Question about Kenmore 62602 Electric Dryer

1 Answer

Kenmore Dryer Model 110

Runs but doesn't get hot the dryer is about 14 years old. Could it be the heating element or is it something else?. DRYER HEATED FOR A SHORT TIME THEN STOPS HEATING, CHECKED OPERATING THERMOSTAT 0 OHMS, ONE SET OF WIRES,OTHER READS 5 OHMS.THERMAL FUSE 0 OHMS.HI LIMIT THERMOSTAT 0 OHMS.THERMAL CUT OUT 0 OHMS.HEATING ELEMENT READS 0 OHMS.SHOULD"NT THIS READ ABOUT 9-13? ONE HALF OF ELEMENT HAS A DARK BLACK COLOR LIKE IT GOT HOT OR BURNED.

Posted by on

  • Anonymous Mar 13, 2014

    i have ohmed out every componet all test good whatelse could it be ??

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Kenmore Master
  • 8,147 Answers

If all of the components are reading ok then you need a timer. Touch your 2 leads together. 0 ohms rght. That means you have a complete circuit.If you get the 0 reading then the element must be otay. Bad timer. Take that fancy meater of yours and atttach one of them leads to the timer leg marked RH. Yank the wire off the terminal beore you test. Move the timer around. You should get the famous 0 reading along the way. If you don't then that means you have the bad timer.

Posted on Feb 05, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Does Not Shut Off


1st go the the house breaker (dbl breaker) for the dryer and shut it off and turn it back on, your dryer runs on 220 volts of power but if the breaker is partially tripped it may be only running on 110 volts which is only enough power to turn the lights on and to turn the drum the element needs 220 volts to turn on. If it still doesn't heat after resetting the breaker then you may need a heating element or thermostat. The dryer isn't shutting off because it isn't detecting the clothes are getting dry so once you fix your heating problem the dryer should start shutting off on its own again.

Apr 21, 2012 | Roper Dryers

1 Answer

29'' Kenmore electric dryer series 110 not heating up


Check the following to address this issue.(Most common issue will be a burned out thermal fuse.)




1. No power to the dryer
Make sure there's power getting to the dryer. Check for tripped circuit breakers or blown fuses. An electric dryer uses two circuit breakers or fuses, and if only one of two is tripped or blown, the dryer might still run but not heat. Sometimes the power cord disconnects or burns at the dryer, if this is the case, the wiring and the terminal block must be repaired or replaced.

2. Heating element
A burned out heating element will show no continuity when measured with a meter. Replace the element if found defective.

3. Thermal fuse
Most dryers have a thermal fuse, which burns out when the dryer overheats, in which case the dryer will either not run at all or stop heating. The fuse is usually located on the vent duct, inside the dryer. A blown fuse will show no continuity when measured with a meter. Before replacing the fuse, make sure the blower wheel is not broken or clogged, and there is nothing blocking the venting.

Aug 03, 2009 | Dryers

2 Answers

Dryer wil not spin


Hope this info helps, ps don't forget to give me a rating thanks!!


For an electric dryer that runs but doesn’t heat, follow this repair roadmap:
Flip the circuit breaker off and then back on. Electric dryers run on a two-pole, 240v breaker. A common problem is for one of the legs to break which cuts the 240v that the elements need to heat up but it still supplies the 120v for the motor. The result is that the dryer runs but doesn’t heat.
If the breaker checks out, then it’s time to do some surgery. Unplug the dryer and open it up.
. Use your ohm meter to test the thermostats. All should show continuity.
Measure the resistance of the heating element with your ohm meter. Normal readings are in the neighborhood of 30 ohms.
In rare cases, the centrifugal switch in the motor can fail which breaks the power circuit for the heating elements. If this is the case, then the entire motor must be replaced since the centrifugal switch is built into the motor.

May 08, 2009 | Dryers

1 Answer

Dryer not hot


Tht means that the element is not heating on.

You need to call a technician to test the element, the thermic sensor, and the control assembly.

The most likely is a defective heating element, that must be replaced.

Jan 31, 2009 | Kenmore 73952 Gas Dryer

1 Answer

Dryer heating element


usually if it heats up but long dry times ,,air flow problem inspect exhaust hose and vent s should resolve problems...

Dec 27, 2008 | Kenmore 62602 Electric Dryer

2 Answers

Kenmore 80 series runs but dont blow hot air


Where is the location of the heating element for a Kenmore 80 series dryer heavy duty model # 77834795

Dec 09, 2008 | Kenmore 63942 Dryer

1 Answer

Kenmore Dryer Model 110


Using a multi-meter, check to be sure that you have 220 volts at the back of the dryer. If you do, unplug the dryer, take the back off and ohm out the t-stats, thermal cut-outs and element.If you can't pinpoint it to one of these then it will be in the controls or maybe the motor start switch.

ps, The dryer motor will run on 110 volts.

Dec 12, 2007 | Dryers

1 Answer

Dryer heating element


NEED More info ...Need model # and type dryer... info u gave is misleading

Oct 09, 2007 | Kenmore 63942 Dryer

Not finding what you are looking for?
Kenmore 62602 Electric Dryer Logo

Related Topics:

376 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kenmore Dryers Experts

Dan Webster
Dan Webster

Level 3 Expert

8147 Answers

Tim Whalen

Level 3 Expert

3056 Answers

Richard Roth
Richard Roth

Level 3 Expert

9472 Answers

Are you a Kenmore Dryer Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...