Question about Arrow No.ETF50PBN Extra Heavy Duty Professional, , Electric Staple Gun/Brad Nailer

1 Answer

The staple holder weld breaks. Can you get a new part ?

I have had 2 of the arrow ETF50PBN and both of them have broken staple holders, I believe they are cold welded. Can a person buy a hole
inside staple holder?
Thank you
Dona Forsberg

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    New Friend:

    An expert that has 1 follower.

  • Expert
  • 40 Answers

If you go to this link on the Arrow website, you can order parts. They do not have the parts diagram available for this tool, so hopefully you still have yours (if you could scan it onto your computer, that would be a good way to store it) http://www.arrowfastener.com/FMPro?-db=web.fp5&-format=product.html&-lay=Entry&-Op=Equals&item=ETF50PBN&-find=

Posted on Mar 13, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I adjust arrow manual staple gun to fit the sizes it recommends...one size seems to be too large


there is usually no adjustment for manual staple guns. you can only fit the length of staples that slide into the holder.

Mar 02, 2015 | Arrow Tools & Hardware - Others

1 Answer

Replacing staples


On the back there is a small metal piece that is spring loaded push it in and down and that should release it pull it out and slide staples in replace assembly remembering to push in and up to reinstall holder .Hope this helps.
Bob

Jul 18, 2014 | Arrow Fastener T72 Wire & Cable Staple Gun

1 Answer

Staple gun quit working. Not getting any power to the trigger switch. Is it possible to get a replacement circuit board?


It appears that Arrow does not offer a replacement switch/circuit board even though it is usually the first thing to fail which makes your staple gun worthless.The only solution I know of is to throw your staple gun away and buy another one from someone else that offers replacement parts and stands behind their products. Arrow does offer a limited guarantee from date of purchase

Sep 12, 2010 | Arrow Electric Staple And Nail Gun...

1 Answer

I cannot figure out how to load an Arrow T50P staple gun


Turn it upside down. On the end opposite where the staple comes out look for a tab on each side you squeeze to release the staple holder, the staples go in to this holder upside down as well, just push it back in until the releases catch and hold it in. Hope this helps.

Jun 17, 2010 | Arrow T50P ARROW STAPLE GUN

2 Answers

Instruction book for Arrow ETF50P staple gun . lost the instructions and can't figure out how to insert the staples in the gun


Look at the rear of the stapler. Push in then down on the stapler tensioner to release it from the rear of the gun. Slide the tensioner out. Next slide the new staples over the rail and into the gun with points down. Slide the spring tensioner back in and connect it to the stapler by maneuvering its clip down and then up.

Apr 19, 2010 | Arrow No.ETF50PBN Extra Heavy Duty...

1 Answer

How do I load staples? I can not find my manual!


On the back bottom of the stapler there is a rod you need to lift up and then pull out on it should come out

Nov 15, 2009 | Arrow No.ETF50PBN Extra Heavy Duty...

1 Answer

How do i add more staples


Hi, You cannot add staples while there are still some left in the cartridge, you will have to wait until it is all finished, the paper holder comes out from the bottom of the cartridge, remove the old staple paper holder, pay careful attention or put a mark on the outside, now you are ready to insert the new staples in the cartridge. First you need to remove the new staples and take out the wrapper carefully, line up the arrow with the cartridge and insert it into the cartridge then snap it into place, replace the cartridge in the machine when you are done.
Thats it.
This fix is for the small finisher that hangs on the machine, it`s called M1 Finisher.

If you need a service manual for this model machine you can get it here
http://www.techmanualarchives.com/canon-irc-2620_3200-_3220-service-amp-parts--manual-25171.html

Oct 07, 2009 | Canon Image Runner 3320I Copier

1 Answer

I cant get the rod out to put new staples in


These things are weird. What you gotta do is push on the end and lift it up and then pull. Jiggle it around like you would trying to get a key to work. Good luck!

Sep 19, 2009 | Arrow No.ETF50PBN Extra Heavy Duty...

1 Answer

The door at the back of the staple gun won't close


You may have too many staples loaded in the magazine.

Jun 05, 2009 | Arrow No.ETF50PBN Extra Heavy Duty...

Not finding what you are looking for?
Arrow No.ETF50PBN Extra Heavy Duty Professional, , Electric Staple Gun/Brad Nailer Logo

239 people viewed this question

Ask a Question

Usually answered in minutes!

Top Arrow Tools & Hardware - Others Experts

JOHN LAPIER

Level 3 Expert

2422 Answers

Paul Sikkema
Paul Sikkema

Level 2 Expert

171 Answers

yadayada
yadayada

Level 3 Expert

71694 Answers

Are you an Arrow Tool and Hardware - Other Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...