Question about Whirlpool LSB6200KQ Top Load Washer

1 Answer

Whirlpoor top load washer cold water wont stop flowing

It wont stop unflowing even when the cycle is stopped manually or unpluged fromt he wall. I have to shut the water source off to get it to stop, or it will overflow all over my basement floor.

Posted by on

  • mk_tune Feb 07, 2009

    thanks alot for the advice i will try that right away.

  • Anonymous May 18, 2009

    Whirlpool top load washer cold water won't stop flowing . You have to shut off water manually

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 640 Answers

Repace you inlet vavle..onthejob of (FILL VAVLE)

Posted on Feb 07, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Water wont cut off


Does the water run if you push the timer dial in to stop the cycle or does it run even if you unplug the washer?

Dec 31, 2011 | Whirlpool LSR7333 Top Load Washer

1 Answer

WATER IN WASHER WONT SHUT OFF


Hi and welcone to FixYa. I am Kelly. When water wont shut off no matter what you do the problem is inside of the water valve assy. Usually there is a small bit of debris in the diaphram center hole that is holding the water passage open.

Here is what you can try to do to clear if BEFORE replacing the eater Valve.

1. Get a bucket
2. Turn off both water supply hoses momentarily
3. Set the water temp to warm
4. Remove ONE hose from the wall connection and place the hose in a the bucket.
5. Turn on the remaning connected hose/
6. Start machine fill cycle and tap the hose connection at the water valve on the back of the machine with either a screw driver or hammer handle.

Timer OFF

REVERSE HOSE CONNECTIONS ON THE WALL CONNECTION.

7. Place the other hose in the bucket
8. Start Fill cycle.
9. Again tap the hose connection at the water valve
10. Stop timer.
11. Reconnect both hoses and test for water flow with timer off.
12. Start fill cycle
13. Rapidly select hot and cold wash water.
14. STOP fill cycle.
15. Remove each hose individually from the water valve one at a time.
16. Use a knive blade and remove the inlet screen from the water valve. Wash screen under slowly running water rubbing it clean with your fingers. Re install screen. Reconnect water hose.
17. Repeat step 16 for opposite hose and screen.
18. Turn on water supply.
19. Test for proper filling and water stopping by starting and stopping fill cycle.

If it works you got lucky. If you still have the problem you will need to change the water valve. Either one of these water valves will work on your machine:
http://www.repairclinic.com/Appliance-Parts?s=t-PAV2300-%3d%3dc292d509361

Thanks for using FixYa.

Kelly


That is about it




Jun 05, 2010 | Maytag PAV2300 Top Load Washer

1 Answer

My washer goes through the cycle but the cold


This sounds like your water fill valve is bad and will need to be replaced.

Feb 01, 2010 | Maytag LAT2300 Top Load Washer

1 Answer

Cold water runs continuously at end of cycle


If yo9u were to unplug the machine at that point and the water continues to run in you have a bad water valve. If it stops when yoou unplug it, it may be the timer. Would have to test to see if voltage is present at the valve in the second scenario,. Water valve part# is WH13x10024 @ $51.00

Apr 08, 2009 | GE WJSR2070B Top Load Washer

1 Answer

Washer- Hot water wont stop flowing


you will have to replace the multi valve inside the washer where the lines come in, not too hard if you can use tools and find all the hold own bolts/ screws. the part can be a little pricey so you may want to take it to a repair shop. make sure that you UNPLUG first!

Feb 24, 2009 | Kenmore 15864/15862 Top Load Washer

1 Answer

Error code 20 on Kenmore C47192 front loading washer


F20 is an indication of low water flow. Check that the screens in the hoses or the valve at the back of the washer are not clogged. Mineral buildup in the water lines can break free, causing the screens to plug.

Press Stop twice to cancel any cycles, unplug the washer while you check the hoses, then plug back in.

If you find plugged hoses, then you should not have any additional problems. If you didn't, check to make sure there is adequate flow from the wall valve by removing the washer drain line from the wall drain pipe, put the washer end of the water hoses into the drain pipe one at a time, and turn on the faucet to assure there is good flow. Be sure to hold the hose into the drain pipe.

Jan 19, 2009 | Kenmore 43142 Front Load Washer

2 Answers

Washer won't stop filling


if you can turn the washer off while it is still filling. and the water continues to enter the machine you have a bad inlet valve.
Do me a favor turn the washer to fill, with the washer still running unplug from the wall. If the water is still entering the unit you have a bad inlet valve

Jan 05, 2009 | Roper RAS8445KQ Top Load Washer

1 Answer

Water in my washing machine


it sounds like you have a leaking water valve, you will have to replace the mixing valve, For now turn the water off at the wall suppling water to the machine. When you want to use the washer turn on water, when its done with the cycle turn the water off.

Note: unplugging the machine will not stop the water from running

May 13, 2008 | Amana 3.2 cu. ft. Top-Load Washer

Not finding what you are looking for?
Whirlpool LSB6200KQ Top Load Washer Logo

Related Topics:

208 people viewed this question

Ask a Question

Usually answered in minutes!

Top Whirlpool Washing Machines Experts

Dan Webster
Dan Webster

Level 3 Expert

8147 Answers

Richard Roth
Richard Roth

Level 3 Expert

9472 Answers

Mike Cairns
Mike Cairns

Level 3 Expert

3053 Answers

Are you a Whirlpool Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...