Question about Sharp AR-5316 Advanced Digital Imager Copier

1 Answer

Call service message "call service" displays, what can I do to fix this problem?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 145 Answers

The firmware/software of the copiers seems to have gone bad. There is also a possibility of hardware failure.
Please rate me appropriately if you are satisfied with my answer,in case, if you want any clarification please get back to me.

Posted on Feb 05, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

IRC4080i printer. How do I correct error code E000007-0001?


Error Codes Relevant to Fixing/Pressure Belt Displacement Control

E007 Fixing belt displacement error

0001: Upper belt displacement fault. (Either the upper belt full displacement or the belt displacement sensor

fault.)

0002: Lower belt displacement fault. (Either the lower belt full displacement or the belt displacement sensor

fault.)

0101: Upper belt HP detection error.

0102: Lower belt HP detection error.

Note:

Adjust the fixing/pressure unit HP with the following service mode at the installation or when replacing the

fixing (pressure) belt.

COPIER > FUNCTION > FIXNG > FX-UHP-S
> FX-LHP-S

Points to Note When Replacing Fixing Unit

By executing the service mode, the alarm code is closed and the total rotation time is cleared. Thus, this mode

must be executed when replacing the fixing unit.

If the mode is not executed, the following symptoms will occur.

-The alarm code is not closed.

06-0002: Fixing unit life alarm (Caused by the belt displacement)

06-0004: Fixing unit life alarm (Caused by the torque up)

-Although the total rotation time of the replaced fixing assemble does not reach to the message threshold, the

machine wrongly recognize that it reaches to the threshold and displays the message.

Be sure not to execute the mode except at the installation and the fixing unit replacement. If not, an error
message may not be displayed when the fixing unit reaches to its life.

Sep 10, 2015 | Canon Printers & Copiers

1 Answer

How to fix Error 900.43 service RIP soft ware


Reset Factory Defaults.

1. Turn off the printer.
2. Press and hold and .
3. Turn on the printer.
4. Release the buttons when Performing Self Test displays.
The message CONFIG MENU displays on the top line of the operator panel.

If that does not fix this issue,With Error Code 900 displayed, press and . Post the complete list of Sub Error Codes on the display.

Jul 27, 2015 | IBM Infoprint 1532 Laser Printer

1 Answer

I have problem that the printer spooler is not displaying in the service. and when i add the printer then one message displayed that "your printer spooler service is not start. so what am i do for...


Hi,

Go to Start > Run, type in "services.msc", go down on the list till you see "Print Spooler", double-click, then click Start.

This should fix your issue.

Jul 22, 2011 | Xerox WorkCentre Pro 16fx Laser Printer

1 Answer

ERROR 59.06M


This error appears after the message Conditioning Drum is displayed and then after one page is printed. Conditioning Drum occurs approx every 100 pages printed. The 59 errors can appear either after the first message was posted to the front panel or after seven messages were displayed. Power cycling the printer can clear this error in the short term.
but at the end the printer will need service, here are the parts needed to fix the issue,Process cartridge drive assembly and the Ribbon cable between DC Controller and Print Driver

Aug 13, 2010 | HP LaserJet 9500n Printer

1 Answer

APPELER SERVICE TECHNIQUE




once the machine will display the message to the key you pressed simultaneously on the C & 8 the screen displays a C code numbers Example C 43 or C 44, which refers to an anomaly in the fixing unit and after we cancelled so on there are no defective parts.

Jan 21, 2010 | Toshiba E-Studio 160 All-In-One Laser...

4 Answers

Help with code sc546


need model.but in most it's a fuser prob.

Jul 05, 2008 | Gestetner DSm645 Digital Imaging System

2 Answers

Ricoh 1035 Display Messages


Empty waste toner in transfer unit on the right side door.

Jul 03, 2008 | Ricoh Aficio 1035 Copier

3 Answers

DISPLAY READS: 80 SERVICE (01E4)


An 80 service error is an MIO error. That is one of the accessories that is in the option slot in the rear of the machine.
  1. Turn of the machine.
  2. Unscrew and remove the Option card.
  3. Slide the card back in.
  4. Power the machine back up.

If the card is an option that ou do not use (such as a network card) You can just leave it out if you wish.
Please let me know if this helps.


Read more: My HP Lazer Jet 5M displays a message 80 SERVICE (01E4). - JustAnswer http://www.justanswer.com/printers/2zbop-hp-lazer-jet-5m-displays-message-80-service-01e4.html#AskAQuestionNow#ix..."#ixzz2Axr0Tbqj

Jun 16, 2008 | HP LaserJet 4 plus Printer

Not finding what you are looking for?
Sharp AR-5316 Advanced Digital Imager Copier Logo

Related Topics:

38 people viewed this question

Ask a Question

Usually answered in minutes!

Top Sharp Printers & Copiers Experts

George Mclaughlin

Level 2 Expert

330 Answers

Soulvisitor
Soulvisitor

Level 3 Expert

1113 Answers

Vito Suglio

Level 1 Expert

23 Answers

Are you a Sharp Printer and Copier Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...