Question about Kenmore Oasis HE 27082 Top Load Washer

2 Answers

Error Code LD flashes

The washer started just fine and then it was going to start the rinse cycle and starting beeping and flashing LD. It wont let me do anything it wouldnt even turn off. The lid unlocked but it would not shut off and it just beeped at me. It says LD and I am not exactly sure what that means or if I should call and get it repaired or what?

Posted by on

  • 4 more comments 
  • rmullen578 Mar 18, 2009

    My washer was also in a rinse and then "LD" flashed,now it wont do anything.I did get rid of the "LD" but the unit still wont turn on ,all I get is a buzzing noise

  • Caj8754 Mar 24, 2009

    My Oasis's is 2 yrs old and I have spent hundreds of dollars for the same problem. Every few months the LD code comes up and the water will not drain from the washer and it is stuck. Sears has offered no explanation and they only keep charging me for there service! I will never buy from Sears again!

  • papickard Apr 02, 2009

    I have the same problem but washer is only 5 weeks old. The repair man came out and says that it needs a new computer board and the water pump is out. 331.00 in repairs. Glad for warrenty. Sears is going to replace the washer but i just wonder about this machine. I love the large capacity and it does wash clothes well. I had to learn how to use it though. Hope this helps.

  • marjo_elaine Apr 20, 2009

    Ld displays whenever I wash bedding. This has happened at least six times this past year!! I've had Sears out several times but the memory board doesn't save the error so they say they can't fix it. I've already had the control panel replaced . . . unplugging it for two days seems to workbut who can wait for their washer to"come back on" for that long. I'll never buy Kenore again!!!

  • giggles6436 May 04, 2009

    I had no problems out of my washer until I called the 800 # to get the board replaced. ONE week later I get the LD flashing and buzzing nothing happening. The guy comes out and he says he thinks it the control panel but whirlpool thinks its just a bad board. He ordered a new board AGAIN I just got it today now I have to call for another service appt. We shall see what becomes of this.....

  • Anonymous May 08, 2009

    I have the same problem with the LD showing up, unplugging it for 24 hrs or even up to 72 hours does seem to help this situation, but it still does continue. Yes, I've called Sears many times with this complaint, I did have the control board replaced once, but now it is happening all over again, and the warranty period is over. I agree with alot of you, this is a constant problem, and I will never buy from Sears again.

×

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 3 Answers

Today (4/3/09) I got a letter from Sears. They will replace the electronic control board (you know, the F-51 business) for FREE, in warranty or not. Serial #s for the Bad Board are: CS48 - CS52 or CT01-CT49. Call Sears at 800-847-9083. The voices of all of us have finally been heard!

Posted on Apr 04, 2009

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 99 Answers

This is joyce:
lets try the simple solution first, unplug the unit first, for 1 min, and then replug it, this resets the unit. then if this works try to put on rinse cycle and get ride of all the soap suds in the washer pump. use a little oil in a empty washer run and then reset washer on regular load and rerun, see if this does the trick. if not you may need to call a tech. if you need assistance please let me know
thanks
joyce

Posted on Feb 06, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why does it beep through the entire. Wash cycle. No code showing.


Whirlpool Duet GHW9150P Front Load Washer Beeping ...

www.fixya.com > ... > Whirlpool Duet GHW9150P Front Load Washer
Question about Whirlpool duet Washing Machines ... my front loader is not workingwhirlpool washer flashes and beeps will not finish a cycle 1 Beep/E10--Error: Water... It beeps through the wash and rinse cycle every couple of minutes. ... Cycle signal which tells you that the cycle is complete beeps through the entire cycle.

[PDF]front-loading automatic washer use and care ... - Whirlpool

www.whirlpool.com/.../U...

Translate this page Whirlpool Home AppliancesWash. This is the main portion of the wash cycle. You will see the washer tumble the load. ... Spin cycle. If the laundry is still wet, take half of the load out of the washer and try again. .... Using recommended AFFRESH® washer cleaner, add.

[PDF]DISHWASHER USER INSTRUCTIONS - Whirlpool

https://www.whirlpool.co...

Translate this page Whirlpool Home AppliancesThe first cycle using the sensor will run longer to calibrate the optical sensor. Rinse Aid. Using rinse aid will optimize your drying and wash performance. This dishwasher is ...... laundry detergent, hand soap, or dish detergent for hand washing .... models) you will experience more starts and stops throughout the entire cycle.

Continuous Beeping - Whirlpool Duet Sport Washer - The ...

appliantology.org > ... > The Laundry Appliance Repair Forum

Jan 25, 2016 | Whirlpool Washing Machines

1 Answer

Why won't my washer start a cycle? Start button LED just flashes. All other lights are steady. Door lock sounds like it engaged, but nothing happens.


There should be a way to enter the washing machine into service mode to view an error code. Check your user manual and then you should have your answer!

Jul 23, 2014 | Washing Machines

1 Answer

Code in digital display does not have a E in front of it


Please let me know if you can get a number after this - if so what number shows up?


Model differences:
• Better models have a digital readout display
• Good models do not have a digital readout display
In the Better Models line, the failure codes will appear in the display as an E followed by two numbers, a number and a letter
or two letters. The control will beep and the Door Lock, Wash, Rinse, Final Spin and Control indicator lights will flash.
Example: E14. To stop the flashing and beeping, the customer may touch the Pause Cancel button. The error code remains
stored in the control but once the problem is corrected, it does not effect the operation of the washer. If the failure is something
that the customer can correct (such as the water faucets being turned off), the washer will operate normally the next time it is
started.
In the Good Models line, the control signals the failure code by flashing the five indicator lights of Door Lock, Wash, Rinse,
Final Spin and Control for the first number or letter after the E and the Start indicator light for the second number or letter
after the E. When a failure occurs, the washer stops or pauses and the control beeps and flashes the five indicator lights to tell
the customer that a failure has occurred. To stop the flashing and beeping, the customer may touch the Pause Cancel button.
The error code remains stored in the control but once the problem is corrected, it does not effect the operation of the washer.
If the failure is something that the customer can correct (such as the water faucets being turned off), the washer will operate
normally the next time it is started.
To recall an error code,
• Wake the machine by pressing any button
• Wait 5 seconds
• Press and hold the Start and Pause Cancel buttons simultaneously
• All LEDs will go blank and after a few seconds the control will signal the stored code using audible beeps and blinking
LEDs. The control will repeatedly signal the code, as long as the Start and Pause Cancel buttons are pressed.
A two-second pause between repeats affords you the ability to make accurate counts to identify the correct error codes.
Please Note the following...... on a small number of washers with serial number prefix XC4,
if the previous procedure does not perform as specified, follow the option below:
• Follow all previous steps but instead of pressing Start and Pause Cancel buttons,
press and hold Options and Pause Cancel buttons.
If the washer is a Better Model, the error code will appear in the display. Troubleshoot problem by using charts on the
following pages.
If the washer is a Good Model, the five indicator lights of Door Lock, Wash, Rinse, Final Spin and Control will flash the
number of times for the first digit of the code and the Start indicator light will flash the number of times for the second digit.
Take
separate counts of each indicator light, then repeat to confirm in order to be accurate in identifying the proper error code.
The code is obtained by counting the number of times the lights flash. Example E24: The five indicator lights would flash twice
indicating the 2 and the START indicator light will flash four times indicating the 4. The five indicator lights and the START
indicator light start flashing at the same time.
The control will pause for 2 seconds, then repeat the code as long as the two buttons are pressed and held.
Note: A letter appearing in the code stands for a number higher than nine:
A = 10 B = 11 C = 12 D = 13 E = 14 F = 15
Example Code F1: the first digit would be 15 and the second digit would be 1. If this code would appear on a washer in the
Good model line, the five indicator lights would blink fifteen times and the START indicator light would blink once.

May 13, 2014 | Frigidaire ATF6000ES Front Load Washer

1 Answer

Wash machine quits mid cycle


Your Circuit Control Board is starting to Fail.... The Electrical Reset is the give away....

Mar 03, 2014 | Whirlpool Duet GHW9150P Front Load Washer

1 Answer

LD ERROR CODE AND WONT DRAIN LID WILL LOCK


try any button sequences yet . try holding start button and a cycle button hold both down to reset

Apr 01, 2013 | Whirlpool Cabrio WTW6800W Washer

2 Answers

My washer has a LD in the minute screen how do i get this off


LD is an error code relating to poor drainage. Check the drain hose and/or pipe for a clog. It's also possible that debris could have worked itself into the drain pump, causing a delay in drainage. Fixing your drainage problem will fix the LD error code.

Jun 05, 2011 | Whirlpool Cabrio WTW6600SBT Top Load...

1 Answer

My Whirlpool Duet ht Washer starts washing fine, it drains then it starts flashing FH and wont take in water for the rinse cycle. It does this for every cycle, it will wash fine but after it drains and is...


The first thing I would check is shut off the cold water valve at the wall and remove the hose at the washer.carefully pry out the little screen in the inlet and clean well,reconnect hose and turn water back on FH is a water inlet issue I am hoping that what is happening is that when the washer starts its wash cycle it is probably filling with warm (hot) and cold water at the same time even though it might be mostly hot,but when it comes time to rinse (cold water ) there is not enough to make the computer happy and you get your FH error.. Hope this Helps,,If not your probley looking at a new fill valve assy

Sep 16, 2010 | Whirlpool Duet GHW9150P Front Load Washer

1 Answer

E20 flashing mid cycle


E20 is a general error code to get to the real problem try this..
Reading Error Codes 1. Wake the washer by pressing any button. 2. Wait 5 seconds. 3. Press and hold the START/PAUSE and CANCEL buttons simultaneously. As long as the buttons are held, the failure code will appear in the display as an “E” followed by two numbers, a number and a letter or two letters. The control will beep and the Door Lock, Wash, Rinse, and Final Spin indicator lights will flash. let me know what code come up... hope it helps

Jul 01, 2009 | Zanussi ZWF1430W Front Load Washer

1 Answer

We have a Kenmore Oasis HE.It stopped during the rinse cycle


“F21” (AKA SD) is a Long (SLOW) Drain error (LD). If the drain time exceeds 8 minutes this error code will be displayed. In addition, a “SUDS” error may also be displayed. This may be an indication of a drain pump problem and/or clog in the drain line. You will need to check the following:


1.First, attempt to unplug the washer for at LEAST 30 minutes to reset the Central Control Unit (CCU). Sometimes this is all that is required to correct momentary glitches with the unit. If the error code returns, proceed to step 2.
2.Check the drain hose to make sure it is not kinked or clogged.
3.Check the electrical connections to the pump and ensure the pump is running.
4.Remove the drain pump filter and check for foreign objects and/or debris.
To check the drain pump, click on the following link for step-by-step instructions

http://www.fixya.com/support/r385844-checking_drain_pump_kenmore_elite_front

If the above procedures do not correct the problem, it is recommended by the manufacturer to replace the drain pump.

Thanks for using FixYa - a 4 THUMBS rating is appreciated for helping with your FREE question

May 16, 2009 | Kenmore Oasis HE 27082 Top Load Washer

2 Answers

Kenmore Oasis Ld code


LD code is long drain one of 2 things the drain pump is frozen and need to be replaced or there is somthing in the pump. Pull the washer a way from the wall a bit and get a bunch of towels. Lean the washer back against the wall towards the middle in the back you will see the pump take it apart and find the clog.
it can be assessed through the bottom.

May 06, 2009 | Kenmore Oasis 27042 Top Load Washer

Not finding what you are looking for?
Kenmore Oasis HE 27082 Top Load Washer Logo

536 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kenmore Washing Machines Experts

Richard Roth
Richard Roth

Level 3 Expert

9472 Answers

Archaeology
Archaeology

Level 3 Expert

662 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Kenmore Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...