Question about Hobart SR24-H Built-in Dishwasher

2 Answers

Heat tempeture rinsing cicle is on 140 degres how do I bring it up to 170 degres, where can i get a repair service around my area Hartford, Connecticut

Posted by on

Ad

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 704 Answers

There are internal settings that need to be adjusted and programmed by an authorized service tech, since the Health Code requires a minimum wash and rinse temps for proper cleaning and sanitizing of the dishes, etc. This isn't something that can easily be done by just anyone and will require some technical knowledge of this unit.

You can find a Hobart commercial appliance service tech by searching your local yellow pages, under Commercial Appliance or Restrarant Equipment/Service, etc.

Here's a couple to start with in Hartford, CT

Marc's Commercial Appliance Repair - (860) 416-8103
Hartford, CT 06103

A-Able Service Co. - (860) 665-1499
Hartford, CT 06103

There are several others in the area, as Hobart is very popular with commercial kitchens throughout the region.

Hope you find this Very Helpful - Best regards!

Posted on Aug 19, 2009

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 640 Answers

What is the model?

Posted on Feb 08, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Repairman can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Repairman (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Heat tempreture in Phaser 3200 MFP Fusing part


This option does not need to be changed unless you are getting a overheat error. If you lower the heat on the fuser this can result in image transfer on the paper leaving blotches and ruining the fuser.

Jan 22, 2014 | Xerox Phaser Office Equipment & Supplies

1 Answer

I change thermostat, water pump, housing coolant sensor, but yet when i start driving the tempeture goes up and down and the heat gets kind of cool not all


poor coolant flow water pump? air lock in system? bring to operating temp shut down than open air bleed screws.

Jan 02, 2014 | 1997 Pontiac Sunfire

1 Answer

What's the right weight for a heavy bag?


If you're weighing in the 140-170 lb. you should buy a punching bag weighing around 70-90 lb. if your close to 140 you should buy a 70 etc. if you a big guy weighing over 170 lb. you should get over 100 lb. bag. There is also heavy punching bags suitable for children and the weight around 25-55 lb.

Aug 07, 2012 | Boxing

1 Answer

Cda 497/1 not washing


see this possible causes: Water-heating cycle the cicles compren washing, and rinse, the machine stop, because the heating element, and thermostat can be defective test.see the diagram Timer test the timer see the diagram for defective, clean contact, with special spray, tigh the wires very well. 5_9_2012_10_57_35_am.gif5_9_2012_10_57_57_am.gif

May 08, 2012 | Dishwashers

1 Answer

When I turn on my Jackson Delta 5 it says that it is heating water, and that is all it will do. It will set like that until I disconnect the thermostat wire and plug it back in. Then it will continue the...


THIS could be your huckleberry! It is item 3 of suspects...
Also note ITEM 7, "heater delay relay"?

Disconnecting and reconnecting MAY be resetting that relay!?

ALSO BE VERY AWARE OF THIS:

BEFORE the heater element can be energized, the rinse
booster heater MUST be initially filled with water. Damage to
the heater element will occur if the element is not submerged
in water!


Here's your thermostat:


Jackson 5930-003-13-65 THERMOSTAT,
120-170 DEGREE "WAS"

thermo-xpxypaj2co3qxlf13c0q1l2g-5-0.jpg Find it here:

Jackson 5930 003 13 65 THERMOSTAT 120 170 DEGREE WAS
$137.11 plus shipping

OR SAVE SOME LOOT AND GO HERE:

eBay: Jackson thermostat 5930-003-06-48 175-195F
Item location: Camano Island, Washington, United States
eBay:
122938835291
$129.50 INCLUDING SHIPPING!
Get your MANUAL here:

http://www.jacksonwws.com/wp-content/uploads/2016/08/Delta-5E-manual.pdf

text: 'TEMP WASH AND RINSE: 120 degrees'
>>> 140 degrees recommended for BOTH (see page 3). <<<

TROUBLESHOOTING on Page 16 and 17!

"Wash temperature not at required reading."

1. Check that white/blue wires are connected.
2. Defective thermometer.
3. Defective thermostat.
4. Rinse heater defective.
5. Defective heater contactor (R2).
6. Incoming inlet water temperature below required minimum. 7. Defective heater delay relay (R4)

See ANOTHER GREAT troubleshooting chart here!

http://kitchen.manualsonline.com/manuals/mfg/jackson/delta_5_d.html?p=21

$50 please... JUST KIDDING
Anthony

Feb 04, 2018 | Jackson Delta 5 Dishwasher

2 Answers

Rinsing cicle is not stoping.Mashine not responding to any baton.How to stop Rinsing cicle and go to normal mode? Thanks Radan


If its is only the rinsing cycle at start up you can go into the menu and turn the rinsing cycle off.
If its the rinsing cycle for the descale, it has to run out of water to finish. Then reprime the machine and it will start to heat again.

Oct 28, 2010 | Gaggia Titanium Espresso Machine

1 Answer

What does a thermometer symbol with up arrow mean on an shx68


Hello Jsg5,

That symbol means that the dishwasher is heating the water, bringing it up to the required temperature to properly sanitize your dishes.

This symbol can appear during the wash and rinse cycles. It is nothing to worry about. Most dishwasher will heat up the wash and rinse water, it's just that Bosch decided to add an indicator, so users would know that any delay in the wash/rinse cycle, is a result of getting the water up to the proper temperature (typically around 140 degrees F)

Even if you've got your hot water heater or hot water supply set to a very low temperature, the dishwasher will use the built-in heating element (the drying element in the bottom of the dishwasher) to heat the water.

Hope you find this Very Helpful and best regards!

Dec 10, 2009 | Bosch Integra 800 SHX68M0xUC Dishwasher

1 Answer

Dishwasher heats but when it starts the rinse and dry cycle the heating delay light comes on and won't proceed to the next cycle


Sounds like the heating element is not working. Usually the hot water temp is OK for the wash cycle (110 to 140 degrees) but the rinse cycle asks for 140 to 160 which requires the heating element. (As does the dry cycle).

Oct 21, 2009 | Dishwashers

1 Answer

Low oil pressur false warning light


replace the faulty oil pressure sending unit.

Apr 23, 2009 | 1992 Cadillac Seville

1 Answer

How can I adjust my boiler ? the water is only at 140 degres


The thermostat may have gone bad on your espresso machine.

Saeco parts and cleaning supplies:

www.CeriniCoffee.com

Apr 19, 2007 | Saeco Classico Espresso Machine

Not finding what you are looking for?
Hobart SR24-H Built-in Dishwasher Logo

Related Topics:

365 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hobart Dishwashers Experts

Jason

Level 2 Expert

211 Answers

yadayada
yadayada

Level 3 Expert

77499 Answers

Garth Jackson

Level 2 Expert

93 Answers

Are you a Hobart Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...