Question about InFocus LP 600 Multimedia Projector

2 Answers

LP600 - Lamp Did Not Strike

Lamp will not strike in LP600. Receive message "Powering up...Wait..." then "Retrying". Eventually, a message is displayed "Lamp Did Not Strike". The cycle just repeats over and over again... Lamp does power on for a few seconds, but it seems that it does not reach temp and powers off... I am thinking power supply issue...??

Steps already taken:
Replaced lamp.
Visually inspected power supply board.
Checked all connections.

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I have an lp600 it powers on for 5 of the 7 seconds then stops at 2 fans on just wont strike on keep doing the same process

Posted on Aug 21, 2011

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 12 Answers

Check for shorted flat pack diode in power supply.

Posted on Feb 05, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

4 Answers

HI I WANT SERVICE CODE OF INFOCUS LP600 ASKC175


I am not exactly sure what service code you are searching for, what is happening with the projector? You turn it on and immediately it's looking for a code? Please let me know and I can help

Tim

Sep 13, 2010 | IBM Office Equipment & Supplies

1 Answer

ASK Proxima C180 Message saying :Lamp Didn't Strike"," Retrying" What can I do to fix this problem


if you know your lamp is good, make sure the connection on the lamp housing and the connector on the lamp itself are actually connected. sometimes when the lamp is installed the connection on the lamp housing is pushed out and the connection is not actually made. you can also reset the lamp hours and see if that works.

Apr 28, 2010 | ASK Proxima C180 Multimedia Projector

2 Answers

Lp600 won't strike


If you replace the lamp but do not reset the lamp hours then the projector will not ignite the lamp to stop it blowing up the lamp and causing further problems. You can reset the hours without the image, on the x2 version you turned on for 1 minute then held down the volume up and down buttons for 10 seconds but all versions vary. The infocus website can usually tell you how though you may have to look for it a bit. Failing that try a firmware update available from the infocus website that should erase its brain so you can start again, hopefully you have kept the original leads it was shipped with to do this otherwise it will cost you another £20

Feb 11, 2010 | Office Equipment & Supplies

1 Answer

Infocus lp 540


Also having this problem."Warming up" then "lamp didn't strike" then "retrying" stuck in a loop. It's at a school where I work and nobody has reported any messages regarding the lamp hours.

Jul 20, 2008 | InFocus LP 600 Multimedia Projector

1 Answer

Infocus LP120 Retrying-Power Light Turns Red...


Usually when the lamp is good and you get this message, the ballast is bad. That is the part thatdrives the lamp. Check with Infocus for a repalacement balast.
Dan

Apr 09, 2008 | InFocus LP120 / 1000 Lumens / XGA / DLP...

3 Answers

Lamp will not strike error message


this can sometimes indicate either an overheating issue, a lamp service life problem, or that the cover to the lamp housing has not been secured properly.

Dec 14, 2007 | InFocus LP120 / 1000 Lumens / XGA / DLP...

1 Answer

Yo


I believe that does mean the lamp is dead. If your model is the LP600, you need the SP-LAMP-019. A quick search on eBay found one for $320 new. From the InFocus website it is $499 so that is not a bad deal. InFocus offers a 6 month warranty, so that is something you will want to keep in mind.

Sep 16, 2007 | InFocus LP 600 Multimedia Projector

1 Answer

Please help


I believe that does mean the lamp is dead. If your model is the LP600, you need the SP-LAMP-019. A quick search on eBay found one for $320 new. From the InFocus website it is $499 so that is not a bad deal. InFocus offers a 6 month warranty, so that is something you will want to keep in mind.

Sep 16, 2007 | InFocus LP 600 Multimedia Projector

Not finding what you are looking for?
InFocus LP 600 Multimedia Projector Logo

Related Topics:

1,965 people viewed this question

Ask a Question

Usually answered in minutes!

Top InFocus Office Equipment & Supplies Experts

Juan Carlos Pacheco

Level 1 Expert

36 Answers

Electro Med Services...
Electro Med Services...

Level 3 Expert

6694 Answers

color wheel light...
color wheel light...

Level 2 Expert

137 Answers

Are you an InFocus Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...