Question about Zanussi ZWF1440 Front Load Washer

2 Answers

Zanussi jetsystem 1400 not drainng properly.........

Recently the clothes come out soaking wet....even with small loads and also on faster spin cycles. also sounds like the water is still in the drum after emptying//// please help!

Posted by on

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Zanussi Master
  • 3,463 Answers

There should be a filter located at bottom front right of washer behind a metal cover.
Press on cover to open, and remove filter by unscrewing anti -clockwise.
Also check outlet pipe is not blocked, more so if it goes into a sink waste connection, if it still leaves water in drum, then there is probably a partial blockage else where, which will require further investigation.
Please leave a fixya rating if my solution solves your problem.
Thankyou.

Posted on Feb 06, 2009

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Have you triend cleaning the filter.

Posted on Jun 24, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My model is zanussi easy iron washing machine capacity 6 kg spin 1400 ,my problem is that clothes are not getting dried, water remains in the clothes, what is the problem .


Your washing machine has a problem with the water unless it is washer-dryer. Water remains in the appliance because drain pump is not functioning properly and laundry is wet.

Dado

Mar 16, 2015 | Zanussi Washing Machines

1 Answer

My front load washer will not spin on the final spin cycle. Washer spins in wash and rinse cycle spin. Cloths are still soaking wet.


I appreciate your post, Rachel Kovach!

From my understanding your Frigidaire frontload washer is not spinning the final spinning and the clothes are still wet. If you washer is overloaded it will not spin properly to release the water out of the clothes. Also, a small load will cause your washer to not spin properly. You should additionally check the drain hose to make sure it not kinked or twisted that could cause your improper draining. If all that checks properly it could be an issue with your drain pump, motor, and control panel. I would suggest consulting with a technician for proper diagnosis and repair. This will help avoid unnecessary part purchases. -Matt

Nov 19, 2014 | Frigidaire Washing Machines

1 Answer

My zanussi jetsystem washer/dryer 1400 7kg load machine is not draining or spinning. It is unlocking so I can (at the moment anyway) get the load out, but the clothes have not drained or spun, therefore...


your machine require new set of carbon brushes, and it also may need the pump impeler checked to make sure there is nothing stuck in it such as hair pin safety pin or a wire from the under wired bra.....

Dec 04, 2009 | Zanussi ZWF1440 Front Load Washer

1 Answer

Zanussi jetsystem 1000 will not do anything


zanussi jetsystem 1000 has stopped spinning the wash ! its missing out the spinning program help ?

Oct 09, 2009 | Zanussi FJS1225W Front Load Washer

1 Answer

How to clean a Zanussi Jetsystem 1400


on my mums zanussi,, after opening door, machine had not drained and spined, closed door again could not get machine to go,, this time could not get door opened..there is power to machine.

May 19, 2009 | Zanussi Washing Machines

1 Answer

Dripping wet clothes


will be an UNBalanced load, maybe there was not enough clothes in the load so in that case the drum would not be able to distribute the load evenly so gave up on the spin, hence wet stuff!

Jan 27, 2009 | Haier Washing Machines

1 Answer

Zanussi jetsystem 1400 door seal


IF YOU REMOVE THE SEAL UNLESS YOU ARE AN ENGINEER YOU WILL FIND IT EXTREMELY DIFFICULT TO REFIT IT, TO CLEAN OUT THE SLUDGE USE A PLASTIC SCOURING PAD LIKE THE ONES USED FOR CLEANING DISHES. IFTHE SEAL IS BLACK THIS CANNOT BE CLEANED IT IS A CHEMICAL REACTION TO DETERGENTS ETC BUT IS NOT HARMFUL TO ITEMS BEING WASHED HOPE THIS WILL HELP.

Oct 09, 2008 | Zanussi ZWF1440 Front Load Washer

1 Answer

Load remains wet after full cycle (including spin @ 1400 rpm)


Hi Paul, Assuming it is pumping out ok, Unplug the machine tip it back at an angle, underneath you will see a black hose that is attached to the bottom of the drum, remove this, take out the ball and discard it and remove anything that may be in the filter, replace the hose and try the machine.

Nov 30, 2007 | Hotpoint WMA64 Front Load Washer

4 Answers

Zanussi jetsystem Turbodry 1200


It appears that you may have a faulty door interlock or a faulty PCB. pcb is not really a DIY job as some boards require proramming on certain versions. Regards Advisor

Oct 30, 2006 | Zanussi FJS1225W Front Load Washer

Not finding what you are looking for?
Zanussi ZWF1440 Front Load Washer Logo

1,327 people viewed this question

Ask a Question

Usually answered in minutes!

Top Zanussi Washing Machines Experts

Gerry Harvey
Gerry Harvey

Level 3 Expert

1456 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Richard Roth
Richard Roth

Level 3 Expert

9472 Answers

Are you a Zanussi Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...