Question about Ariston Technologies AWD121WH

1 Answer

Ariston a1436 wont finish cycle

Machine has to switched off and changed to another programe EG rinse but not emptying then have to go to drain then spin.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 14 Answers

Hello in your machines board seems to be shorting imbetween cycles, you will need to replace the board.

Posted on Feb 05, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

AEG Lavamat 74689 Update wont pump out


Possible that the program timer is faulty as it fails to switch on the pump in the required sequence. You can clean the contacts, check the power to the pump, trace the pump power line to the timer which can confirm the case. In such cases the timer must be replaced.

Jan 02, 2013 | Washing Machines

1 Answer

Machine will not finish cycle and water remains in washing machine


if the washing machine does not drain, continues to fill or fill too slowly the issue could be the pressure switch. if you have a multimeter use it to find any electrical issues if there is no reading the pressure switch needs to be replaced

Jan 29, 2011 | Ariston Technologies Ariston AWD12 Front...

2 Answers

It will do a full wash cycle but wont empty when finished


It is possible that the drain valve/pump is faulty if there is voltage on the valve/pump. If not the program controller board is faulty and must be checked. Check the drain hose and the connection to the outlet.

Jan 22, 2011 | Tricity Bendix Washing Machines

1 Answer

Ariston A1436 The machine begins to fill then empties and fails


Make sure that the top of the waste water pipe is at the correct height for the machine, typically around 30-34 inches from the floor (see your installation instructions). If it is any lower then it will start a siphoning action as soon as the water reaches the same level in the machine and never actually fill up and hence the cycle will not start. If the machine detects that insufficient water has entered the machine within a given time, typically 8 minutes, then if flags an error to the on board controller. If the error persists after the waste pipe height is corrected then check out the pressure switch for correct operation as if this is not triggered then the cycle will also not start or will halt almost immediately.

Oct 25, 2009 | Washing Machines

1 Answer

Hotpoint Aquarius cycle not finishing with f02 error


Dont think its pressure switch.if sticks one way machine overfills the other brings on heater with empty drum..Could be fauly rinse solonoid valve...Check with multimeter coil should read around3k ohms..good luck

Sep 29, 2009 | Hotpoint Ariston Aquarius WD420 Front Load...

2 Answers

Dial continuously turning


hiya
to reset the dial, switch the power off, then turn the dial to a dot on the selection then switch the power on, the light should flash about 3-4 times this should be it reset.

for the machine to start doing this mid cyle though usually indicates something is wrong, i would hazard a guess at the pump filter is blocked and the mahine was trying to drain at the time it started clicking.

the best thing to do is empty the machine manually by placing the outlet hose into a bucket or large dish, once empty remove the plastic kick plate on the bottom of the machine and behind this you will find the filter.
before you unscrew the filter you will need to place some towels or old cloths on the floor as there will still be water left in the pipes, remove filter and any foreign objects (possibly coins, hair clips etc) and then screw back in. job done.

hope this helps

please dont forget to rate the helpfulness of this reply, thanks kj

Aug 02, 2008 | Ariston Technologies Ariston AWD12 Front...

2 Answers

Bosch classixx 1000 washing machine - stops on spin


Washing machine stops at the spin cycle - light flashes. Have to drain water out manually. Happened last week and was then able to run an empty rinse cycle. Machine worked normally for another week. Same problem today but have had to drain water manually from the drum after trying an empty 90 wash and rinse cycle (both stopped on the Spin and flashed). Any ideas? Thanks. x

Apr 29, 2008 | Bosch Classixx WVF 240S Front Load Washer...

1 Answer

Ariston 6kg washing machine


Do you have the "easy iron" feature on? If so, the clothes will stay in water until you manually rinse it.

Oct 07, 2007 | Ariston Technologies AWD 121

2 Answers

MACHINE DOESN'T CYCLE OUT OF RINSE


Does it spin if you move the timer manually? ist it being used on a delicate cycle@? if so it will stop in the last rinse water

Jul 10, 2007 | Ariston Technologies AWD 121

Not finding what you are looking for?
Ariston Technologies AWD121WH Logo

523 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ariston Technologies Washing Machines Experts

Gerry Harvey
Gerry Harvey

Level 3 Expert

1456 Answers

yadayada
yadayada

Level 3 Expert

61037 Answers

Dan Webster
Dan Webster

Level 3 Expert

8147 Answers

Are you an Ariston Technologies Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...