Hello, and thank you for your time. I am interested in finding out information (such as the year) about the following whirlpool dryer: MOD LER8648LGO SER MM4304164 Type DWSR-ELE-2406028-FM54 119G File E22253

Most dryers are 240v

Hello,

You could go to whirlpool.com and click ower center and download a maual for your washer,i tried that but it says the model number couldn't be matched
The following is from the whirlpool website and it shows where to find the model#


Please find the type of appliance you are interested in and click on the link to view the likely location of the model number plate on that appliance here is where the model# could be found

Type of Appliance Model Number Plate Location Range Inside oven drawer, on oven rim Wall Oven Inside oven drawer, on rim Cooktop On underside of unit Microwave Inside microwave, on rim Dishwasher Inside dishwasher, on rim Refrigerator Inside refrigerator, on wall Trash Compactor Inside, on rim Food Waste Disposer Attached to the unit Washer Beneath washer lid, on tub rim Dryer Inside dryer door, on rim.

Hello,

Most likely this means you have a blocked vent. Check the vent hose behind the dryer followed by the vent in the wall.

http://www.appliancerepairlesson.com/

Hi,

If your dryer is not drying like it once did or if you just have not taken the time to give yourself a clean dryer in a long time then you need to do that. At least once a year the dryer cleaning should take place. Lint build up in the dryer duct is one of the main causes for your dryer to fail.

Here is the rest of this tip about Dryer Maintenance

heatman101

Hi,

If your dryer is not drying like it once did or if you just have not taken the time to give yourself a clean dryer in a long time then you need to do that. At least once a year the dryer cleaning should take place. Lint build up in the dryer duct is one of the main causes for your dryer to fail.

Here is the rest of this tip about Dryer Maintenance

heatman101

The manufacture date is dtermined by the serial number on the appliance. The following link explains how to determine the date code from the serial number on a Whirlpool:

http://www.fixya.com/support/r3576437-determining_the_age_of_your_whirlpool_ap

The second digit represents the YEAR of manufacure. The first two numbers after that represent the WEEK. So...according to the serial number you provide, this dryer was manufactured the first week in May of 1981. That would make your dryer almost 29 years old.

FYI: Even though the dryer is old, many of the parts are still used in modern appliances today, so parts are still available. Whirlpool did not change their parts too much over the years. I found a parts listing for this dryer available at pcappliancerepair.com. I hope you find this information helpful.

The belt can be replaced as follows.
1 remove top and front of dryer shell
2 belt goes around drum around motor pully then under tentioner wheel
3 replace front and top of dryer
(top pops off use a slotted screw driver)
Thanx for using Fixya Please take your time to rate me

Hi,
This could be caused by an internal thermal overload switch. These usually have a limited life span in any appliance that uses heating elements. Try to locate the overload switch which usually looks like a small diode or resistor. You can determine if this is the cause by bridging the switch with a piece of wire, then trying the dryer once more.
Best wishes,
Graemevm

It appears your thermistor or gas valve solenoid has failed in this instance.

For replacement parts - head on over to PartSelect.com or RepairClinic.com and enter in your full model number for a full parts listing.
I recommend both sites because ...


FixYa has no affiliation with either site - I have been using and recommending them for years - trouble free.

PartSelect has a great schematic database for locating the part on your unit and great "testimonials" for each part that often times includes HOW-TO information.
RepairClinic has pictures of each part they sell and also a great how-to and troubleshooting for basic repairs.


If your unit has never been serviced - there should still be an original service manual enclosed in plastic taped to the inside of the shell.
In the service manual are Error codes, maintenance procedures, and troubleshooting steps you can follow.


Anything too complicated or beyond your scope should be handled by a professional.

If you think you want to tackle the repair - and have gotten stuck on a step - reply to your question and I will be glad to help you out.




Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question

Hello ringertfr,
Please use the following link to show how to get at the thermal fuse ( item #7 ..assuming that is what you are asking). The exploded view shows the mounting location and part number too.
Make sure you unplug the dryer before perfoming any service.
Feel free to contact me if I can assist you any further.
Regards,
Rick