Question about HP 180 Color Copier

1 Answer

HP 170 Color Copier Carriage Belt Replacement

Looking for installation instructions/service manual for replacing the carriage drive belt.

Thanks in advance

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

My carriage belt has broke is there anyone who can repair it, or how can I fix it. H P Copier Model 170

Posted on Oct 05, 2014

6 Suggested Answers

  • 4 Answers

SOURCE: broken carriage belt

Yea they do http://www.everprint.com/online/simdetail.asp?partno=C4557-40049 I think that would fit.

Posted on Aug 03, 2007

713printech
  • 32 Answers

SOURCE: Replacement carriage belt for HP DesignJet 800

The part number is; C7769-60182 runs at around $70.00.
This component needs to be installed by a service technician. You can seriously damage this plotter if you remove the carriage ribbon connectors and do not install them properly. You will fry the pca board (a $1,100 mistake).

Posted on Nov 19, 2008

  • 8 Answers

SOURCE: Replacement carriage belt for HP DesignJet 800 Printer

It is not recommended that the user replace the carriage belt, on any HP printer. Any damage caused by the user, won't be covered by the warranty and will likely result in a completely useless, but very expensive doorstop. Or paperweight..

I do believe your printer has since been discontinued for support, however only an HP Customer Service Representative would be able to confirm that. I would suggest phoning HP for technical support or to at least confirm whether support is available.

Even if your printer is no longer a) under warranty, which I suspect it's not, or b) out of support completely, they may be able to provide you with a list of Authorized Service Providers (ASPs) within your area.

1-800-474-6836

Best Of Luck.

Posted on Dec 15, 2008

  • 4 Answers

SOURCE: Carriage belt replacement for HP 430

http://www.fixyourownprinter.com/forums/inkjet/36780

Fifth post down.

I changed the carriage belt using these instructions.

Hope that helps

Posted on Feb 05, 2009

technohelp
  • 127 Answers

SOURCE: Service Manual

hi

you can go to this website link and you should be able to find what you are requiring:-
http://h10025.www1.hp.com/ewfrf/wc/manualCategory?lc=en&dlc=en&cc=ca&lang=en&softwareitem=oj461en&os=24&product=59270#
hope it helps you if not get back to me and ill find another area

Posted on May 01, 2009

aardvark42
  • 5 Answers

SOURCE: Broken Belt

Find the manufacturer's part number for the part you need.  You can order it from the manufacturer, or check eBay where you may find a better price.  Here's the link to the HP Parts Store, Fax/Copiers/Scanners: http://tinyurl.com/rbuotv

Posted on May 21, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

HP Designjet 800ps 24". How


Instructions are usually supplied with the belt, however if you are looking for the manual, you can find it here!

Jul 05, 2011 | HP DesignJet 800ps InkJet Printer

3 Answers

Need instructions to replace carriage belt for hp designjet 500, specifically how to remove and replace on the carriage assembly


When you order the belt from hp it will come with the instructions, if not email me and I will send it to you.

Jul 12, 2010 | HP DesignJet 500 InkJet Printer

3 Answers

How can I replace the belt for the ink carriage


Here is an HP Support Forum where a user has posted a detailed procedure for the belt replacement.

http://forums11.itrc.hp.com/service/forums/bizsupport/questionanswer.do?threadId=846691

The Service Manual is needed. It's available at:
http://www.hylink.com/PrinterManual.html
Designjet 430, 450, 455C - Service Manual
DesignJet 430, 450C, 455CA - Quick Reference Service Manual

As mentioned, it's a delicate and time consuming operation. I replaced my belt two years ago with little problem. (Be sure to clean the old degraded belt gunk off the drive pully too!)

It's not a job for "Beginners". More like "Intermediate" or "Advanced".

Good Luck!

This is the part I ordered. It was $15
WARNING: THIS IS FOR THE "E-SIZE" MACHINE.
If you have the smaller one, you must research the part number for that.
C4706-60082 icon_greencheck.gif icon_camera.gif
Carriage belt (E-size) - Long/wide belt attached to the carriage 15.00 0.00 15.00 1 15.00
C4706-60082 icon_greencheck.gif
Carriage belt (E-size) - Long/wide belt attached to the carriage

Oct 21, 2009 | HP DesignJet 450c InkJet Printer

2 Answers

Carriage belt replacement


Use the carriage replacement procedure in the service manual. Download here: www.lpscomputer.com/ec/manuals.htm

Aug 10, 2009 | HP DesignJet 500ps (42 in.) InkJet Printer

1 Answer

DesignJet 450C (E-size)


I replaced that belt about a year ago...it took a long time but seemed to go fine. I have a manual "carriage belt installation instructions" its 12 pages long. check out HP website and if you cant find it online, I could scan it for you.

Mike
mjlehto@charter.net

Mar 29, 2009 | HP DesignJet 450c InkJet Printer

1 Answer

Carriage belt replacement for HP 430


http://www.fixyourownprinter.com/forums/inkjet/36780

Fifth post down.

I changed the carriage belt using these instructions.

Hope that helps

Jan 08, 2009 | HP DesignJet 430 InkJet Printer

1 Answer

Replacement carriage belt for HP DesignJet 800 Printer


It is not recommended that the user replace the carriage belt, on any HP printer. Any damage caused by the user, won't be covered by the warranty and will likely result in a completely useless, but very expensive doorstop. Or paperweight..

I do believe your printer has since been discontinued for support, however only an HP Customer Service Representative would be able to confirm that. I would suggest phoning HP for technical support or to at least confirm whether support is available.

Even if your printer is no longer a) under warranty, which I suspect it's not, or b) out of support completely, they may be able to provide you with a list of Authorized Service Providers (ASPs) within your area.

1-800-474-6836

Best Of Luck.

Nov 19, 2008 | HP DesignJet 500ps (42 in.) InkJet Printer

1 Answer

Replacement carriage belt for HP DesignJet 800


The part number is; C7769-60182 runs at around $70.00.
This component needs to be installed by a service technician. You can seriously damage this plotter if you remove the carriage ribbon connectors and do not install them properly. You will fry the pca board (a $1,100 mistake).

Nov 19, 2008 | HP DesignJet 500ps (42 in.) InkJet Printer

1 Answer

Broken carriage belt


Yea they do http://www.everprint.com/online/simdetail.asp?partno=C4557-40049 I think that would fit.

Aug 03, 2007 | HP 270 Copier

Not finding what you are looking for?
HP 180 Color Copier Logo

Related Topics:

244 people viewed this question

Ask a Question

Usually answered in minutes!

Top HP Printers & Copiers Experts

kakima

Level 3 Expert

96627 Answers

k24674

Level 3 Expert

7987 Answers

Brian Sullivan
Brian Sullivan

Level 3 Expert

27725 Answers

Are you a HP Printer and Copier Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...