Question about Mitsubishi WD-62525 62" Rear Projection HDTV

1 Answer

Mitsubishi WD-62528 error code 45

Tv will turn on but only stays on for about 5 min then wont turn back on for a few hours then only 5 min tried reset no luck pressed device + menu got four blinks then five so error code 45 but cant find out what that means

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 25 Answers

Go to the manufacture site they should tell you what the code means if not try techlore.com

Posted on Feb 08, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Mitsubishi WD-65638 turns itself off and I see no status codes afterwards


Press menu and input on front of TV for 5 seconds. Green light will flash two digit code 5 times. '12' is no error(no problem.)

May 22, 2014 | Mitsubishi WD-65638 65" DLP HDTV

1 Answer

How do i reset the lamp timer on my mitsubishi model wd-60735


Not going to fix that if the set even has that (which I doubt). Was the lamp a Mitsubishi or a generic cheap replacement?

when set goes off look to see if lamp is off or on, If you have to turn set back on or when its off, do the sets self check--press and hold both the menu and device buttons at same time for 5 second and release both---power light should blink a digit error code like 1,2, blinks pause and repeat that (1,2 is no error found and 3,7 is lamp issue.

Dec 23, 2012 | Mitsubishi WD-60735 Projection Television

2 Answers

Mitsubishi wd-65734 65 in. Tv shuts off on its own and red lamp light comes on. after a few minutes i can turn it back on and works fine for a few min to an hr before doing it again. anyone no wat the...


Same thing on my tv after replacing lamp. Lamp manufacturer advised me that after changing bulb, tv must be reset or tv will go into safety mode and will not turn on. To do this on my model WD-65734 you must hold reset button in with a pen or paperclip for about 10 secs.The LED will start blinking for a few mins. When itstops you need to unplug tv set for about 1 hour. After this the tv will be reset.

Apr 22, 2012 | Mitsubishi WD-65734 65" HDTV

1 Answer

How to replace lamp


1. Turn the tv off and unplug it. 2. carefully access the back of the tv. 3. when facing the back of the tv on the lower left hand side there is a cover held on by two phillips screws remove this cover. 4. After cover is removed you can see the lamp which is also held in by two phillips screws, these screws only loosen and do not completely remove from the lamp. 5. after loosening the screws there is a handle in the center of the lamp, take the lamp by the handle and remove it from the tv. 6. reverse this process to install lamp.

I hope this helps you. After you replace your lamp make sure you reset the hours for your lamp. Press tv menu, select the setup menu, and then select the lamp reminder option to reset hours to zero.

Nov 17, 2010 | Mitsubishi WD-62528 62 in. LCD Television

1 Answer

The lamp went out and i change it but the lamp light is srill on and the tv come ongos to a blue screen about 3-5 min. then gos off


blue screen usually is signal related. it will shut down after a few minutes if it doesnt detect a signal.

Mar 16, 2010 | Mitsubishi WD-62528 62" LCD HDTV

3 Answers

Just replaced the bulb in my wd-62528 dlp tv, thought that would fix the problem of it not turning on, didnt. If i unplug the tv and plug it in the green light blinks for 30 sec. and thats it. The tv still...


Hi, I'm not a service expert. I too own a WD-62528 DLP TV with exactly the same problem. Manufacture date Nov. 2005.

I have found in another forum (CNET) that this is a very well known problem. And that Mitsubishi (MDEA) is not taking responsibility for it. A group of people tried to make a Class Lawsuit but it was rejected. Also other people found that this TV actually does not display 1080i resolution, that is a separate problem from the lamp issue.

If you are able to solve this problem with the TV (blinking lights requesting a new lamp all the time and TV turning off by itself), please let me know. If you want a link to the other forum, let me know and I will send the link.

Also, please don't be discouraged from trying to find a solution. Keep trying.

Jorge Aguilar
Houston

Oct 29, 2009 | Mitsubishi WD-62528 62" LCD HDTV

1 Answer

Mitsubishi 65" DLP HDTV, Status light is red, no picture


Check your lamp; it may have blown. Sound, no picture and a red light are classis signs a lamp has failed.

Feb 02, 2009 | Mitsubishi WD-62528 62 in. LCD Television

2 Answers

Green Blinking Timer Light Mitsubishi WD-62527


hold the menu bottun for 10 seconds
after press power

see if that works

Sep 22, 2007 | Mitsubishi WD62527 62 in. LCD HDTV

Not finding what you are looking for?
Mitsubishi WD-62525 62" Rear Projection HDTV Logo

147 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Televison & Video Experts

matt martin
matt martin

Level 3 Expert

1207 Answers

The Knight
The Knight

Level 3 Expert

72670 Answers

Jaime Hernandez

Level 3 Expert

2296 Answers

Are you a Mitsubishi Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...