Question about Remington 111409 - 01 6" Branch Wizard Electric Pruning Saw

2 Answers

Ryobi pole saw model ry52502

Need 2 adjust carburetor don't have the tool

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

My Ryobi RY52502 starts but when i change the lever from start to run, it will shut off

Posted on Apr 10, 2011

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 211 Answers

Hi

Try to buy it from a shop.

best regards savumihai71

Posted on Feb 12, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Do you have a better pruner?


Ryobi P4360/P4361 Cordless 18v ONE+ System Pole Saw ...

? 13:42
www.youtube.com/watch?v=PFANQ0JgpZk
Jun 12, 2013 - Uploaded by 8digitPDX The Ryobi 18v Power pruning saw - surprisingly good performance for the money from a ... Ryobi P4360/P4361 Cordless 18v ONE+ System Pole Saw Tree Pruning Saw .... Lithium-ionPole Saw - Unboxing and Review!

Oct 08, 2015 | Chainsaws

1 Answer

Need tool for adjusting air fuel ratio for husqvarna 235 chain saw


It should be a spline tool. It is the most common one.
Genuine Poulan Weedeater Part 530035560 Carb Adjusting Tool

If you work a lot 2 cycle trimmers and chainsaws you might buying the set of four adjustment tools.
2 Cycle Carburetor Adjustment Kit Includes 530035560

Nov 07, 2014 | Husqvarna Chainsaws

1 Answer

Ryobi t-30 pole saw runs high rpm with choke on


Sucking air in somewhere. Need to check carburetor and gaskets to identify where leak is.

Oct 10, 2014 | Chainsaws

1 Answer

I need the Primer Blub for a model 106890-02 Remington Electric Pole Saw


It must have a ZAMA or Walbro carburetor on it. Look at the shiny chrome piece on the carb. Then buy the Bulb for that brand of carburetor

Sep 30, 2013 | Remington Electric Pole Saw

1 Answer

I have a RYOBI pole saw that starts fine, but there is a disconnect between engine and saw blade. The blade will not turn.


I assume you have the Ryobi powerhead with the multiple tool shaft (can use it with an edger, blower, trimmer, and pole saw) If so, does the powerhead square drive spin when you squeeze the throttle trigger? Does the chain move freely on the saw end when not connected? Is the attachment fully inserted into the powerhead shaft (small spring-loaded button should pop out of the hole when fully inserted.

Aug 26, 2011 | Chainsaws

1 Answer

Carnt keep ryobi pcn 4545 running when i increse the power


How do you increase the power to an electric saw? By your question, I'm assuming a fueled engine model. Check the fuel filter, air filter, and muffler for any plugging. Check condition of fuel lines and tightness of carburetor fasteners. If no help, turn the H jet needle CCW about 1/4 turn--which should result in the engine 4-stroking. Will the engine now run at speed (but not as fast as before)? If ok, warm the engine up, open the throttle and adjust H CW until the engine speeds up somewhat, but still 4-stroking. Proper adjustment is when the engine 4-strokes, but immediately 2-strokes when cutting. This produces best power and least heat! Hope this helps!

Apr 26, 2010 | Ryobi 18-inch Electric Chainsaw Chain Saws

1 Answer

I need an Idle Speed Adjustment Screw for a Poulan ProPP4218 Chain Saw.


Ordertree.com (Poulan authorized parts outlet)
http://www.ordertree.com/cms/contact-us/9790.html
Telephone - For Handheld or Wheeled Products contact us at 1-877-500-7499
I looked at "Gas Chain Saw PP4218 Types 1 & 2" IPLs. there are no carburetor illustrations. I suggest you contact them by phone. Please have your saw and a supply of common hand tools within easy reach before calling. HTH
Lou
There are often multiple carburetor manufacturer's used on the same model. They can easily help you determine what is on your saw.

Dec 14, 2009 | Poulan Pro 42CC 2 Cycle Chainsaw, 18"

1 Answer

What is the walbro chain saw carburetor adjustment for a


There is no set adjustment on any chain saw. If it were that simple there would be no need for adjustments. The problem is that most equipment manufactured in the past 10 years can not be adjusted by the user. Carburetors are now equipped with either adjustment limiters which limit the adjustment to less than half a turn or with adjustment screws that require a special tool to make the adjustment. More than likely you will have to take it to an authorized dealer for those adjustments.

If you do have an adjustable carburetor, then gently close both needles and open each on 1 full turn. This should allow the engine to start and the final adjustments can be made at that point. If it still will not start then open each needle 1/8 to 1/4 turn and try again. If this still does not work then most likely your carburetor needs a good cleaning and a rebuild kit.

Sep 13, 2009 | Poulan Chainsaws

1 Answer

Engine will not run when chock is not on


Hi

Try this link to find out where the carb adjusment screws are http://wssemw.arinet.com/scripts/EmpartISAPI.dll?MF&app=EWSS&session=401c0624-691d-43f6-9249-845e18527269&cat=3&TF=epcFrame&assem=452&highlightNode=No&selAssem=4447&mdDescrip=PP258TP Pole Pruner.

best regards savumihai71

Dec 17, 2008 | Chainsaws

Not finding what you are looking for?
Remington 111409 - 01 6" Branch Wizard Electric Pruning Saw Logo

1,013 people viewed this question

Ask a Question

Usually answered in minutes!

Top Remington Chainsaws Experts

Roland W VanLue
Roland W VanLue

Level 3 Expert

375 Answers

EugenesDIYDen
EugenesDIYDen

Level 3 Expert

479 Answers

Phil Walker
Phil Walker

Level 3 Expert

602 Answers

Are you a Remington Chainsaw Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...