Question about Sony PlayStation 2 (PS2) Console

1 Answer

Video out settings changed to RBG;Complete loss of signal

Video out settings were changed

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Governor:

    An expert whose answer got voted for 20 times.

  • Expert
  • 132 Answers

RGB is componet, you need to turn on the PS2 with the disk tray open or no game in it and go to system settings and change it to
Y/Pc/Br

which is composite.

Posted on Feb 01, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Connect rbg cable tv


Contact Arris Support ARRIS for Consumers

Mark
Motorola Support

Apr 23, 2014 | Motorola Audio Players & Recorders

1 Answer

Looks like its scrambled!!


Sounds like the TV can't handle the resolution that is being supplied or it is set for wrong resolution.

Jan 22, 2008 | Toshiba 53HX71 53" Rear Projection...

1 Answer

DVR Video Loss


Charter was out and changed modems, after that I noticed we lost signal.

Aug 16, 2012 | QPS Q-See QSDR008RTC-500 8 Channel H.264...

1 Answer

Not a single is coming on our airtel digitel tv from 4 days my ID no ;3001839314


If you are experiencing a complete signal loss on your VIP722 receiver, you can try some troubleshooting steps, ( http://www.dishnetwork.com/SupportSection/complete-sig-loss ) and it may resolve your issue or you will need to contact Dish Network for advance troubleshooting and a possible Service Technician Visit!

Oct 01, 2010 | DISH Network ViP722 DTV Receiver /...

1 Answer

I have an AMU monitor and i have a problem, when i turn it on it says that there is no RBG signal! and then goes into standby mode. i have tryed several other monitors on my computer tower and i get the...


There is no signal coming out. Try inspecting the video card. You can always reset the BIOS of the motherboard by removing the small battery and replacing it.

Aug 26, 2010 | Computers & Internet

1 Answer

Why does my projection look green if the colors are right on the computer?


I'm going to guess that you are using an RGB cable to connect to the projector and the projector is expecting a composite signal. The composite signal would be what uses a yellow connector when you use hte red/whjite/yellow type of cable. All of the video is carried by the yellow. If the projector is expecting this and you send out component (RBG in this case), then the only video signal processed is the green. Since the green also contains the sync signal, the picture will be seen but green.

Check the menus on the projector. You should find a video selection area that will allow you to change to component input.

Please update this if you have any more questions.

Dan

Feb 03, 2010 | Dell 2400MP DLP Projector

2 Answers

I am trying to project a presentation from my toshiba laptop to a Hitachi data projector (new). The desktop and all have a red/pink tinge. i even tried just going into my pictures and doing a slide show -...


This sounds like a bad cable... do you tight the scew? inspect the cable connector at each ends to dbl check that there is no damaged pin, and also on the projector side...

Oct 15, 2009 | Computers & Internet

1 Answer

RBG error appears on screen (no signal)


The monitor is not getting any signal from the computer. Try a different monitor and / or cable. Could also be bad video card.

Oct 06, 2009 | E-Machines eMachines Desktop PC

1 Answer

NO Picure


Hi 1prosource

I concur:) Glad you got it sorted out. Any other dramas you may have, just give me a hoy :)

regards
robotek

Jun 02, 2008 | Sony STR-DG510 Receiver

1 Answer

Component Video


Make sure that your source units (DVD, Cable/Satellite, etc) are ALSO plugged into the reciever using Component (you cant have multiple types like S-Video, Composite and Component mixed and matched). Also make sure your TV is on the appropriate input.

Sep 14, 2007 | Sony STR-DE597 Receiver

Not finding what you are looking for?
Sony PlayStation 2 (PS2) Console Logo

Related Topics:

112 people viewed this question

Ask a Question

Usually answered in minutes!

Top Sony Video Game Consoles & Games Experts

Iron
Iron

Level 3 Expert

3018 Answers

shaun taylor

Level 3 Expert

1450 Answers

marley mcelhinney

Level 3 Expert

490 Answers

Are you a Sony Video Game Console and Game Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...