Question about Philips 60PP9202 60" Rear Projection HDTV-Ready Television

1 Answer

Red Lights on the Power button blink and picture goes dark

60PL9200D/37

When I unplug it for a while and turn it back on, the picture starts to come on, but it turns dark. And the red lights on the left and right side of the power button blink. Sound but no picture.

Posted by on

  • mefranklin23 Feb 09, 2009

    I have the same problem.

  • peyton013 Feb 23, 2009

    I have the same issue. TV is not that old.

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

60PL9200D/37 When I unplug it for a while and turn it back on, the picture starts to come on, but it turns dark. And the red lights on the left and right side of the power button blink. Sound but no picture.

Posted on Feb 02, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My phillips 60 inch tv 60pl9200d/37 wont turn on the power button flashes blue


Look in the manual. (Page 4)

Turn the TV on From main supply: Ensure that the main supply is turned on. A blue indicator light on the front of the TV lights up. When the TV is turned on by the main supply, the blue indicator light will blink for 45 seconds. This is the lamp's start-up period. When the light goes off, press the POWER button on the remote control or power switch. Press POWER to turn on the TV.

http://www.retrevo.com/support/Philips-60PL9200D-TVs-manual/id/633ag423/t/2/

Telephone number Philips Customer Care Center: 1-888-PHILIPS (744-5477)

Aug 14, 2011 | Philips 60PL9200D Projection Televisions

1 Answer

I have a philips tv model number is 60PL9200D/37. when i turn on my tv the blue power light flashes and the lights and fans cut on but not the actual screen. after a few seconds of blinking the lights and...


U hear alots of clinking too,when tv power on and the projection lamp tried to come on?Yes,tv have a problems with it board call the Ballast board also.This Ballast board only job is to help ignite the tv projection lamp.

Feb 03, 2011 | Philips 60PL9200D Projection Televisions

2 Answers

Philips 60pl9200D/37. Two Red lights on power button.


If the power button is displaying the bulb fault indicator AND overheat indicator lights at the same time, it indicates a faulty cooling fan. The television is smart enough to detect when either of the two cooling fans in the chassis have failed, or aren't spinning fast enough. To prevent overheating and damage, the set will not turn on if a fan is faulty. You'll need a replacement fan.

Jun 20, 2010 | Philips 60PL9200D Projection Televisions

1 Answer

Picture come on for about 2-3 minute, then goes out has sound no picture, red light come on near power button


Ur LCD inverter backlight board is dead.Replaced this LCD inverter backlight board to get the picture back.Tries Shopjimmy.com,Ebay.com to buy a refurbish LCD inverter backlight board for the replacement.

Mar 03, 2010 | Philips 60PL9200D Projection Televisions

1 Answer

I have a wd65100 when powered on i get steady orange light then status blinks red & green,unpluged for 1 hour tv is working but dark picture


Hi

This issue can be due to ballast fan, lamp or high temperature. However, to figure out this we'll need to check for the TV from inside(wiring & testing the components) or the other way is when the lights blink again then follow the procedure given. After you turn on the set, and get the red blinking lights, hold down the Device and Menu buttons together for about 5 seconds.

The Power light will start to flash in a two digit sequence.

For example, 4 flashes, then 1 flash = 41.

Here are the error codes, and the corresponding problem:

12 = No error detected, check power supply.
32 = Lamp Cover is open.
33 = Air filter cover is open.
34 = Lamp abnormality
36 = Light Engine (DMD or Lamp Fan stopped)
37 = Exhaust or Lamp Ballast Fan stopped
38 = Lamp Temperature High
39 = DMD Temperature High
41 = Short is detected
44 = DVI cable between FMT and Engine disconnected

Please do accept the solution if the issue is resolved or else revert for further assistance.

Thanks
Rylee

Jul 28, 2009 | Projection Televisions

2 Answers

Need Help big screen turns on thens goes off


a tv has two components, firstly a power supply produces high voltage to trigger a line transformer, in turn a transformer produces smaller voltages. firstly check if the ht is constantly been produced from a supply, if this is there than go to a line transformer, and check voltages at the output.

Sep 10, 2008 | Panasonic PT-61HX40 61" Rear Projection...

1 Answer

Cannot see picture....


you probobaly. need a new bulb, my dad had the same problem. he orderd a new bulb off the internet and now it works just fine

Apr 22, 2008 | JVC HD-52Z575 52" HDTV

3 Answers

Need Help big screen turns on thens goes off


The unit is going in to shutdown. Sounds like you have a short in the high voltage section.

Feb 18, 2007 | Panasonic PT-53WX52 53" Rear Projection...

Not finding what you are looking for?
Philips 60PP9202 60" Rear Projection HDTV-Ready Television Logo

Related Topics:

889 people viewed this question

Ask a Question

Usually answered in minutes!

Top Philips Projection Televisions Experts

matt martin
matt martin

Level 3 Expert

1191 Answers

Jaime Hernandez

Level 3 Expert

2267 Answers

The Knight
The Knight

Level 3 Expert

68223 Answers

Are you a Philips Projection Television Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...