Question about Roper RAX4232KQ Top Load Washer

1 Answer

Roper RAX4232KQ0 maker loud noise at spin cycle and then stops

My wife washed 3 pairs of really muddy jeans and the next load we washed the washer starting making a very loud noise at spin cycle. After the loud noise starts it stops after a few seconds and doesn't try to spin at all

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 12 Answers

There are a few things that can go wrong, If the washer doesn't adgitate or spin then probably the coupler is broken, lean the washer back and look under the machine between the motor and transmission you will find the coupler. (very common)

Coupler Part# 285753A $22.95

If its agitating but not spinning, check the lid switch, (easy check just listen for the click when you shut the lid, Or you can bypass it with a jumper wire under the console there are only 2 screw that hold the console down they are philips and either located in the front lower corners or the back lower corners)

Lid switch Part# 3949247 $42.95

If lid switch is good and the motor still doesnt run you might have a bad timer (RARE)
Timer Part# 3954563 $95.95

If you can hear the motor running but its not spinning and you have rulled out the coupler then your probably looking at a clutch (common problem) either the clutch isnt grabbing or the brake isnt releasing both problems solved with the clutch kit

Clutch kit Part# 285785 $44.95

Worst case your looking at a transmission, (uncommon) to rule out, make sure its agitating, then put washer in spin cycle. look under the washer to see if the clutch bell is spinning. if its not then you will need a transmission.

Trans Part# 3360629 $172.95

if its making loud noises when it stops spinnig then the block is bad.

Block Part# 389140 $14.95

Posted on Feb 07, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I have a kenmore 800 series washer that makes a loud slamming noise at the end of the spin cycle. If you lift the lid during the spin cycle the basket slams to a halt immediately. It actually moves the...


Those parts you can check
1/ strings holding the drum were broken causing drum unbalancing when it spins.
2/ Drum bearing also gone. (noise)
3/ 3 slides that located underneath the triangle frame need replaced.

Oct 22, 2013 | Washing Machines

2 Answers

My whirlpool duet washer hammers very loud when it spins. The outside of the machine doesn't seem to vibrate much but it is very loud.


That is a common occurrence with dryers such as this one. Even though it sounds bad, it is harmless. If it really bothers, you can re-balance the load and it should reduce the vibration.

Jul 29, 2008 | Whirlpool Washing Machines

1 Answer

Roper washing machine makes grinding noise on spin cycle but the tub doesn't turn


It sounds like you have a motor coupling that is broken. There are videos on YouTube to show you how to repair this. Search for "motor coupling repair on direct drive".

Nov 26, 2012 | Roper RAS8445KQ Top Load Washer

1 Answer

My washer makes a lot of noise while on the spin cycle


If the washload is not distributed evenly around the agitator when the final spin cycle starts, the tub will be unbalanced and will wobble and thump loudly. This is especially true if you are washing something heavy such as a rug or jeans. You may have to distribute the load more than once to get results.

Sep 04, 2012 | Roper Washing Machines

1 Answer

I have a top load Roper washer that won't spin.Any ideas?


That sounds like a bad drum bearing, check and eventually replace the drum bearing.

Dec 28, 2008 | Roper RAS8445KQ Top Load Washer

1 Answer

Roper RAX4232KQ0 washer grinds


Yes they are only about 40 dollars but if your washer doesn't agitate then the problem would be the "drive motor to transmission coupling"

Dec 24, 2008 | Roper RAS8445KQ Top Load Washer

2 Answers

Washer makes loud knocking noise


I think that the drum bearings have gone on the machine..

To open the door and spin the empty drum quickly by hand and you should hear the noise or say a less amplifed one.. You can also move the inner drum up and down to see if there is something wrong with it..

Sep 28, 2008 | Roper RAS6233KQ Top Load Washer

1 Answer

Noisy Spin Cycle


hi there,

Most noises from a washing machine occur during the spin cycle. If you hear loud thumping/or sound
during the spin, the load of clothes may have become unbalanced. Stop the washer and
redistribute the clothes, then re-start it. Repeat these steps if necessary.

Jun 12, 2008 | Whirlpool LSR9434PQ Top Load Washer

2 Answers

Frigidaire top-load washer Loud noise during spin


its either the upper spin bearing or lower spin bearing. the upper can be replaced by itself but the lower requires the transmission the be replaced

Nov 20, 2007 | Frigidaire FWS833A Top Load Washer

Not finding what you are looking for?
Roper RAX4232KQ Top Load Washer Logo

675 people viewed this question

Ask a Question

Usually answered in minutes!

Top Roper Washing Machines Experts

Dan Webster
Dan Webster

Level 3 Expert

8147 Answers

Richard Roth
Richard Roth

Level 3 Expert

9472 Answers

Mike Cairns
Mike Cairns

Level 3 Expert

3053 Answers

Are you a Roper Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...