Question about Whirlpool AWM8123 Front Load Washer

2 Answers

Whirlpool awm 8125/3 fault code FH

Machine goes through the washing programme then with 20 mins aprox left it will stop. The error code FH flashes on the top panel and nothing else happens

Posted by on

  • Anonymous Feb 26, 2009

    whirlpool AWO3761 fault code FH after 10 minutes of cycle then machine stops

  • Anonymous Mar 17, 2014

    Whirlpool awm8113 displays FH code but water feed to machine ok

×

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 1 Answer

Probably too late, but here it goes:
FH means some cicle is taking too long time.
Replace the inlet electrical valve. It probably wont open enough and the water flow is not enough to fill to level in time. This should cost you 10€ and is easily done by anyone.
Just remove the top of the machine (two bolts on the rear and slide to the back), disconnect the valve (electrical and water input and output), push the lockers and twist the valve free.

Posted on Jun 02, 2009

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

F18

Posted on Nov 18, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Indesit IWD7145K Washing Machine Error code F06 flashing on digital display + all program indicator lights. What does this mean. There is no such error code in the troubleshooting section of the manua


F06 - Door lock fault
Issue: Washing machine door cannot be opened or closed/when the door is closed the machine the programme will not start.
Advice: If your washing machine door will not close, please check for any obstructions in the door lock.
OR,
Switch off the device. Disconnect power. Wait about 3 minutes.
Open the door, then close. Reconnect device to the network.
Start device.

Cause: Door lock fails to close / open door lock triac open / closed,
frequency signal fault

Dado

Feb 12, 2015 | Indesit Washing Machines

1 Answer

Display periodically flashes H20


The faulot is related to the incoming water supply.
Chaek inlet hose for restriction or low water pressure.

Jan 19, 2010 | Washing Machines

2 Answers

Washing machine whirlpool awm8123/1 stopped and FH on display


If after 30 seconds the control does not detect water entering machine, the valves will be turned off and the error code will be displayed. OR If the control has turned the water valves on and after 8 minutes the flow sensor has detected 10.5 gallons of water passing through it, but has not detected the pressure switch trip, the valves will be turned off and the error code will flash. Press PAUSE/CANCEL twice to clear the display.
check the fill hose screens or you my have to repalce water valve make sure water is turned on....

Sep 19, 2009 | Whirlpool AWM8123 Front Load Washer

1 Answer

We have a whirlpool 6th Sense AWM 6145/3 which has just started stopping during the wash cycle and on the digital display the letters F H come up. We rent our property and have moved several times and have...


FH is the code for no water flowing in...

is there water flowing in?

if there is none, the water solenoid is the problem,

if there is water going in, then the flow switch is the problem.

here is the transcript from the web..

FH ERROR CODE

No water detected entering machine or Pressure switch trip not detected.
If after 30 seconds the control does not detect water entering machine and then valves
will be turned off and the error code will be displayed.
Or
If the control has turned the water valves on and after 8 minutes the flow sensor has
detected 48liters of water passing through it, but has not detected the pressure switch
trip, the valves will be turned off and the error code will flash.

and here is their solution

water source opened
flowmeter
pressoswitch
wiring to valves, pump,
flowmeter, pressoswitch
hoses


either one of those parts...

tnx 4 using fixya,

drcool


Sep 13, 2008 | Whirlpool Washing Machines

1 Answer

Help with whirlpool awm 8103/1


Okay, ther manufacturer recommends unplugging the washer for at least 30 minutes to reset the computer. It could be you have a momentary glitch causing some problems. If you still have the same problem after leaving the washer unplugged, the following link explains the "FH" error code:

http://www.fixya.com/support/r615354-fh_error_code_whirlpool_duet_kenmore

If your clothes are stuck inside and you still cannot get them out because the door will not unlock, you will have to use the manual release to open the door. The next link explains how:

http://www.fixya.com/support/r622155-kenmore_elite_whirlpool_duet_door_jammed

I hope this helps you. If you require additional assistance, please let me know.

Aug 27, 2008 | Whirlpool GHW9300 Duet Washer

Not finding what you are looking for?
Whirlpool AWM8123 Front Load Washer Logo

2,412 people viewed this question

Ask a Question

Usually answered in minutes!

Top Whirlpool Washing Machines Experts

Dan Webster
Dan Webster

Level 3 Expert

8147 Answers

Richard Roth
Richard Roth

Level 3 Expert

9472 Answers

Mike Cairns
Mike Cairns

Level 3 Expert

3053 Answers

Are you a Whirlpool Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...