Question about PC Desktops

1 Answer

Jumpers Hi , I have a GA-8s661fxm motherboard and it has no jumpers on it at all. I can't use it . I'm looking fr a manual or something that will show what jumpers go where. I was wondering if you can help me. The board probably doesn't work , but I want to find out. Any help I would be thankful for. Thank You .

Posted by on

  • jhiltz1 Feb 05, 2009

    thanks for your help. I'll try that. Also can you tell me what a long beep means when I start up my puter and nothing happens? It's a puter that I'm fixing for a friend. I checked the Bios codes, but none listed for just one l o n g beep that repeats itself. I would be grateful if you can help with this one. later. And thanks.

  • jhiltz1 Feb 05, 2009

    I go to this site and click on the manual that I want , but I only get a blank page. but thanks for your help earlier.

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sniper:

    An expert who has posted more than 50 answers, of which 90% or more were rated as helpful.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

  • Expert
  • 86 Answers

You can download a manual for that motherboard from the Gigabyte site:
http://www.gigabyte.com.tw/Support/Motherboard/Manual_Model.aspx?ProductID=1724

Posted on Feb 05, 2009

  • Dwayne Bowers Feb 06, 2009

    I had no trouble using the "Europe" link to download and view the pdf file. It did seem to stall on the other links.

  • Dwayne Bowers Feb 06, 2009

    In the Award BIOS, one long beep usually denotes a memory problem of some sort. Ensure the RAM is seated and in the correct slots. If you have some matching RAM lying around that is known to be good, try it in your machine.

×

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Power on password


Hi,

What are you looking to do with the power on password?

You can typically reset it by pulling a jumper on the motherboard. I've attached the user manual for your system below, consult it to locate this jumper:

HP Compaq 6005 Pro Series QuickSpecs c04123349 pdf

Hope this helps!

Feb 20, 2015 | HP Compaq 6005 Pro SK557UC Small Form...

1 Answer

Bios admin. lockout


Find the bios reset jumper on the motherboard and short the two pins for a few seconds with either a jumper or a small screwdriver. Do this with the main power cord disconnected. This will reset everything to the motherboard maker's default settings. Open the case and find the model number of the mo-bo. (or download and install CPU-Z, which will show all your hardware details) Then Google the model to get the manual that shows where the bios jumper is located.
An easier solution is to go back to where it was stolen from and ask the rightful owner what the password is.

May 06, 2012 | Dell Precision Workstation 470 (204816690)...

1 Answer

Mobo Jumper settings for BX pro PC100 Motherboard


*********** board sounds like the same as a Fujitsu board.
D1115
moz-screenshot-1.pngthe user manual can be found at diplodocs
It shows the jumper settings and board layout for a Fujitsu motherboard.
I hope this helps. Have a great day

Mar 18, 2010 | PC Desktops

2 Answers

GA-81915PMD


most of that is done through the bios now,if its old, goto th manufacturers website and click on downloads, enter the model of the board, and download the manual, please give a fixya rating if this helps, thanks

Jul 10, 2009 | Gateway 830GM PC Desktop

1 Answer

When power it on nothing comes up. in front has light 1-4 and only 1 and 2 light up. I have had this problem with other when I plugged in to many usb connections and dell had me reset something on the...


Hi there.
They probably had you clear the CMOS jumper or take the motherboard battery out.
The CMOS jumper looks like this >>>>
82daf9c.jpg
It is the little piece of plastic next to the motherboard battery, if its there move the jumper to the other (on) position for 5 seconds.
If there is not a jumper there take the motherboard battery out for an hour making sure the power cord is removed from the back of the machine.
Please post back if you need anymore advice.

Good luck

Jun 04, 2009 | Dell OptiPlex GX620 PC Desktop

1 Answer

I recently upraded my computer with an Asrock Penryn1600SLI-110dB motherboard with an Intel CORE 2 DUO E4600 processor. The symptoms are: When I tried to boot for the first time the cpu and case...


Hi,

If you have recently upgraded your motherboard and when you turn it on, there is no display. You could check the jumper setting of your motherboard.

http://download.asrock.com/manual/PENRYN1600SLI-110DB.pdf

Check this site for jumper settings. Download the manual. Go first to page 11 and find clear CMOS jumper. That will be number 17. Then go to page 24 for the correct jumper settings. Jumper should be on the pins 1 and 2. That's the default settings.

If the jumper is set already to 1 and 2. Clear the CMOS by putting the jumper on 2 and 3. It should be off when you are going to set the jumper. This is to make sure that the settings for your motherboard is set to its original settings.

If you are going to clear the CMOS settings, you will have turn the computer on after clearing it and then turn it off again. Put the jumper back to pins 1 and 2. Now make sure that computer is totally off. Uplugged the computer just to make sure when you are doing this.

Note:
To test also the motherboard if it is working, do not connect the other pheriperals such as network card, sound card, and other cards that is not buit-in. Also drives such as Hard Drive and CDROM drives.

Check for beep codes. Short beeps tells you that the Video card is not inserted properly. Long beeps tells you that the memory card is not in place correctly.

Just remove the Video card or Memory card and then place it back again.

Computer should be off as well when doing this.




Sep 09, 2008 | PC Desktops

1 Answer

I have motherboard GA-8S661FXM-775, my BIOS OEM is 8S661FXM-775 F2c-F2c, installed in my computer SEANIX-8A1DAAE5, I upgraded my BIOS to 8S661FXM-775 F4, and the result is slowdown and freezing computer,...


if you backed up your old Bios replace it with the one you upgraded. if not download the correct Bios again and upgrade a second time,

remember that after you upgrade the bios you have to go into the bios settings and select something like "apply basic setting" or a similar statement, exit and reboot.

good luck & please rate my efforts
Terry

Apr 03, 2008 | PC Desktops

2 Answers

Re:Bios jumper


Your computer is an IBM Netvista 8311.
This link shows ibm netvista 8311 motherboard diagram
www-307.ibm.com/pc/support/site.wss/document....

The cmos reset jumper it is indicated on nr.10, alternatevely when you cannot find reset jumper on a motherboard you can pull out and put back motherboard battery

Best regards

Mar 17, 2008 | IBM NetVista PC Desktop

1 Answer

GA-7VKMLS MOTHERBOARD


You can do it one of two ways:

1. Remove the plug from your computer, then look for the CMOS batter is circular between the size of quarter and a nickel. Remove this and the plug for about 30 secs then put them both back in this should clear it.

2. Most motherboard has a cmos jumper that will clear the bios settings. Check your manual for the exact jumper and setting.

Mar 07, 2008 | PC Desktops

Not finding what you are looking for?
PC Desktops Logo

Related Topics:

67 people viewed this question

Ask a Question

Usually answered in minutes!

Top PC Desktops Experts

joecoolvette
joecoolvette

Level 3 Expert

5660 Answers

Brian Sullivan
Brian Sullivan

Level 3 Expert

27725 Answers

Les Dickinson
Les Dickinson

Level 3 Expert

18299 Answers

Are you a PC Desktop Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...