Question about Marantz SA-1 CD Player

1 Answer

The SA-1 cannot read CD and Display is off

After a few song play the display on again

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Master:

    An expert who has achieved Level 3.

  • Master
  • 848 Answers

Hi,

lens is dirty ........clean the lens using the lens disk cleaner...........still problem continues the laser head is not picking up the disc...........need to replace laser assembly.......

Posted on Feb 04, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Will only play first song and then repeats that song over & over


On your remote control, disengage the "repeat" play button. Normally its under the "play" button control, but make sure the "display window" of the player does indicate change settings.

Oct 17, 2013 | Sony MegaStorage CDP-CX355 300-Disc CD...

1 Answer

Denon CD deck


This unit needs a service visit. It may be a common problem with that model but to me it sound like a power supply issue as when you play a disc more power is used to rotate motors and move the sled. This is indicating to you that it is in a weakened condition and will soon fail more significantly. The problem may be as little as a solder joint or a defective Filter capacitor which is common in some models of equipment.

Dec 11, 2012 | CD Players

1 Answer

Where is the button/knob set up to play single song verses continuos songs from a cd on Pioneer cdj mk..


The button you need is the Auto Cue button, which is to the left of the top display. Press and hold to turn auto cue off, which puts the player into continuous mode. This button is also the Time Mode button.

Hope this helps

Jaye

Sep 17, 2011 | Pioneer CDJ-1000 CD Player

2 Answers

Wurlitzer omt K99 the cd will stop during play


I seem to be having the same problem and all signs point to the serial control board board Pt# 0046630 under the player. The symptoms with mine were randomly cutting off songs about 20 sec after song start and returning disc to carrier. It started mostly when juke was first turned on (cold) and then progressed to all the time and now display on cd board is dark only randomly coming to life then dead again. power on the sub transformer is good and when it comes to life player works well. I am sending the board to be repaired.

Feb 07, 2010 | Wurlitzer Jukebox 1015 One More Time...

2 Answers

Song Programming


Hello,

With regards to your problem with the Rowe Ami 100 cd jukebox.
Do you have a manual, if not I suggest you buy a printer manual or one on CD and refer to the Programming and Installation section.

In order for the jukebox to know about the cd's that are installed in the jukebox it has to initialize all or the changed cd's that have been replaced within the jukebox.

Put the jukebox into the Service Mode (the service mode should appear on the display)
Type 3 to select the Initialize sub menu
Type 0 and full initialize will appear on the display
Press Popular to start the initialization
Place the jukebox service switch into the normal mode

Initiazation will take around 30 minutes to complete.

Regards
Alan Hood
ami-man

Jan 05, 2009 | Wurlitzer Jukebox CD Player

3 Answers

Technics sl-pg580A


this player uses a philips mechanism, spindle motor failure is very common on these mechanisms, yours may be on its way out. take the lid off and insert a cd and if you can hear the laser trying to read the cd without it spinning, it's definately the spindle motor.

Oct 07, 2008 | Technics SL-PG480A CD Player

1 Answer

Numark Cd-Mix-2 left side disk problem


Cd drawer and laser assembly are belt driven. Belt needs to be replaced

Sep 08, 2008 | Nu Mark Numark Cd-Mix-2 Dual CD...

2 Answers

Wurlitzer 1015 OMT Disc spins, then stops....


Spoke with "Doctor Jukebox" from Folsom, CA about a similar problem I had. You can find him on craigslist.

I did NOT have the "2222" display issue.

Root cause: The laser isn't "seeing" the CD and interprets inability to see as being the end of the track, therefore, puts the CD back into the carousel.

Solutions:

1) Clean the lens. Be careful to use an appropriate lens cleaning solution. The lens is made of plastic and may cloud up if a harsh solution is used. Use a Q-tip dipped into the cleaning solution and gently clean the lens using a side-to-side motion, not a front-to-back motion. Wait for a bit until the lens is completely dry, then try playing a CD. (note: this fixed the problem for me)

If that doesn't work...

2) Replace the laser module. It's easy to remove with a torx. Be gentle when disconnecting and reconnecting the ribbon cable and/or other connections so you don't bend the leads. Laser modules cost a few hundred dollars, so try Solution 1) above before replacing the module.

Mar 15, 2008 | Wurlitzer Jukebox 1015 One More Time...

1 Answer

CD player won't play random


the most likely problem is a weak or failing optical pickup. try a cleaning disc first there may be dust on the lens. do not use any liquid to clean the lens. remember this is an optical system if it can't focus properly or "see well" it can't read.

Feb 03, 2008 | CD Players

1 Answer

CD PLayer no longer recognising CD RW discs


use fine cd on ur player. If some cd is not working ten do not try it again an again. Try different one. Thank You.

Aug 12, 2007 | Teac PD-H300 CD Player

Not finding what you are looking for?
Marantz SA-1 CD Player Logo

Related Topics:

306 people viewed this question

Ask a Question

Usually answered in minutes!

Top Marantz CD Players Experts

xxxxxx xxx

Level 3 Expert

4706 Answers

The Knight
The Knight

Level 3 Expert

68157 Answers

yadayada
yadayada

Level 3 Expert

60667 Answers

Are you a Marantz CD Player Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...