Question about Daewoo DTQ-1440FC 13" TV

1 Answer

Help my tv is stuck on line.what do i do?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 8 Answers

This s gizmofreak
the solution to the above problem
once again reset ur tv set, and check the cables are connected properly and this s because of mainly eht n ur tv it wont go to its original state as soon so it take some time to reset then proceed it will work

please do me the rating

Posted on Feb 04, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a grundig model no gulenar26hdib that is stuck in standby, i have took the back cover off, all caps look ok and there is a slight hissing noise every five or six seconds, can anybody tell me what...


It sounds that the LOT [Line Output Transistor or Line output transformere] to your TV is faulty.

Visit this site for more details. Type in the site name Electro-help either to Google or Yahoo search box [not in the address bar of your browser], and click search. It is an electronic equipments service help site. All details you want are there. Note the position of hyphen in between words in site name, when you type it in. The site will appear as it is in web; subtitled as electronics equipments' repair help.
Picture of line output transformer is given. It may look different from this picture, but remble most.

5_18_2012_2_07_02_am.jpgThis is the picture of Line Output Transistor.5_18_2012_2_08_02_am.jpg

May 17, 2012 | Grundig GF70-600 TV

1 Answer

My rca tv is stuck on channel 3


Your TV at one time may have had a converter or satellite box. In that case, channel 3 is all you would need. On the other hand, if you want to connect to standard cable TV (no box), do so. Then you will need to get in the menu and press auto search. This will give you the old standard channel line up. Thanks for asking!

Oct 16, 2011 | RCA F27442 27" TV

1 Answer

Have Aiwa TV MODEL No. TV-A209 The problem that I am suddenly facing is that I can't change channels or volume or use any other function. I can't even turn it off with remote control. Its stuck...


have Aiwa TV MODEL No. TV-A209
The problem that I am suddenly facing is that I can't change channels or volume or use any other function. I can't even turn it off with remote control.

Its stuck randomly on a particular channel that I was watching at that point of time.

Along with that channel it now shows a message in flashing red color that reads :-
AGING
O6895H

Now when I press ''Display'' button on remote control volume goes off and this code is shown :-
S123 K234 Y
000 001 1


The numbers in the second line can be navigated by ''CH+'' button and changed between 0 and 1 by ''Vol+'' button.

I really don't know anything about this. So, please help me out of this problem.

Nov 08, 2010 | Standard (CRT) Televisions

1 Answer

My tv is stuck on channel 2


Our old tv is stuck on Channel 2 and will only change ot aux. Help!

May 16, 2010 | Standard (CRT) Televisions

3 Answers

When i turn the tv. on, the volume line appears all the way to zero. if i turn the volume up, it goes up but when i release the up button the volume goes down all by itself.


It sounds like one of the volume down buttons is stuck in the activate position. The same as if you were holding the down volume button continuously. It could be either the volume down button on the TV or the remote. I would try remove the batteries of the remote then adjust the volume by the TV buttons.


If the volume doesn't go back down then the remote is the problem. In order to fix the remote you may need to take it apart. This is normally easy to do just locate any screws that may be holding the remote together. If you don't see any screws then you will need to pry the two sections apart. Separate the circuit board and rubber buttons and clean them both with some rubbing alcohol and reassemble it. If it still has the volume issue you may need to replace it.

If the problem persists with the remote deactivated then it's the volume button located on the TV. That is a little more difficult. You can try wiggling the button or some canned air (used to clean computer keyboards) to blow it clean. However it may need to be disassembled to gain access to the switches for proper cleaning.
Hope this helps.

Oct 19, 2009 | Toshiba 32A33 32" TV

5 Answers

Aiwa TV MODEL No. TV-A149 AGING


I have Aiwa TV MODEL No. TV-A149
The problem that I am suddenly facing is that I can't change channels or volume or use any other function. I can't even turn it off with remote control.

Its stuck randomly on a particular channel that I was watching at that point of time.

Along with that channel it now shows a message in flashing red color that reads :-
AGING
6EDEH

Now when I press ''Display'' button on remote control volume goes off and this code is shown :-
S123 K234 Y
100 000 0


The numbers in the second line can be navigated by ''CH+'' button and changed between 0 and 1 by ''Vol+'' button.

I really don't know anything about this. So, please help me out of this problem.

Sep 14, 2009 | Aiwa TV-S2011 20"

1 Answer

Volume


The tv has a static sound and picture has vertical lines but is still visible. Heeeeeeelllllp. Thank you.

Jul 21, 2008 | Philips 19PR19 19" TV

1 Answer

Haier TN201AUV 20"


The GE Universal Remote will do the job. I have on and it works for my Haier TN201AUV TV. You can also find a replacement Haier remote on Remote Hound's web site.

On the other side of this I have a Dish Network remote that WILL NOT work. The Dish Network remote does not list any codes for Haier. Dish Network Tech Support could offer no help.

In an attempt to solve the problem myself, I looked on-line at GE's site listing all of the manufacturers' for their remotes and found the identical code that worked for my Haier TV also listed under APEX TV's. The Dish Remote lists (11) APEX TV codes. Ironically, NONE OF THEM WORK!

I'm stuck with using both remotes... and that's BULL$H!T

Dec 01, 2007 | Haier HTF20R21 20" TV

1 Answer

Can't Change Inputs on TV


make sure that your remote is on the tv cotrle mode rather than the dvd control mode

Nov 10, 2007 | Mintek DTV-323-D TV

Not finding what you are looking for?
Standard (CRT) Televisions Logo

Related Topics:

50 people viewed this question

Ask a Question

Usually answered in minutes!

Top Daewoo Standard (CRT) Televisions Experts

The Knight
The Knight

Level 3 Expert

68229 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Electro Med Services...
Electro Med Services...

Level 3 Expert

5612 Answers

Are you a Daewoo Standard (CRT) Television Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...