Question about Crosman (4032)

1 Answer

Play in the barrel

Bought brand new 760, got it home and noticed play in the barrel. It is very accurate when lined up correctly. Take it back or is there an easy fix?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 18 Answers

You can send it in to crosman with $14 and they will send you a used gun. Yes, they are used but at least they still work.

Posted on Feb 17, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I had my Crosman 357 for about 15 years or so. I never used it at all until a couple weeks ago and it worked great for a few days and I liked it so much I bought more "clips", ammo and CO2 for it and then...


Well I recently bought a crosman like a month ago, I worked great, I also use CO2, then i started using it again, and all of a sudden all of the CO2 started seeping out of the barrel and CO2 area, cartridge after cartridge, so i said screw it and took it apart, and found the area that deals with the CO2 and tightened everything up. I couldn't put it back together, so i looked for the schematics and finally got it back together, then i tested it out and it works fine now. Good luck.

Oct 25, 2010 | Crosman Spotting Scopes

1 Answer

I bought a used scope with no manual. On the front of the scope it turns like the back but it has ranges on it do I need to know what range I am shooting for the rifle to be accurite


Take the bolt out of the rifle so you can sight down the barrel to the target. Get the target bullseye in the center of the barrel. Now look through the scope to see where it is. Adjust the windage and elevation screws to get the cross hairs on the bullseye. Look through the barrel several times to make sure the gun did not move off the target during the adjustments. A concrete bench with sandbags is best to use for this.

Dec 05, 2009 | Burris Fullfield II Riflescope

1 Answer

397 Ben/Sher .177 air rifle - installing repair kit problem


Crosman bought out benjamin / sheridan, and they still repair just all their pump guns. The ring sounds like a piece of a pellet, the barrels are silver soldered to the bottom tube, Not lead. Also, the repair kit should not have too many parts, you can only go so far with those guns before needing special equipment to get them apart. Get a hold of Crosman and tell them that benjamin sent you a bad part. They should fix it.
I had an old Benjamin Franklin in .22 cal, it was just a brass tube with a stock and barrel. I sent it to them, to be repaired, and I wanted the .22, because I had the 5mm and the 177. So I got it back, cost $29, New barrel, in .177, soldered on, new guts, new paint, trigger, bolt, the works.. Brand new gun. I told them I wanted the brass and I wanted the .22, They said oops, sorry. I didn't complain, nice old gun. Hope this helps.

Jul 29, 2009 | Crosman (4032)

6 Answers

Crosman Powermaster 760 pump bb gun won't hold an air charge


Take a look on amazon Amazon com Crosman Powermaster 760 pump and take a look for replacement. have a nice day

Feb 12, 2009 | Crosman (4032)

2 Answers

Powermaster 760 b-b repeater/177 pell. gun.


go to www.crosman.com and they have a parts list that should help in getting the parts needed for replacement.

Oct 01, 2008 | Crosman (4032)

2 Answers

Crosman 2104 Air Rifle


i had the same problem with my 2100. you would have to take it apart. the barrel is held in place with a small allen bolt. you would remove the bolt and slap some locktight on it and retighten.  that should solve your problem but i would think twice before taking it apart cuz its kind of tricky getting it back together and I would replace any seals while you have it apart. good luck

Jul 25, 2008 | Crosman (4032)

3 Answers

Crossman 760


crosmanpumpmaster760assembly.jpg
picture of pumpmaster 760 trigger assembly

Jul 07, 2008 | Crosman (4032)

3 Answers

I need to reassemble a crossman airgun model 760-D


i need a website adress or link to a understandable diagram of how it goes together

Mar 12, 2008 | Crosman (4032)

Not finding what you are looking for?
Crosman (4032) Logo

Related Topics:

105 people viewed this question

Ask a Question

Usually answered in minutes!

Top Crosman Spotting Scopes Experts

Brad Brown

Level 3 Expert

13531 Answers

raysaw

Level 2 Expert

223 Answers

jr3261

Level 1 Expert

42 Answers

Are you a Crosman Spotting Scope Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...