Question about EliteGroup P4VXASD2 Motherboard

1 Answer

On the motherboard p4vxasd2+ i was wondering h where the pw switch, rest switch and hd led go on the pins

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 12 Answers

Hello,
I have provided a link to the manual (requires Adobe Reader to read)
On page 15 it gives you a layout of the pins and tells you exactly what goes where.

Manual Here

Posted on Feb 03, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where connect LED,RESET etc wires are attached


Please refer to the following list of the PANEL1 pin assignments.
Pin Signal Pin Signal
1 HD_LED_P(+) 2 FP PWR/SLP(+)
3 HD_LED_N(-) 4 FP PWR/SLP(-)
5 RESET_SW_N(-) 6 POWER_SW_P(+)
7 RESET_SW_P(+) 8 POWER_SW_N(-)
9 RSVD_DNU 10 KEY
Pin Signal Pin Signal
1 SPKR 2 NC
3 GND 4 +5V
AUDIO2
1
1
USB3
SPKR1
1
These are all contained in the users manual. If you don't have one go to Mercury website and download it.

Mar 28, 2014 | Mercury Motherboards

1 Answer

Where to fix the power switch,power led and HDD led


There will be a set up pins pointing up from the mother board - usually along one edge, and the cable you have that come from the switches / LEDs on the front panel will fall in the general direction of those pins. If you look very carefully at the writing next to those pins you will see words like PW = power switch, HD LED = Hard Drive LED lights, SP = speaker and so on. You really should visit the motherboard manufactures web site, find your board and download the manual which will show you as well as tell you how to connect up the wires. LET this be a lesson to you! Write down or draw a picture BEFORE you start pulling wires out!

Dec 22, 2013 | HP Vectra VL400 P3 Skt 370 Motherboard...

1 Answer

I do not which pin is for the wire power, reset, HD led, - p ledand positive P led.


E 210882 Motherboard power swicth, rest swicth, HDD led, - P led and positive P led pins

Mar 21, 2010 | Dell (E210882) Motherboard

1 Answer

WHERE TO PLUG IN POWER SWITCH


on the mother board look at the side of the pin of the power switch on the mother board, at the side there is HD LED for hard disk, RESET for the reset, PW for power just the way it is started put it like that.

Mar 03, 2010 | ASUS P5QL-EM - Motherboard - micro ATX -...

1 Answer

Re-reset botton pw- power botton hdd led- hard disk led pw LED- power led idenfification problem help me


from the 1 pin that is single without pair..disregard that then put the pw button.. to make sure short it using a philips or long nose.. if you find the power on button...or just find first the power button by shorting the pins...

the sequnce are pw button reset button pw led hdd led..you just nid to align them to the power button..

hope i've help you..

rate...

Feb 06, 2010 | Zerus Intel Desktop Board D815EEA...

1 Answer

Pins lay out for panel lights indicators


This is EliteGroup Support, and the download page for the Motherboard Manual, for the P4VXASD2 motherboard,

http://www.ecs.com.tw/ECSWebSite/Downloads/ProductsDetail_Download.aspx?detailid=181&DetailName=New&DetailDesc=&CategoryID=1&MenuID=6&LanID=0

Click on the - Manual- tab.
(New, BIOS, Driver, Manual)

Down at the bottom where it states -
English manual for P4VXASD2 PCB v3.3,
click on the country nearest you.

(To the left of Download.
Taiwan, USA, Europe, China)

A small window will come up. This is a Zip file. make sure the empty circle to the left of Save, has a green dot in it.
If not, Left-click once in this empty circle.

You'll see a download progression bar. After it downloads all the way, close this progression bar window. (Click on the Red X)

If you do not have your downloads set to save to your My Documents folder, this Zip file will go to your desktop screen.

In either place, (My Documents, or desktop screen), Double-click right on the file name when you see it.

In the next window go up to the upper left, and click on - Extract All Files

Click on Next, Next, and Finish.

In this small window you are looking at the file in a PDF file form. This is an Adobe PDF icon next to the file name.
Double-click on the file name.

You are now looking at the Motherboard Manual.

Page 8 shows you the Motherboard Components.

Panel 2 is the Front Panel header.

(Connector on motherboard is a Header. The Front Panel, is the plastic panel in front of your computer tower. Has the LED lights, Power On switch, and so on.)

Panel 2 connections are shown on Page 15.

Should you not be able to download this manual, I will detail out the connections for the Panel 2 header.

Orient the motherboard, so we are both looking at it the same way.

Processor is at the Top.
Ram Memory slots are to the Right.
Panel 2 is to the right of the CMOS battery, real close to the outside of the motherboard.
(NOT JBAT 1)
It is right below the IDE 1 header for the Harddrive.

The Panel 2 header is made up of 2 rows.
One down the Left side.
One down the Right side.

The pins in the header are numbered.

Starting at the Top, going down the Left side.
Pins 10, 8, 6, 4, and 2.
There is NO Pin 10. Just a blank spot.

Starting at the Top, going down the Right side.
Pins 9, 7, 5, 3, and 1.

Pin 9 has No Connection

Pins 6 and 8 are for the Power On switch.

Pins 2 and 4 are for the Green LED light.

Pins 1 and 3 are for the Harddrive light.
(Harddrive activity light. Pin 1 is for the + side of the light)

Pins 5 and 7 are for the Reset switch.

Nov 25, 2009 | EliteGroup P4VXASD2 Motherboard

1 Answer

GOT NEW BOARD NEED TO WIER IN FRONT PANEL THE REST IVE DON


You can download the manual from Intel here. Jumpers and header functions are all described there.

Mar 20, 2009 | Asrock K7S41GX Motherboard

1 Answer

Motherboard Pinout - Please Help


here are some sites that may help you.
all these should be marked power switch may say pw,prs,ps, power led may say pld, pl,led, hhd say hd, reset switch maysay rs, set, these connection will be grouped together, and pin layout 1 red or hot wire, or the main wire for the device you are trying to operate.
www.motherboards.org
www.tomshardware.com
www.twinight.org/chipdir/
www.anandtech.com

the connections to the back plate is standard the amount of pins match up the cable, the number 1 pin will be marked some how and or the cable will only be able to plug in one way.
with an exception if you are using serial connector and we hardly use them. the rules are the same as above, and plug ins maybe one way also.

the ribbon type will have a marking on the cable or ribbin line or dots or hasshs marks that is pin #1
match with pin out on motherboard pin1 or pin 0,

rod

Feb 11, 2009 | Syntax SVM266A (SYSVM266A) Motherboard

5 Answers

Gigabyte GA-8INXP Motherboard Problem- front connector pins


If the wires from the reset switch is white/blue the blue wire is positive, Hdd red/white red is positive power Green/white Green is positive etc. The wires on the speaker connector will be red/black/black/white - red is positive. The colored wire is always positive. On all GA mb's the positive connection is always towards the back of the MB and are marked with a + on the base of the pin as you can see on the photo. Hope this help.

Sep 19, 2008 | Gigabyte GA-8INXP Motherboard

Not finding what you are looking for?
EliteGroup P4VXASD2 Motherboard Logo

Related Topics:

385 people viewed this question

Ask a Question

Usually answered in minutes!

Top EliteGroup Motherboards Experts

Brian Sullivan
Brian Sullivan

Level 3 Expert

27725 Answers

Mark Taylor
Mark Taylor

Level 3 Expert

728 Answers

Michael Thomas
Michael Thomas

Level 3 Expert

3051 Answers

Are you an EliteGroup Motherboard Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...