps are on, and that the cold/hot fill hoses aren't reversed. Remove the fill hoses and check any of the screen filters for blockage (in the hoses and in the inlet water valve). When the machine stops and waits to fill but all you hear is a hum, it sounds like there is power going to the valve but water is not able to get through it.
Good luck!

Mar 03, 2009 | Kenmore 43142 Front Load Washer

1 Answer

Cold water is slow when filling for rinse cycle


Turn off the cold water.
Remove the cold water hose from the machine.
Look inside the cold water inlet on the machine and clean the debris from the screen.
Problem solved.

Feb 22, 2009 | GE WJRR4170E Top Load Washer

2 Answers

Cold water will not stop filling during rinse


while the unit is filling in the warm cycle. reach behind and shut off the hot water tap.I bet the water flow stops filling, if so, you would need to change the inlet valve on the machine. You see, in warm, if the cold is not filling, you still hear the hot filling and the unit will advance. The rinse cycles are mostly "cold" only. if the valve is not opening it will not allow it to advance from the rinse section on the board.

Good luck!

Feb 16, 2009 | Maytag Neptune MAH5500B Front Load Washer

1 Answer

Washer won't fill in rinse cycle


REPLACE YOUR WATER INLET VALVE(HOT,COLD WHERE HOSES ARE)IT'S NOT OPENING ALL THE WAY TO LET THE WATER FILL UP FAST,LET ME KNOW HOW YOU DO-MIKE

Oct 19, 2008 | Maytag Washing Machines

1 Answer

Washer fills slow only in the rinse cycle


ck and clean screens first both sides be sure hoses are not reversed timer has no affect on fill rate if screens are clean replace valve

Sep 19, 2008 | Kenmore 24032\24036 Top Load Washer

2 Answers

Does Not Rinse


Check each temperature during initial wash fill. Set to hot water, is hot water coming out? Set to cold water, is cold water coming out? The rinse cycle is cold only. If cold water is not working machine will just stop at rinse.

If cold water not working:
Disconnect cold water hose from machine. Inspect the filter screen on the cold water connection. DO NOT REMOVE SCREEN. If full of debris, use a spray bottle with a hard spray to remove debris. If unable to remove or cold is still not working, replace valve.

Jun 14, 2008 | Whirlpool LSR6332K Top Load Washer

3 Answers

Washer fills slow only in the rinse cycle


The first thing I would do is remove the hoses from the inlet valve and make sure the screens are not clogged in the valve. On some models the valve will compensate on fill opening both hot and cold. It will not do this on cold rinse. Before ordering any controls check this out first. If it's still the same I tend to believe it's a valve problem. The buzzing you are hearing is the valve. Catriver, post back.

Aug 06, 2006 | Whirlpool LSQ9600L Top Load Washer

Not finding what you are looking for?
GE WBSR3140DW Top Load Washer Logo

Related Topics:

110 people viewed this question

Ask a Question

Usually answered in minutes!

Top GE Washing Machines Experts

Dan Webster
Dan Webster

Level 3 Expert

8220 Answers

Tim Whalen

Level 3 Expert

3074 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

Are you a GE Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...